Great Dane GSRKA1934S manual Service Intervals, Mowing Travel Speeds, Servicing Engine

Page 20

SERVICE INTERVALS

Use a travel speed that fits the conditions:

Mow tall or wet grass twice. Cut grass at half desired height – then cut at desired height.

Travel slow when mowing tall, thick or wet grass.

Avoid damaging grass by slipping or skidding machine drive wheels. Practice smooth control lever movements.

When performing sharp turns, do not allow inside ma- chine drive wheel to stop and twist on grass.

Mowing Travel Speeds

Use slow travel speeds for:

Slopes.

Trimming.

Close quarters.

Tall grass.

Use faster travel speeds for:

Normal mowing on level ground.

CAUTION: Avoid injury! Help prevent serious injury. Keep hands and feet away from blades and the discharge opening.

Do not step on either side of the mower deck when mounting and dismounting the machine. Mount and dismount the machine using the front foot plate.

1.Park machine on a hard, level surface.

2.Disengage PTO.

3.Move motion control levers to the neutral position.

4.Lock park brake.

5.Stop engine and remove key. Wait for mower blades to stop turning before leaving operator’s position.

Service Intervals

Servicing Your Machine

IMPORTANT: Avoid Damage! Operating in extreme condi- tions may require more frequent service intervals:

Engine components may become dirty or plugged when operating in extreme heat, dust or other se- vere conditions.

Engine oil may lose efficiency if vehicle is operated constantly at slow or low engine speeds or with frequent short trips.

Please use the following timetables to perform routine maintenance on your machine.

Servicing Engine

See engine manufacturer’s owner’s manual provided with your machine for engine service information.

Break-In (After First 10 Hours)

Check air pressure in tires.

Check wheel bolt torque.

Check and adjust park brake.

Change engine oil and filter.

Check mower deck drive belt tension.

Check hydraulic pump drive belt.

Check transmission neutral adjustment.

Every 40 Hours

Check air pressure in tires.

Check wheel bolt torque.

Check and adjust park brake.

Change engine oil and filter.

Check foam and paper air cleaner elements.

Clean engine shrouds as needed.

Lubricate front caster spindles and wheels.

Lubricate mower deck idler pivot.

Check mower deck drive belt tension.

Lubricate hydraulic pump idler pivot.

Check hydraulic pump drive belt.

Check hydraulic fluid level.

If operating machine in extremely dusty or dirty conditions:

Clean behind engine shrouds and exposed fins.

Remove screws on blower fan screen and clean behind.

Every 100 Hours

Lubricate mower deck spindles.

Clean and gap spark plugs.

Check hydraulic pump drive belt.

Clean behind engine shrouds and exposed fins.

Remove screws on blower fan screen and clean behind.

Every 500 Hours

• Change hydraulic oil and filter.

Yearly

Change fuel filter.

Clean battery.

Change engine oil and filter at least once per season.

Change hydraulic oil and filter at least once per season.

Replace spark plugs.

SERVICE INTERVALS- 18

Image 20
Contents Great Dane GSRKA1934S Page Introduction Special MessagesSafety Labels Safety LabelsSafety-Alert Symbol Safety LabelsSafety Labels Safety SafetyChecking Mowing Area Using a Spark ArrestorOperating Safely Avoid Tipping Parking SafelyMaintenance and Storage Keep Riders OffAvoid High Pressure Fluids Checking Wheel HardwareTire Safety Prevent FiresHandling Fuel Safely Handling Waste Product and ChemicalsOperating OperatingAvoid Damage to Plastic and Painted Surfaces Operator Station ControlsRaising and Lowering Thigh Pad Adjusting Cutting HeightMounting and Dismounting Machine Safely Caster to deck mounting Lower Positon Setting Cutting HeightCaster to deck mounting Upper Positon Testing PTO Switch Testing Park Brake SwitchTesting Neutral Switch Start Testing Safety SystemsTesting the Park Brake Using the PTO Using Park BrakeUsing the Throttle Locking Park BrakeUsing the Hourmeter Using the Motion Control LeversForward and Reverse Motion Neutral PositionForward Gentle Right TurnReverse Sharp Left TurnStarting Engine Engaging MowerUsing Pump Free-Wheel Valves Stopping the EngineTransporting Machine on a Trailer Mowing TipsService Intervals Service IntervalsMowing Travel Speeds Servicing EngineService Engine Service LubricationLubricating Mower Deck Spindles Lubricating Mower Deck Idler PivotService Engine Engine OilChecking Engine Oil Level Changing Engine Oil and FilterCleaning Engine Air Intake Screen and Fan Checking and Cleaning Air Filter ElementsService Transmission Replacing Fuel FilterService Transmission Checking Hydraulic Oil LevelChanging Hydraulic Oil and Filter Hydraulic OilCleaning Hydraulic Oil Pump Cooling Fins Removing Traction Drive BeltChecking Motion Control Linkages Installing Traction Drive BeltChecking and Adjusting Motion Control Linkages Adjusting Motion Control Return to Neutral RTN Linkages Checking and Adjusting Transmission TrackingAdjust Neutral Switch Service Steering and BrakesAdjusting Forward and Reverse Speeds Service Mower Service Steering & BrakesService Mower Adjusting Park Brake Testing Park BrakeAdjusting Drive Belt Tension Installing Mower Deck Drive BeltReplacing Mower Deck Drive Belt Removing Mower Deck Drive BeltChecking for Bent Mower Blades Checking and Replacing Mower BladesService Electrical Service Electrical Service the Battery SafelySharpening Blades Balancing BladesInstalling Checking the Battery Sealed BatteriesRemoving and Installing Battery Service Miscellaneous Using Booster BatteryCleaning Battery and Terminals Replacing FuseAdjusting Operator Presence Switch Service MiscellaneousUsing Proper Fuel Filling Fuel TankRemoving and Installing Rear Drive Wheels Removing and Installing Front Caster WheelsTightening Rear Drive Wheel Hardware RemovingChecking Tire Pressure Servicing Caster Wheel Roller BearingsTroubleshooting Cleaning and Repairing Plastic SurfacesCleaning and Repairing Metal Surfaces TroubleshootingStorage Electrical SystemMower Deck MachinePark Brake Assembly StoragePreparing Machine for Storage Preparing Fuel and Engine For StorageSpecifications Assembly Connect HandlesCheck Hydraulic Oil Level Removing Machine From StorageGetting Quality Service Great Dane Quality Continues with Quality Service Part NumberWiring Diagram Wiring DiagramHydraulic Schematic Hydraulic SchematicPage Main Frame Assembly QTY Description Hydraulic and Handle Assembly QTY Description ENGINE, Hydraulic and Mainframe Assembly HOSE, 3/8 SAE30R7 Fuel & OIL Foot PLATE/CONSOLE Components Console ComponentsPLATE, Platform TAB LH Deck Assembly PULLEY, Flat 5.0X.38 W/BRG Wheel and Strut ASSEMBLY/PUMP Components WHEEL, Front 11X4X5 SLV Mist Spindle Assembly Spindle Assembly Decal Locations D18197 M117554