Guardian Technologies 02010-2, 04164-3 owner manual ‹ 2.5.2 Some Important Considerations

Page 31

Section 2 – Installation

Recreational Vehicle Generator

Figure 2.15 – Typical Propane Gas Fuel System

‹ 2.5.4 PRIMARY REGULATOR

‹2.5.2 SOME IMPORTANT CONSIDERATIONS

When installing an LP gas system, consider seriously the following items:

•All fittings, lines, hoses and clamps must be tight and free of leaks. Apply a pipe sealant to threads when assembling threaded connections. This reduces the possibility of leakage.

•Test the entire fuel system for leaks using approved test methods.

•Optimum gas pressure at the inlet to the gaseous fuel solenoid valve and secondary regulator is 11 inches water column.

•The installer’s fuel supply connection point is at the gaseous fuel solenoid valve. This is a 3/4-inch (female) connection. Provide a suitable 3/4-inch NPT (male) connector to attach to the fuel supply line.

•Use a length of approved flexible fuel hose between the gaseous fuel solenoid valve and rigid gas pip- ing. The flexible line should be at least six (6) inches longer than necessary.

‹2.5.3 VAPOR WITHDRAWAL

LP gas is stored in pressure tanks as a liquid. The gas systems used with these generators were designed only for vapor withdrawal type systems. Vapor with- drawal systems use the gas vapors that form above the liquid fuel in the tank. Do NOT attempt to use the generator with any liquid withdrawal type system.

Gas pressure delivered to the solenoid valve must be properly regulated by means of a primary gas regu- lator. Mount the primary regulator at the gas tank outlet or in the supply line from the gas tank. The following rules apply:

•For best results, the primary regulator supplies gaseous fuel to the secondary regulator at 11 inches water column. Do NOT exceed 14 inches water column.

•The installer must be sure the primary regulator is rated at sufficient gas flow to operate the generator plus all other gas appliances in the circuit.

NOTE:

Recommended MINIMUM gas flow rate for all air- cooled generators is 67 cubic feet per hour.

If an existing primary gas regulator does not have a sufficient flow capacity for the generator and other gas appliances in the circuit, (a) install a primary regulator with adequate flow rate, or (b) install a separate regulator only and rated at least 67 cubic feet per hour. The inlet side of any pri- mary regulator that supplies the generator must connect directly to a gas pressure tank. Do NOT tee the generator line into a gas circuit feeding other areas.

‹2.5.5 GASEOUS CARBURETION

LP gas vapors should be supplied to the secondary regulator inlet at about 11 inches water column (posi- tive pressure). The engine pistons draw air in dur- ing the intake stroke (Figure 2.16). This air passes through a carburetor venturi, which creates a low pressure that is proportional to the quantity of air being pumped. The low pressure from the carburetor venturi acts on the regulator diaphragm to pull the diaphragm toward the source of low pressure. A lever attached to the diaphragm opens a valve to permit gas glow through the carburetor.

Figure 2.16 – LP Gas Carburetion Diagram

29

Page 30 Page 32
Image 31
Page 30 Page 32
Contents Air-cooled Recreational Vehicle Generators Introduction Authorized Service Dealer LocationInside Front Cover Part II Installation Instructions Warning   Electrical Hazards  Model Generator IdentificationGenerator AC Connection System SafetySpecifications Generator Applicability‹ 1.5.6 Generator ‹ 1.5.2 Optional Propane Fuel System‹ 1.5.3 Fuel Consumption ‹ 1.5.4 Engine OIL RequirementsOptional Remote START/STOP Panel Generator Control PanelAutomatic Choke Gasoline only Starting the Generator Before Starting the EngineStopping the Generator SUMMER/WINTER Heat Riser System‹ 2.7.1 Letting the Engine Stabilize ‹ 2.8.1 do not Overload the Generator ‹ 2.9. LOW OIL Pressure Switch‹ 2.9.2 High Temperature Switch Protection SystemsChecking the Engine OIL Level Additional Information‹ 2.10.2 Operation in High Grass or Brush ‹ 3.3.1 Cleaning the Foam Precleaner Maintaining the Engine AIR CleanerChanging the Engine OIL AND/OR OIL Filter Checking the Engine Spark Plug Clean AIR IntakeSpark Arrestor Muffler Cleaning the GeneratorBattery Maintenance Fuel Filter Gasoline onlyExercising the Generator OUT of Service Procedure‹ 3.13.1 Removal from Service Drive Belt‹ 3.13.2 Return to Service Part  General Hazards   Fire Hazards  Standards Booklets Purpose and Scope ManualEquipment Description Generator Engine Operating Speed0F1127 ‹ 2.1.1 Generator Location Location and Support‹ 2.1.2 Generator Support ‹ 2.2.1 Compartment Size Generator Compartments‹ 2.1.4 Generator Restraint ‹ 2.2.2 Compartment Construction‹ 2.2.4 Acoustics ‹ 2.2.3 Sound Insulating MaterialsTypical Noise Abatement ‹ 2.2.5 Compartment Floor Cutouts‹ 2.3.1 Generator Airflow Cooling and Ventilating AIR‹ 2.3.2 Cooling AIR Inlet Openings Gasoline Fuel System ‹ 2.3.4 Testing the Installation‹ 2.3.3 Compensating for Restrictions ‹ 2.4.2 Generator Fuel Supply Line LP GAS Fuel System‹ 2.5.1 Parts not Included in Fuel System ‹ 2.5.3 Vapor Withdrawal ‹ 2.5.2 Some Important Considerations‹ 2.5.5 Gaseous Carburetion ‹ 2.5.8 Leakage Tests Exhaust System‹ 2.5.6 Fuel Supply Lines ‹ 2.5.7 Excess Flow Valve‹ 2.7.1 Electrical Junction BOX ‹ 2.6.3 Exhaust System Safety‹ 2.6.1 Mufflers and Spark Arrestors ‹ 2.6.2 Type of Exhaust System‹ 2.7.3 Generator AC Connections ‹ 2.7.2 Wiring‹ 2.7.7 Ground Fault Circuit Interrupters ‹ 2.7.6 Power Supply CordOptional Accessories Battery InstallationInitial Start Post Installation TestsTesting Under Load Before Initial START-UPInstallation Checklist Problem Cause Correction Troubleshooting GuideElectrical Data Electrical Data Exploded Views and Parts Lists Description Exploded Views and Parts Lists QTY Description Exploded Views and Parts Lists Description QTY Exploded Views and Parts Lists SCROLL, Flywheel Exploded Views and Parts Lists Ring SET, Piston DIA Exploded Views and Parts Lists MANIFOLD, Intake MANUFACTURER’S Emission Control System Warranty Coverage Your Warranty Rights and ObligationsPURCHASER’S/OWNER’S Warranty Responsibilities Emission Related Parts Include the Following Emission Control System WarrantyWarranty Schedule CONSUMER/PERSONAL Applications

02010-2, 04164-3 specifications

Guardian Technologies has made a significant impact in the air purification industry with its range of innovative products, particularly the models 02010-2 and 04164-3. These air purifiers are designed to enhance indoor air quality by leveraging advanced technologies, making them popular choices for both home and office environments.

The Guardian Technologies 02010-2 is an impressive model known for its portable design and effective purification capabilities. It features a 3-in-1 air cleaning system that includes a HEPA filter, a charcoal filter, and a UV-C light. The HEPA filter is essential for capturing allergens such as pollen, dust mites, and pet dander, making it ideal for allergy sufferers. The charcoal filter helps eliminate odors, capturing smoke and volatile organic compounds, while the UV-C light helps reduce germs and bacteria, ensuring a cleaner atmosphere.

This model is compact, allowing it to fit seamlessly into small spaces, while still providing powerful purification performance. With a whisper-quiet operation, it can be used in bedrooms or workspaces without causing disruption. Additionally, it features an adjustable fan speed, enabling users to customize the airflow according to their preference, along with an energy-efficient design that helps reduce power consumption.

On the other hand, the Guardian Technologies 04164-3 introduces a more advanced air purification system with similar foundational features but enhances the user experience with added functionalities. This model typically incorporates a combination of a HEPA filter and a UV-C light as well, but it often boasts smart capabilities. These may include an air quality sensor that helps monitor particulate levels in real-time, automatically adjusting the purification level when needed. This intelligent feature ensures that the air quality remains at optimal levels without requiring constant manual adjustments.

Both models prioritize user convenience, sporting features like filter replacement indicators, ensuring timely maintenance of the purification system. They are designed for ease of use and portability, allowing consumers to move them effortlessly from room to room.

In summary, Guardian Technologies’ models 02010-2 and 04164-3 stand out in the air purifier market due to their advanced filtration systems, ease of use, and smart technologies. These air purifiers are key investments for anyone looking to improve their indoor air quality effectively.
Top Page Image Contents