Woods Equipment TS1680Q manual Install Light KIT Optional, Install Stump Jumper Optional

Page 45

1. Left light assembly (not shown)

2. Right light assembly (not shown)

3. Light bracket

4. Electronic module

5. 7" Tie strap

6. #10 x 1/2 Self-tapping screw

7. 1/4 NC x 1 HHCS GR5

8. 1/4 Lock nut

9. 3/8 NC x 4 HHCS GR5

10. 3/8 Flat washer

11. 3/8 NC Flange lock nut

12. Wire harness

Figure 32. Light Kit Installation

INSTALL LIGHT KIT (OPTIONAL)

1.Drill two 1/2" holes through both outer deck channels using dimensions shown in Figure 32.

2.Drill two 11/64" holes into deck plate as shown.

3.Install electronic module (4) to deck using self tapping screws (6).

4.Route wires as shown. Be sure wire labeled "Left" is routed to the left light.

5.Install light brackets (3) on outer deck rails as shown. Secure with cap screws (9), washers (10) and lock nuts (11).

6.Secure left and right lamp (1 & 2) to brackets (3) using cap screws (7) and lock nuts (8) as shown.

7.Connect lights to wire harness (4).

8.Route main wire along hydraulic hose and secure to hose using wire ties (5).

INSTALL STUMP JUMPER (OPTIONAL)

1.Remove blade pins and blades from crossbar.

2.Remove straps (2) from stump jumper (1).

3.Insert blade pin through blade, stump jumper (1) and crossbar. Reinstall spacer on blade pin and install new jam nut.

4.Attach straps (2) to stump jumper (1) and crossbar using carriage bolts (3), washers (4), lock washers

(5) and hex nuts (6).

3.5/8 NC x 1-1/2 Carriage bolt

4.5/8 Standard flat washer

5.5/8 Heavy lock washer

6.5/8 NC Hex nut

Figure 33. Stump Jumper Assembly

(Rev. 8/31/2007) MAN0577 (6/26/2007)

Assembly 45

Image 45
Contents Rotary Cutter Introduction LEA EL Instructivo Table of ContentsGeneral Information SpecificationsFree Mower Safety Video Training Package for Rotary Mowers/Cutters-English/Spanish Training Package for Rotary Mowers/Cutters-EnglishSafety Rules TrainingPreparation Transportation OperationMaintenance Storage Be Careful Safety & Instructional Decals1000 RPM 33347E Operation Tractor StabilityConnect Cutter to Tractor PULL-TYPE Connect Cutter to Tractor Mounted Driveline Adjustment Mounted Category 2 & 3 Quick HitchesShorten Driveline Driveline Interference Check Cutting Height AdjustmentMounted Units Pull-Type UnitsDriveline Adjustment PULL-TYPE Attitude Adjustment PULL-TYPEWheel Spacing Blade SelectionCutter Operation Mowing TipsTransporting Owners Responsibility PRE-OPERATION Check ListBlocking Method Owner ServiceLubrication Gearbox Lubrication= Jackstand Placement Blade Servicing Installing BladesRemoving Blades Figure Sharpening BladesSlip Clutch Adjustment Repairing Optional Chain ShieldingShielding Repair Servicing Tires Safely Flexible Coupler Rubber Disk ReplacementAfter Each Use CleaningProblem Possible Cause Solution TroubleshootingTroubleshooting Gearbox Maintenance Dealer ServiceSeal Replacement Seal InstallationSide Gearbox Repair Figure Remove Gearbox from Cutter Horizontal Shaft Seal Repair FigureDisassemble Gearbox Assemble GearboxSide Gearbox Assembly Reinstall GearboxHhcs Center Gearbox Repair FigureAssemble Gearbox Figure Disassemble Gearbox FigureSide Drive Service CrossbarCrossbar Removal Crossbar Removal Crossbar InstallationJoint Disassembly Crossbar TimingUniversal Joint Repair Install Cups Joint AssemblyAssembly Instructions Dealer SET-UP InstructionsTS1680 PULL-TYPE Cutter Rear Half TS1680 Pull-Type Cutter Assembly Rear Half Install SMV EmblemInstall CV Driveline Figure Front Half Figure Install TongueTS1680 Pull-Type Cutter Assembly Front Half Install Tailwheel Arms Install A-FrameInstall Hydraulic Hoses TS1680 Mounted Cutter FigureGR5 Install Chain Shielding Optional Install SMV Emblem Semi-MountedALL Models Fill Gearboxes Side GearboxesInstall Stump Jumper Optional Install Light KIT OptionalShredder Kit Installation Install Shredder KIT OptionalStationary Blade Positions for 1000 RPM and 540 RPM Models Dealer Check Lists PRE-DELIVERY Check ListDelivery Check List Parts Index Main Frame Assembly REF Part PULL-TYPE Assembly Front Half See page 62 -or See PULL-TYPE Assembly Rear HalfREF Part QTY Description Wheel & Tire AssemblyMounted Cutter Assembly Tailwheel see Center Gearbox Assembly Assembly TS1680 -or Side Gearbox Assembly 1024795 Complete 540 RPM Gearbox Type a 40 RPM Front CV Drive Assembly Type B 540 RPM Front CV Drive Assembly Type a 1000 RPM Front CV Drive Assembly RPM 1-3/8 21-SplinedRPM 1-3/4 20-Splined Type B 1000 RPM Front CV Drive Assembly Rear FIXED-LENGTH Drive for Constant Velocity Drive Slip Clutch Drive Assembly Mounted Flexible Coupler Spring Wheel ARM Assembly Pull Type Caster ARM Assembly Mounted Caster ARM Assembly Chain Shielding Standard Light KIT Optional Stump Jumper Assembly OptionalShredder KIT Optional 2 x 8 Stroke Hydraulic Cylinder Optional Crossbar Puller Optional Hydraulic Cylinder Stroke Control KIT OptionalBolt Torque Chart SAE Series Torque ChartMetric Series Abbreviations Bolt Size ChartIndex AssemblyWarranty Woods Equipment Company MAN0577

TS1680, TS1680Q specifications

Woods Equipment has long been a prominent name in the agricultural and landscaping sectors, and its TS1680Q and TS1680 models further cement this reputation. Designed for versatility and reliability, both models shine in various applications, ranging from mowing to maintaining landscapes.

One of the standout features of the Woods TS1680Q and TS1680 is their robust build quality. Crafted with heavy-duty materials, these models are engineered to withstand the rigors of tough terrain and demanding workloads. The TS1680Q, being the quieter variant, employs advanced sound-dampening technologies, ensuring that operators can work without the disruptive noise typical of many competitors.

With a cutting width of 68 inches, both models are designed for efficiency. The wide cutting deck not only allows operators to cover more ground quickly but also ensures a clean and even cut on various grass types. The TS1680Q further enhances mowing precision with its unique floating deck design. This feature enables the cutting deck to follow ground contours, reducing scalping on uneven surfaces.

Another notable characteristic is the versatility of attachment options. Both models come equipped with a category 1 three-point hitch which allows for easy attachment of numerous implements. This adaptability means operators can use the TS1680Q and TS1680 for other tasks, such as tilling or hauling, making it a multi-functional powerhouse for any farm or landscape project.

The hydraulic system on these models is engineered for high performance. With user-friendly controls and responsive feedback, operators can adjust settings with ease. Combined with a powerful engine, the TS1680Q and TS1680 offer reliable performance and energy efficiency, contributing to reduced fuel expenditure in the long run.

Safety features are also a priority, with shields and guards designed to protect operators during use. The controls are ergonomically situated to minimize potential hazards. Additionally, the low center of gravity design ensures stable operation, reducing the risk of tipping especially while working on inclines.

In conclusion, the Woods Equipment TS1680Q and TS1680 models are designed with the modern user in mind. Their blend of durability, innovative technology, and operational versatility makes them a top choice for both agricultural use and landscaping projects. Whether you're a farmer looking for reliable mowing solutions or a landscaper in need of a versatile implement, these models deliver exceptional performance and value.