Seasonal Lubrication, Blades | Woods Equipment BW2400XQ, BW1620X

Seasonal Lubrication

In addition to the daily recommended lubrication, a more extensive application is recommended season- ally.

1.Fill CV double yokes with 20 pumps of grease with the joints in a straight line.

2.Articulate CV body to maximum angle several times to ensure full coverage of joints.

3.Place joints in the straight position and a add 10 additional pumps of grease to both joints.

4.Wipe telescoping drive clean of all old grease and contaminants.

5.Add a thin layer of new grease over telescoping drive.

BLADES

Before working underneath, read manual instructions, securely block up, and check stabil- ity. Secure blocking prevents equipment from dropping due to hydraulic leak down, hydraulic system failure, or mechanical component failure.

Blade Removal (Figure 6)

7.Blade pin

8.Crossbar assembly

9.Shim, 18 ga

10.Shim, 20 ga

11.Keyhole plate

12.Blade lock clip

50.1/2 NC x 1-1/4 HHCS GR5

Figure 6. Blade Assembly

1.Disconnect driveline from tractor PTO.

2.Raise cutter and block securely (see Figure 5).

3.Align crossbar (8) with blade access hole in the cutter frame. Remove cap screw (50), blade pin

lock clip (12), keyhole plate (11), and shims (9 & 10). Carefully drive blade pin (7) out of crossbar.

4.Rotate crossbar and repeat for opposite blade.

NOTICE

If blade pin (7) is seized in crossbar and extreme force will be needed to remove it, support crossbar from below to prevent gearbox damage.

Blade Installation (Figure 6)

CAUTION

Your dealer can supply genuine replacement blades. Substitute blades may not meet original equipment specifications and may be dangerous.

NOTICE

Crossbar rotation has clockwise rotation on left gearbox and counterclockwise rotation on the right gearbox when looking down on cutter. The center gearbox has counterclockwise rotation on all mod- els except BW1620XQREV, which has clockwise. Be sure to install blade cutting edge to lead in the correct rotation.

NOTE: Always replace or sharpen both blades at the same time.

1.Inspect blade pin (7) for nicks or gouges, and if you find any, replace the blade pin.

2.Insert blade pin through the blade. Blade should swivel on blade pin; if it doesn’t, determine the cause and correct.

3.Align crossbar (8) with blade access hole in cutter frame. Apply a liberal coating of Never-Seez®or equivalent to blade pin and crossbar hole. Make sure blade offset is down away from cutter.

4.Insert blade pin (7) through blade. Push blade pin through crossbar.

5.Install shims (9 & 10) over blade pin.

NOTE: Only use enough shims to allow keyhole plate (11) to slide into blade pin groove.

6.Install blade clip (12) over keyhole plate and into blade pin groove.

7.Secure into position with cap screw (50). Torque cap screw to 85 lbs-ft.

8.Repeat steps for opposite side.

NOTE: Blade should be snug but should swivel on pin without having to exert excessive force. Blade should not move more than a 1/4 inch up or down at the tip. Keep any spacers not used in the installation as replacements or for future installation.

MAN0764 (11/5/2008)	Owner Service 21

BW2400X, BW1620XQREV, BW2400XQ, BW1620X, BW1620XQ specifications

Woods Equipment has established itself as a trusted name in the landscape and agricultural equipment sector, offering a wide range of high-performance products tailored to meet various needs. Among its standout offerings are the BW1620XQ, BW1620X, BW2400XQ, BW1620XQREV, and BW2400X models, known for their robust design and exceptional functionality.

The BW1620XQ is designed for efficient brush cutting, making it an ideal choice for land maintenance and clearing dense underbrush. One of its main features is the heavy-duty construction, which ensures durability even under the toughest conditions. This model is equipped with a reinforced deck, providing added strength and longevity. It also features a powerful PTO-driven cutting system, allowing it to tackle tough growth with ease.

The BW1620X model offers similar capabilities to the BW1620XQ but is optimized for lighter tasks and smaller properties. It shines in residential applications, where maneuverability and ease of use are paramount. This model is lightweight and easy to attach, making it a favorite among homeowners who require a reliable tool for maintaining their yards and gardens.

For those requiring larger-scale solutions, the BW2400XQ provides increased cutting width and efficiency. This model excels in farm and large property applications, where speed and power are essential. Featuring advanced blade technology, the BW2400XQ offers superior cutting performance and reduced maintenance needs. Additionally, it boasts adjustable height settings, allowing users to customize their cutting experience based on the terrain and type of vegetation.

The BW1620XQREV is a revolutionary model that incorporates newer technology for even better performance and user experience. This model offers enhanced features such as improved blade design for finer cuts and an innovative quick-attach system that enables fast connectivity and disconnection from tractors.

Finally, the BW2400X model is the standard version of the BW2400XQ, providing similar power and efficiency without some of the specialized features, making it a cost-effective solution for users who need reliable equipment without as many bells and whistles.

In conclusion, Woods Equipment's BW1620XQ, BW1620X, BW2400XQ, BW1620XQREV, and BW2400X models each feature unique characteristics tailored to specific applications, ensuring users can find the right tool for their needs, whether for residential landscaping or large-scale agricultural tasks. Their emphasis on durability, efficiency, and user-friendly design makes them a preferred choice across various sectors.