Yazoo/Kees ZEKH48240, ZEKH52240, ZEKH42200 manual Checking the Oil Level

Page 57

LUBRICATION

Checking the Oil Level

Check the oil level in the engine when the machine is standing level and the engine is stopped.

Remove the dipstick, wipe it clean, and then replace it.

The dipstick should be screwed into place.

Take the dipstick out again and read the oil level.

The oil level should lie between the markings on the dipstick. If the level is approaching the ”ADD” mark, fill the oil to the ”FULL” mark on the dipstick.

Never fill to above the ”FULL” mark.

The oil is filled through the hole for the dipstick.

API class SF, SG, SH, SJ or higher must be used. Syntetic oil SAE 5W-30 or 10W-30 is recommended at all temperatures. Mineral oil SAE 5W-30, 10W-30 can be used between -18 °C/0 °F and +5 °C/40 °F. At temperature above +5 °C/40 °F single grade SAE 30 must be used.

The engine holds 0.88 qt (1.0 liters) of oil excluding the filter, including filter 2 qt (1.9 liters).

8011-500

Remove the dipstick

8009-159

The dipstick markings

English-55

Image 57

Contents Operator’s manual Page OPERATOR’S Manual ZE Rider ContentsEnglish-2 Introduction IntroductionManufacturing Number Good ServiceSymbols and Decals Symbols and DecalsXxxx xxxxxx Repair work Safety Instructions Safety InstructionsGeneral Operation English-8 Slope Operation Personal Safety EquipmentChildren Maintenance General Maintenance Risk of sparking Important Information TransportCustomer responsibilities Controls ControlsMotion Control Levers Parking Brake Seat adjustment boltsTracking Fuel Shut Off ValveRefueling Fuses By pass linkageIgnition Switch Hour MeterChoke Control Blade switch USE Full Throttle When Mowing , forThrottle Control Cutting height pedal AccessoriesOperation OperationTraining Starting the Engine Before StartingDepress the control for disengaging the mower deck Set the choke control USE Full Throttle When Mowing To remove cables, reverse order To start an engine with a weak batteryRunning Operating on hills Mowing Tips Stopping the Engine Moving by Hand Maintenance MaintenanceMaintenance Schedule Nance Once Each Maintenance Before After 100 To clean battery and terminals BatteryReplacing battery Always use protective glasses when handling the batteryIgnition System Checking the Safety System Checking and Adjusting the Throttle Cable Checking and Adjusting the Choke CableChecking the Engines Cooling Air Intake Service Replacing the Air FilterStandard air filter Replacing the Fuel Filter Checking the Fuel Pump’s Air FilterChecking Tire Pressures Checking the V-belts Checking the Parking BrakeDeck belt To replace deck beltDeck belt installation IZT belt removal IZT beltChecking the Blades Belt installationRemove blade bolt by turning counterclockwise Adjusting the Mower Deck Adjusting Cutting HeightLeveling To adjust anti-scalp rollers Use protective glasses when cleaning and washing Cleaning and WashingRemoval and installation of caster wheel Caster WheelsTo adjust parking brake Tracking adjustmentMower is tracking to the right Mower is tracking to the leftLubrication LubricationLubrication Schedule Change transaxles transmission filtersLubricating in Accordance with the Lubrication Schedule Lubricating the CablesFront Wheel Mount Front Wheel BearingsEngine Oil Changing the Engine Oil Deck outer spindleChecking the Oil Level Transaxle Transmission Fluid Change Changing the Engine Oil FilterExpansion Tank Purging Procedures Trouble Shooting Guide Trouble Shooting GuideProblem Cause English-60 English-61 Storage ServiceStorage Winter StorageWiring diagram Wiring DiagramsTechnical Data Technical DataZEKH42200/968999694 ZEKH48240/968999698 Productivity ZEKH52240/968999701 625 lbs Torque Specifications Conformity Certificates Conformity CertificatesUSA requirements Service Journal Service JournalDelivery Service Action Date, mtr reading, stamp, signAfter the First 5-8 Hours Action Hour ServiceEnglish-73 English-74 English-75 English-76 Page 530 131340IR 07/31/07