Woods Equipment TS1680Q manual Install Shredder KIT Optional, Shredder Kit Installation

Page 46

INSTALL SHREDDER KIT (OPTIONAL)

1.Remove nut (9) and spacer (10) from blade pin (11). While keeping the lower formed blade installed, install double-edge blade (2) with offset upwards towards deck.

2.Reinstall spacer (10). Install new nut (9) and torque to 664 lbs-ft. Make sure blades are free to pivot.

3.Install blade holder (1) to link between rear V-baffle of machine using four cap screws (7) and four lock nuts (8).

NOTE: Blade holder installs on right side of cutter for 1000 rpm cutters (shown) and on the left side for 540 rpm cutters. See Figure 35.

4.Attach two stationary blades (3) to blade holder using cap screws (7) and lock nuts (8).

5.Attach plate (4) and two stationary blades (3) to link between front V-baffle of machine using cap screws (6) and lock nuts (8).

NOTE: Blades located on right side of cutter for 1000 rpm cutters (shown) and on the left side for 540 rpm cutters.

6.Attach three stationary blades (3) to front frame of cutter using carriage bolts (5) and lock nuts (8).

NOTE: Center blade is located left of cutter center for 1000 rpm cutters (shown) and right of center for 540 rpm cutters.

1.	Blade holder	6.	5/8 NC x 3 HHCS GR5
2.	Double edge blade, .5 x 4 x 22.5	7.	5/8 NC x 1-3/4 HHCS GR5
3.	Double edge blade, .38 x 1 x 11.13	8.	5/8 NC Lock nut
4.	Plate	9.	1-1/4 Locking jam nut
5.	5/8 NC x 1-1/2 Carriage bolt	10.	Flange bushing
		11.	Blade pin

Figure 34. Shredder Kit Installation

46 Assembly	MAN0577 (6/29/2007)

Image 46

Contents

Rotary Cutter Introduction Table of Contents LEA EL InstructivoSpecifications General InformationFree Mower Safety Video Training Package for Rotary Mowers/Cutters-English Training Package for Rotary Mowers/Cutters-English/SpanishTraining Safety RulesPreparation Operation TransportationMaintenance Storage Safety & Instructional Decals Be Careful1000 RPM 33347E Tractor Stability OperationConnect Cutter to Tractor PULL-TYPE Connect Cutter to Tractor Mounted Category 2 & 3 Quick Hitches Driveline Adjustment MountedShorten Driveline Mounted Units Cutting Height AdjustmentDriveline Interference Check Pull-Type UnitsWheel Spacing Attitude Adjustment PULL-TYPEDriveline Adjustment PULL-TYPE Blade SelectionMowing Tips Cutter OperationTransporting PRE-OPERATION Check List Owners ResponsibilityLubrication Owner ServiceBlocking Method Gearbox Lubrication= Jackstand Placement Removing Blades Figure Installing BladesBlade Servicing Sharpening BladesRepairing Optional Chain Shielding Slip Clutch AdjustmentShielding Repair Flexible Coupler Rubber Disk Replacement Servicing Tires SafelyCleaning After Each UseTroubleshooting Problem Possible Cause SolutionTroubleshooting Seal Replacement Dealer ServiceGearbox Maintenance Seal InstallationDisassemble Gearbox Horizontal Shaft Seal Repair FigureSide Gearbox Repair Figure Remove Gearbox from Cutter Assemble GearboxReinstall Gearbox Side Gearbox AssemblyCenter Gearbox Repair Figure HhcsDisassemble Gearbox Figure Assemble Gearbox FigureCrossbar Side Drive ServiceCrossbar Removal Crossbar Installation Crossbar RemovalCrossbar Timing Joint DisassemblyUniversal Joint Repair Joint Assembly Install CupsDealer SET-UP Instructions Assembly InstructionsTS1680 PULL-TYPE Cutter Rear Half Install SMV Emblem TS1680 Pull-Type Cutter Assembly Rear HalfFront Half Figure Install Tongue Install CV Driveline FigureTS1680 Pull-Type Cutter Assembly Front Half Install Hydraulic Hoses Install A-Frame Install Tailwheel Arms TS1680 Mounted Cutter FigureGR5 ALL Models Fill Gearboxes Install SMV Emblem Semi-MountedInstall Chain Shielding Optional Side GearboxesInstall Light KIT Optional Install Stump Jumper OptionalInstall Shredder KIT Optional Shredder Kit InstallationStationary Blade Positions for 1000 RPM and 540 RPM Models PRE-DELIVERY Check List Dealer Check ListsDelivery Check List Parts Index Main Frame Assembly REF Part PULL-TYPE Assembly Front Half See page 62 -or PULL-TYPE Assembly Rear Half SeeWheel & Tire Assembly REF Part QTY DescriptionMounted Cutter Assembly Tailwheel see Center Gearbox Assembly Assembly TS1680 -or Side Gearbox Assembly 1024795 Complete 540 RPM Gearbox Type a 40 RPM Front CV Drive Assembly Type B 540 RPM Front CV Drive Assembly RPM 1-3/8 21-Splined Type a 1000 RPM Front CV Drive AssemblyRPM 1-3/4 20-Splined Type B 1000 RPM Front CV Drive Assembly Rear FIXED-LENGTH Drive for Constant Velocity Drive Slip Clutch Drive Assembly Mounted Flexible Coupler Spring Wheel ARM Assembly Pull Type Caster ARM Assembly Mounted Caster ARM Assembly Chain Shielding Standard Stump Jumper Assembly Optional Light KIT OptionalShredder KIT Optional 2 x 8 Stroke Hydraulic Cylinder Optional Hydraulic Cylinder Stroke Control KIT Optional Crossbar Puller OptionalSAE Series Torque Chart Bolt Torque ChartMetric Series Bolt Size Chart AbbreviationsAssembly IndexWarranty Woods Equipment Company MAN0577