Woods Equipment BW1620XQ, BW2400XQ manual Blade Sharpening Figure, Slip Clutch Adjustment Figure

Page 22

Blade Sharpening (Figure 7)

NOTICE

When sharpening blades, grind the same amount on each blade to maintain balance. Replace blades in pairs. Unbalanced blades will cause excessive vibration, which can damage gearbox bearings. Vibration may also cause struc- tural cracks to cutter.

1.Sharpen both blades at the same time to maintain balance. Follow original sharpening pattern.

2.Do not sharpen blade to a razor edge—leave at least a 1/16" blunt edge.

3.Do not sharpen back side of blade.

Follow Original Pattern

1/16"

Maintain Corner

CD1257-2

Figure 7. Blade Sharpening

SLIP CLUTCH ADJUSTMENT (Figure 8)

The slip clutch is designed to slip so that the gearbox and driveline are protected if the cutter strikes an obstruction.

A new slip clutch or one that has been in storage over the winter may seize. Before operating the cutter, make sure it will slip by performing the following operation:

1.Turn off tractor engine and remove key.

2.Tighten four nuts (12) to remove pressure from the clutch plates (2). Repeat for all three clutches.

3.Start tractor at low throttle and slowly engage PTO and allow clutches to slip for 5 seconds. Disengage PTO and turn off tractor engine.

4.If clutches slip freely, completely loosen nuts (12).

5.If clutch does not slip freely, disassemble and clean plates (4, 6, 7), flange yoke (1), and clutch hub (3).

6.Reassemble clutch.

7.Tighten Belleville spring (5) with nuts (11) until it is against the thrust plate (4) of the clutch. Back off each of the four nuts (11) until gap between Belleville spring and thrust plate is .180 or 3/16” as shown in Figure 8.

8.If a clutch continues to slip when the spring is compressed to .180 or 3/16” gap, check friction discs (2) for excessive wear. Discs are 1/8" when new. Replace discs after 1/16" wear. Minimum disc thickness is 1/16".

NOTE: When storing cutter for long periods of time, relieve the pressure on the clutch discs by tightening the four nuts (12) on each clutch. Completely loosen nuts (12) to return to service.

1.Flange yoke

2.Friction disc

3.Hub, 1-3/4 splined

4.Thrust plate

5.Belleville spring plate

6.Drive plate

7.Drive plate

8.Backup plate

9.Lock assembly

10.M12 x 1.75P x 85 mm Hex head cap screw

11.M12 x 1.75P Hex lock nut

12.M8 x 1.25P Hex nut

Figure 8. Slip Clutch Assembly

22 Owner Service

MAN0764 (11/5/2008)

 

 

Page 21 Page 23
Image 22
Page 21 Page 23
Contents MAN0764 Introduction To the DealerTable of Contents BW1620X, BW1620XQ SpecificationsGeneral Information BW2400X, BW2400XQFree Mower Safety Video SafetyTraining Package for Rotary Mowers/Cutters-English Training Package for Rotary Mowers/Cutters-English/SpanishTraining Safety RulesInstallation PreparationTransportation OperationMaintenance Storage Be Careful Safety & Instructional DecalsPN 1006348 located on split rim wheels Safety Safety Operation Connecting Cutter to TractorOperation Interference Check Cutting Height AdjustmentHydraulic Connection CV Driveline Turning LimitsCutter Operation Attitude Rod Adjustment FigureTractor Operation Cutting Height Normal Mowing WingsShredding Mowing TipsTransporting Lock-UpWing Lock-Up Figure PRE-OPERATION Check ListCenter Section Lock-Up Figure Owner Service Owner ServiceBlocking Method Driveline Lubrication LubricationGearbox Lubrication Description FrequencyBlades Blade Installation FigureSeasonal Lubrication Blade Removal FigureSlip Clutch Adjustment Figure Blade Sharpening FigureCleaning Repairing Rubber ShieldingRepairing Optional Chain Shielding Shielding RepairTroubleshooting TroubleshootingSeal Replacement Figure Dealer ServiceDealer Service Vertical Shaft Seal Replacement FigureWing & Center Gearbox Repair Gearbox Wing & Center Splitter Gearbox Repair Figure Splitter Gearbox Removal Gearbox Installation FigureSplitter Gearbox Disassembly Figure Center ShaftSplitter Gearbox Inspection Splitter Gearbox Assembly FigureSplitter Gearbox Installation Side ShaftCrossbar Removal Crossbar RemovalJoint Disassembly Crossbar InstallationUniversal Joint Repair Joint Assembly Service Tires SafelyCenter Section Assembly AssemblyAssembly Instructions Install Hydraulic Hoses FigureInstall Attitude Rods Figure Install Height Adjustment CylinderInstall SMV Emblem Figure Install Spring Wheel Arms FigureInstall Tongue Figure Install 3-Joint Drive FigureInstall Optional CV Drive Figure CV Drive InstallationInstall Wing Wing AssemblyInstall Wing Cylinder and Transport Lock Install Wing Wheel Yoke Figure Install Wing Wheel Yoke Adjustment LinkHydraulic Cylinder Fill GearboxesOptional Equipment Tandem Wheel Assembly Installation Center Section Right WingInstall Chain or Belt Shielding Chain Shielding Installation Center SectionLink Winch Kit Installation Optional Roller Assembly InstallationCrossbar Installation Left Wing Shredder Installation OptionalCrossbar Installation Right Wing Crossbar Installation Center SectionBW1620X Counterweight Installation BW1620X Counterweight Installation PRE-DELIVERY Check List Dealer Check ListsDealer Check Lists Delivery Check ListParts Index PartsMain Frame Assembly Front Section Part Main Frame Assembly Rear Section 1027070 Center wheel yoke 57050 Access hole cover 10475 Right Wing Shown Part QTY Description Wing & Center Gearbox Assembly 540 RPM 1000 RPM Wing CenterSplitter Gearbox Assembly 540 RPMCenter Deck Drive Assembly Front 3-JOINT Drive Assembly Equal Angle 40728 Inner shieldRear 3-JOINT Drive Assembly Equal Angle Type a 540 RPM Front CV Drive Type B 540 RPM Front CV Drive Type a 1000 RPM Front CV Drive RPM 1-3/8 21-Splined RPM 1-3/4 20-SplinedType B 1000 RPM Front CV Drive Wing Drive Assembly REF Part QTY DescriptionBolt Wheel & Tire Assembly Rubber Shielding Center Section Standard on BW2400 Models Rubber Shielding Wing Standard on BW2400 Models Chain Shielding Center Section Single ROW Double ROWChain Shielding Wing Tandem Axle Wheel Yoke Optional Parts Hydraulic CylindersHydraulic Cylinder Stroke Control KIT Crossbar Puller OptionalShredder KIT Optional BW1620X / BW1620XQ / BW1620XQREV Counterweight BOX Assembly Winch KIT Optional Winch Kit OperationAppendix Bolt Torque ChartSAE Series Torque Chart Metric SeriesBolt Size Chart AbbreviationsIndex IndexWarranty South Illinois Route Post Office Box Oregon, Illinois

BW2400X, BW1620XQREV, BW2400XQ, BW1620X, BW1620XQ specifications

Woods Equipment has established itself as a trusted name in the landscape and agricultural equipment sector, offering a wide range of high-performance products tailored to meet various needs. Among its standout offerings are the BW1620XQ, BW1620X, BW2400XQ, BW1620XQREV, and BW2400X models, known for their robust design and exceptional functionality.

The BW1620XQ is designed for efficient brush cutting, making it an ideal choice for land maintenance and clearing dense underbrush. One of its main features is the heavy-duty construction, which ensures durability even under the toughest conditions. This model is equipped with a reinforced deck, providing added strength and longevity. It also features a powerful PTO-driven cutting system, allowing it to tackle tough growth with ease.

The BW1620X model offers similar capabilities to the BW1620XQ but is optimized for lighter tasks and smaller properties. It shines in residential applications, where maneuverability and ease of use are paramount. This model is lightweight and easy to attach, making it a favorite among homeowners who require a reliable tool for maintaining their yards and gardens.

For those requiring larger-scale solutions, the BW2400XQ provides increased cutting width and efficiency. This model excels in farm and large property applications, where speed and power are essential. Featuring advanced blade technology, the BW2400XQ offers superior cutting performance and reduced maintenance needs. Additionally, it boasts adjustable height settings, allowing users to customize their cutting experience based on the terrain and type of vegetation.

The BW1620XQREV is a revolutionary model that incorporates newer technology for even better performance and user experience. This model offers enhanced features such as improved blade design for finer cuts and an innovative quick-attach system that enables fast connectivity and disconnection from tractors.

Finally, the BW2400X model is the standard version of the BW2400XQ, providing similar power and efficiency without some of the specialized features, making it a cost-effective solution for users who need reliable equipment without as many bells and whistles.

In conclusion, Woods Equipment's BW1620XQ, BW1620X, BW2400XQ, BW1620XQREV, and BW2400X models each feature unique characteristics tailored to specific applications, ensuring users can find the right tool for their needs, whether for residential landscaping or large-scale agricultural tasks. Their emphasis on durability, efficiency, and user-friendly design makes them a preferred choice across various sectors.
Top Page Image Contents