Woods Equipment BW1620X, BW2400X Install Attitude Rods Figure, Install Height Adjustment Cylinder

Page 34

Install Attitude Rods (Figure 23)

4.Attitude rod

21.1" Spacer

29.1" Hex nut

33.1" Flat washer

Figure 23. Attitude Rods Attached to Wheel Yoke

1.Insert attitude rods (4) through front of center section frame, out the center of the deck and through pivot casting in wheel yoke arm assembly. The rod is a very tight fit; use care to prevent thread damage during installation.

2.Slide spacers (21) over rods and install washers (33) and two nuts (34) per rod.

3.Tighten nuts until there is approximately 1 inch of thread exposed past the nuts. Further adjustment will be needed once cutter is attached to tractor drawbar. See Cutting Height Adjustment, page 15.

Install Height Adjustment Cylinder

(Figure 24)

1.Attach base end of cylinder (3) to the cylinder lugs on the rear of the deck using clevis pin (18) and two cotter pins (63).

2.Extend cylinder rod and place transport lock bracket (5) over cylinder rod clevis.

3.Position cylinder rod and transport lock bracket between lugs on wheel yoke tube and align holes.

4.Secure cylinder rod and transport lock bracket to the wheel yoke tube using clevis pin (19) and two cotter pins (63).

5.Install cylinder spacers (6) over cylinder rod as needed. Spacers are used to set cutting height.

6.Install bushing (24), elbow, (23) and hose (22) to the base end of cylinder (3).

NOTE: Make sure a breather fitting is installed in the rod end port of the wheel yoke cylinder.

Optional Ratchet Jack: An optional ratchet (7) is available, and replaces the hydraulic cylinder. Install ratchet jack using the same procedure and hardware used for the installation of the hydraulic cylinder.

3.Hydraulic cylinder 3-1/2"

5.Transport lock-up

6.Cylinder spacers

7.Ratchet (optional)

8.SMV Mounting bracket

9.SMV Socket

10.SMV Bracket

11.SMV Emblem

18.Clevis pin, 1" x 4.58"

19.Clevis pin, 1" x 5.08"

22.1/4 NPT x 1/4 NPT x 156" Hose

23.1/4 NPT x 1/4 NPT Elbow, restricted

24.1/2 NPT x 1/4 NPT Reducer bushing

35.5/16 NC Lock nut

36.5/16 NC x 1/2 Carriage bolt

38.1/4 NC x 1/2 Round head screw

39.1/4 NC Hex nut

53. 1/2 NC Lock nut

63. Cotter pin, 1/4" x 1-1/2"

67. 1/2 NC x 1-1/2 Carriage bolt

Figure 24. Spring Arm and Cylinder Installation

34 Assembly

MAN0764 (11/5/2008)

 

 

Image 34
Contents MAN0764 Introduction To the DealerTable of Contents BW1620X, BW1620XQ SpecificationsGeneral Information BW2400X, BW2400XQFree Mower Safety Video SafetyTraining Package for Rotary Mowers/Cutters-English Training Package for Rotary Mowers/Cutters-English/SpanishTraining Safety RulesInstallation PreparationTransportation OperationMaintenance Storage Be Careful Safety & Instructional DecalsPN 1006348 located on split rim wheels Safety Safety Operation Connecting Cutter to TractorOperation Interference Check Cutting Height AdjustmentHydraulic Connection CV Driveline Turning LimitsCutter Operation Attitude Rod Adjustment FigureTractor Operation Cutting Height Normal Mowing WingsShredding Mowing TipsTransporting Lock-UpWing Lock-Up Figure PRE-OPERATION Check ListCenter Section Lock-Up Figure Owner Service Owner ServiceBlocking Method Driveline Lubrication LubricationGearbox Lubrication Description FrequencyBlades Blade Installation FigureSeasonal Lubrication Blade Removal FigureSlip Clutch Adjustment Figure Blade Sharpening FigureCleaning Repairing Rubber ShieldingRepairing Optional Chain Shielding Shielding RepairTroubleshooting TroubleshootingSeal Replacement Figure Dealer ServiceDealer Service Vertical Shaft Seal Replacement FigureWing & Center Gearbox Repair Gearbox Wing & Center Splitter Gearbox Repair Figure Splitter Gearbox Removal Gearbox Installation FigureSplitter Gearbox Disassembly Figure Center ShaftSplitter Gearbox Inspection Splitter Gearbox Assembly FigureSplitter Gearbox Installation Side ShaftCrossbar Removal Crossbar RemovalJoint Disassembly Crossbar InstallationUniversal Joint Repair Joint Assembly Service Tires SafelyCenter Section Assembly AssemblyAssembly Instructions Install Hydraulic Hoses FigureInstall Attitude Rods Figure Install Height Adjustment CylinderInstall SMV Emblem Figure Install Spring Wheel Arms FigureInstall Tongue Figure Install 3-Joint Drive FigureInstall Optional CV Drive Figure CV Drive InstallationInstall Wing Wing AssemblyInstall Wing Cylinder and Transport Lock Install Wing Wheel Yoke Figure Install Wing Wheel Yoke Adjustment LinkHydraulic Cylinder Fill GearboxesOptional Equipment Tandem Wheel Assembly Installation Center Section Right WingInstall Chain or Belt Shielding Chain Shielding Installation Center SectionLink Winch Kit Installation Optional Roller Assembly InstallationCrossbar Installation Left Wing Shredder Installation OptionalCrossbar Installation Right Wing Crossbar Installation Center SectionBW1620X Counterweight Installation BW1620X Counterweight Installation PRE-DELIVERY Check List Dealer Check ListsDealer Check Lists Delivery Check ListParts Index PartsMain Frame Assembly Front Section Part Main Frame Assembly Rear Section 1027070 Center wheel yoke 57050 Access hole cover 10475 Right Wing Shown Part QTY Description Wing & Center Gearbox Assembly 540 RPM 1000 RPM Wing CenterSplitter Gearbox Assembly 540 RPMCenter Deck Drive Assembly Front 3-JOINT Drive Assembly Equal Angle 40728 Inner shieldRear 3-JOINT Drive Assembly Equal Angle Type a 540 RPM Front CV Drive Type B 540 RPM Front CV Drive Type a 1000 RPM Front CV Drive RPM 1-3/8 21-Splined RPM 1-3/4 20-SplinedType B 1000 RPM Front CV Drive Wing Drive Assembly REF Part QTY DescriptionBolt Wheel & Tire Assembly Rubber Shielding Center Section Standard on BW2400 Models Rubber Shielding Wing Standard on BW2400 Models Chain Shielding Center Section Single ROW Double ROWChain Shielding Wing Tandem Axle Wheel Yoke Optional Parts Hydraulic CylindersHydraulic Cylinder Stroke Control KIT Crossbar Puller OptionalShredder KIT Optional BW1620X / BW1620XQ / BW1620XQREV Counterweight BOX Assembly Winch KIT Optional Winch Kit OperationAppendix Bolt Torque ChartSAE Series Torque Chart Metric SeriesBolt Size Chart AbbreviationsIndex IndexWarranty South Illinois Route Post Office Box Oregon, Illinois

BW2400X, BW1620XQREV, BW2400XQ, BW1620X, BW1620XQ specifications

Woods Equipment has established itself as a trusted name in the landscape and agricultural equipment sector, offering a wide range of high-performance products tailored to meet various needs. Among its standout offerings are the BW1620XQ, BW1620X, BW2400XQ, BW1620XQREV, and BW2400X models, known for their robust design and exceptional functionality.

The BW1620XQ is designed for efficient brush cutting, making it an ideal choice for land maintenance and clearing dense underbrush. One of its main features is the heavy-duty construction, which ensures durability even under the toughest conditions. This model is equipped with a reinforced deck, providing added strength and longevity. It also features a powerful PTO-driven cutting system, allowing it to tackle tough growth with ease.

The BW1620X model offers similar capabilities to the BW1620XQ but is optimized for lighter tasks and smaller properties. It shines in residential applications, where maneuverability and ease of use are paramount. This model is lightweight and easy to attach, making it a favorite among homeowners who require a reliable tool for maintaining their yards and gardens.

For those requiring larger-scale solutions, the BW2400XQ provides increased cutting width and efficiency. This model excels in farm and large property applications, where speed and power are essential. Featuring advanced blade technology, the BW2400XQ offers superior cutting performance and reduced maintenance needs. Additionally, it boasts adjustable height settings, allowing users to customize their cutting experience based on the terrain and type of vegetation.

The BW1620XQREV is a revolutionary model that incorporates newer technology for even better performance and user experience. This model offers enhanced features such as improved blade design for finer cuts and an innovative quick-attach system that enables fast connectivity and disconnection from tractors.

Finally, the BW2400X model is the standard version of the BW2400XQ, providing similar power and efficiency without some of the specialized features, making it a cost-effective solution for users who need reliable equipment without as many bells and whistles.

In conclusion, Woods Equipment's BW1620XQ, BW1620X, BW2400XQ, BW1620XQREV, and BW2400X models each feature unique characteristics tailored to specific applications, ensuring users can find the right tool for their needs, whether for residential landscaping or large-scale agricultural tasks. Their emphasis on durability, efficiency, and user-friendly design makes them a preferred choice across various sectors.