Yazoo/Kees ZEKH52240, ZEKH48240, ZEKH42200 manual Remove blade bolt by turning counterclockwise

Page 49

MAINTENANCE

Blade replacement:

WARNING!

Blades are sharp. Protect your hands with gloves and/or wrap blades with a heavy cloth when handling.

•Remove blade bolt by turning counterclockwise.

IMPORTANT INFORMATION

To ensure proper assembly, center hole in blade must align with star on cutter housing.

•Install new or re-sharpened blade with stamped "GRASS SIDE" facing towards ground/grass (down) or “THIS SIDE UP” facing deck and cutter housing.

•Install and tighten blade bolt securely.

Torque blade bolt to 45-55 ft/lbs (60-75 Nm).

IMPORTANT INFORMATION Special blade bolt is heat treated.

Replace with a Yazoo/Kees bolt if required.

Do not use lower grade hardware than specified.

8011-671

1.Blade

2.Center hole

3.Star

4.Cutter housing

5.Blade bolt (special) Blade attachment, principal

English-47

Image 49

Contents Operator’s manual Page OPERATOR’S Manual ZE Rider ContentsEnglish-2 Introduction IntroductionManufacturing Number Good ServiceSymbols and Decals Symbols and DecalsXxxx xxxxxx Repair work Safety Instructions Safety InstructionsGeneral Operation English-8 Slope Operation Personal Safety EquipmentChildren Maintenance General Maintenance Risk of sparking Important Information TransportCustomer responsibilities Controls ControlsMotion Control Levers Parking Brake Seat adjustment boltsTracking Fuel Shut Off ValveRefueling Fuses By pass linkageHour Meter Ignition SwitchChoke Control USE Full Throttle When Mowing , for Blade switchThrottle Control Cutting height pedal AccessoriesOperation OperationTraining Starting the Engine Before StartingDepress the control for disengaging the mower deck Set the choke control USE Full Throttle When Mowing To remove cables, reverse order To start an engine with a weak batteryRunning Operating on hills Mowing Tips Stopping the Engine Moving by Hand Maintenance MaintenanceMaintenance Schedule Nance Once Each Maintenance Before After 100 To clean battery and terminals BatteryReplacing battery Always use protective glasses when handling the batteryIgnition System Checking the Safety System Checking and Adjusting the Choke Cable Checking and Adjusting the Throttle CableChecking the Engines Cooling Air Intake Replacing the Air Filter ServiceStandard air filter Checking the Fuel Pump’s Air Filter Replacing the Fuel FilterChecking Tire Pressures Checking the V-belts Checking the Parking BrakeDeck belt To replace deck beltDeck belt installation IZT belt removal IZT beltChecking the Blades Belt installationRemove blade bolt by turning counterclockwise Adjusting Cutting Height Adjusting the Mower DeckLeveling To adjust anti-scalp rollers Use protective glasses when cleaning and washing Cleaning and WashingRemoval and installation of caster wheel Caster WheelsTo adjust parking brake Tracking adjustmentMower is tracking to the right Mower is tracking to the leftLubrication LubricationLubrication Schedule Change transaxles transmission filtersLubricating in Accordance with the Lubrication Schedule Lubricating the CablesFront Wheel Mount Front Wheel BearingsEngine Oil Changing the Engine Oil Deck outer spindleChecking the Oil Level Transaxle Transmission Fluid Change Changing the Engine Oil FilterExpansion Tank Purging Procedures Trouble Shooting Guide Trouble Shooting GuideProblem Cause English-60 English-61 Storage ServiceStorage Winter StorageWiring diagram Wiring DiagramsTechnical Data Technical DataZEKH42200/968999694 ZEKH48240/968999698 Productivity ZEKH52240/968999701 625 lbs Torque Specifications Conformity Certificates Conformity CertificatesUSA requirements Service Journal Service JournalDelivery Service Action Date, mtr reading, stamp, signAfter the First 5-8 Hours Action Hour ServiceEnglish-73 English-74 English-75 English-76 Page 530 131340IR 07/31/07