Woods Equipment TS1680Q manual Joint Assembly, Install Cups

Page 37

2.With snap rings removed, support drive in vise, hold yoke in hand and tap on yoke to drive cup up out of yoke. See Figure 24.

Figure 25. Remove Cups

3.Clamp cup in vise as shown in Figure 25 and tap on yoke to completely remove cup from yoke. Repeat Step 2 and Step 3 for opposite cup.

Figure 26. Remove Cups

4.Place universal cross in vise as shown in Figure 26 and tap on yoke to remove cup. Repeat Step 3 for

final removal. Drive remaining cup out with a drift and hammer.

U-Joint Assembly

1.Place seals securely on bearing cups. Insert cup into yoke from outside and press in with hand pressure as far as possible. Insert journal cross into bearing cup with grease fitting away from shaft. Be careful not to disturb needle bearings. Insert another bearing cup directly across from first cup and press in as far as possible with hand pressure.

2.Trap cups in vise and apply pressure. Be sure journal cross is started into bearings and continue pressure with vise, squeezing in as far as possible. Tapping the yoke will help.

3.Seat cups by placing a drift or socket (slightly smaller than the cup) on cup and rap with a hammer. See Figure 27. Install snap ring and repeat on opposite cup

4.Repeat Step 1 and Step 2 to install remaining cups in remaining yoke.

5.Move both yokes in all directions to check for free movement. If movement is restricted, rap on yokes sharply with a hammer to relieve any tension. Repeat until both yokes move in all directions without restriction.

Figure 27. Install Cups

MAN0577 (6/29/2007)

Dealer Service 37

 

 

Page 36 Page 38
Image 37
Page 36 Page 38
Contents Rotary Cutter Introduction LEA EL Instructivo Table of ContentsGeneral Information SpecificationsFree Mower Safety Video Training Package for Rotary Mowers/Cutters-English/Spanish Training Package for Rotary Mowers/Cutters-EnglishTraining Safety RulesPreparation Transportation OperationMaintenance Storage Be Careful Safety & Instructional Decals1000 RPM 33347E Tractor Stability OperationConnect Cutter to Tractor PULL-TYPE Connect Cutter to Tractor Mounted Category 2 & 3 Quick Hitches Driveline Adjustment MountedShorten Driveline Driveline Interference Check Cutting Height AdjustmentMounted Units Pull-Type UnitsDriveline Adjustment PULL-TYPE Attitude Adjustment PULL-TYPEWheel Spacing Blade SelectionMowing Tips Cutter OperationTransporting Owners Responsibility PRE-OPERATION Check ListBlocking Method Owner ServiceLubrication Gearbox Lubrication= Jackstand Placement Blade Servicing Installing BladesRemoving Blades Figure Sharpening BladesRepairing Optional Chain Shielding Slip Clutch AdjustmentShielding Repair Servicing Tires Safely Flexible Coupler Rubber Disk ReplacementAfter Each Use CleaningProblem Possible Cause Solution TroubleshootingTroubleshooting Gearbox Maintenance Dealer ServiceSeal Replacement Seal InstallationSide Gearbox Repair Figure Remove Gearbox from Cutter Horizontal Shaft Seal Repair FigureDisassemble Gearbox Assemble GearboxSide Gearbox Assembly Reinstall GearboxHhcs Center Gearbox Repair FigureAssemble Gearbox Figure Disassemble Gearbox FigureCrossbar Side Drive ServiceCrossbar Removal Crossbar Removal Crossbar InstallationCrossbar Timing Joint DisassemblyUniversal Joint Repair Install Cups Joint AssemblyDealer SET-UP Instructions Assembly InstructionsTS1680 PULL-TYPE Cutter Rear Half TS1680 Pull-Type Cutter Assembly Rear Half Install SMV EmblemInstall CV Driveline Figure Front Half Figure Install TongueTS1680 Pull-Type Cutter Assembly Front Half Install Tailwheel Arms Install A-FrameInstall Hydraulic Hoses TS1680 Mounted Cutter FigureGR5 Install Chain Shielding Optional Install SMV Emblem Semi-MountedALL Models Fill Gearboxes Side GearboxesInstall Stump Jumper Optional Install Light KIT OptionalShredder Kit Installation Install Shredder KIT OptionalStationary Blade Positions for 1000 RPM and 540 RPM Models PRE-DELIVERY Check List Dealer Check ListsDelivery Check List Parts Index Main Frame Assembly REF Part PULL-TYPE Assembly Front Half See page 62 -or See PULL-TYPE Assembly Rear HalfREF Part QTY Description Wheel & Tire AssemblyMounted Cutter Assembly Tailwheel see Center Gearbox Assembly Assembly TS1680 -or Side Gearbox Assembly 1024795 Complete 540 RPM Gearbox Type a 40 RPM Front CV Drive Assembly Type B 540 RPM Front CV Drive Assembly RPM 1-3/8 21-Splined Type a 1000 RPM Front CV Drive AssemblyRPM 1-3/4 20-Splined Type B 1000 RPM Front CV Drive Assembly Rear FIXED-LENGTH Drive for Constant Velocity Drive Slip Clutch Drive Assembly Mounted Flexible Coupler Spring Wheel ARM Assembly Pull Type Caster ARM Assembly Mounted Caster ARM Assembly Chain Shielding Standard Light KIT Optional Stump Jumper Assembly OptionalShredder KIT Optional 2 x 8 Stroke Hydraulic Cylinder Optional Crossbar Puller Optional Hydraulic Cylinder Stroke Control KIT OptionalSAE Series Torque Chart Bolt Torque ChartMetric Series Abbreviations Bolt Size ChartIndex AssemblyWarranty Woods Equipment Company MAN0577

TS1680, TS1680Q specifications

Woods Equipment has long been a prominent name in the agricultural and landscaping sectors, and its TS1680Q and TS1680 models further cement this reputation. Designed for versatility and reliability, both models shine in various applications, ranging from mowing to maintaining landscapes.

One of the standout features of the Woods TS1680Q and TS1680 is their robust build quality. Crafted with heavy-duty materials, these models are engineered to withstand the rigors of tough terrain and demanding workloads. The TS1680Q, being the quieter variant, employs advanced sound-dampening technologies, ensuring that operators can work without the disruptive noise typical of many competitors.

With a cutting width of 68 inches, both models are designed for efficiency. The wide cutting deck not only allows operators to cover more ground quickly but also ensures a clean and even cut on various grass types. The TS1680Q further enhances mowing precision with its unique floating deck design. This feature enables the cutting deck to follow ground contours, reducing scalping on uneven surfaces.

Another notable characteristic is the versatility of attachment options. Both models come equipped with a category 1 three-point hitch which allows for easy attachment of numerous implements. This adaptability means operators can use the TS1680Q and TS1680 for other tasks, such as tilling or hauling, making it a multi-functional powerhouse for any farm or landscape project.

The hydraulic system on these models is engineered for high performance. With user-friendly controls and responsive feedback, operators can adjust settings with ease. Combined with a powerful engine, the TS1680Q and TS1680 offer reliable performance and energy efficiency, contributing to reduced fuel expenditure in the long run.

Safety features are also a priority, with shields and guards designed to protect operators during use. The controls are ergonomically situated to minimize potential hazards. Additionally, the low center of gravity design ensures stable operation, reducing the risk of tipping especially while working on inclines.

In conclusion, the Woods Equipment TS1680Q and TS1680 models are designed with the modern user in mind. Their blend of durability, innovative technology, and operational versatility makes them a top choice for both agricultural use and landscaping projects. Whether you're a farmer looking for reliable mowing solutions or a landscaper in need of a versatile implement, these models deliver exceptional performance and value.
Top Page Image Contents