Great Dane GSRKA1934S manual Installing Traction Drive Belt, Checking Motion Control Linkages

Page 27

SERVICE TRANSMISSION

BA

3.Remove two cap screws (A).

4.Remove rear shield (B).

CAUTION: Avoid injury! Tensioning spring is under high tension. Wear gloves and safety glasses, and use a spring puller to install and remove spring.

G

D

E C

4 ⅝” - 5”

F

Picture Note: Traction drive belt idler pulley bottom view.

5.Insert 3/8 in. breaker bar into hole (C) and rotate idler pulley (D) forward to ease tension on traction drive belt.

6.Remove traction drive belt (E).

Installing Traction Drive Belt:

NOTE: Install the traction drive belt (E) in front of an- chor cap screw (F).

G

D

E C

4 ⅝” - 5”

F

1.Install traction drive belt (E) on drive sheaves (G) as shown. Ensure that traction drive belt is positioned in front of anchor cap screw (F).

2.Insert 3/8 in. breaker bar into hole (C) and rotate idler pulley (D) forward for additional clearance to install traction drive belt.

3.Install rear shield.

4.Install mower deck drive belt.

Checking and Adjusting Motion Control Linkages

CAUTION: Avoid injury! Engine exhaust fumes contain carbon monoxide and can cause seri- ous illness or death.

Move the machine to an outside area before running the engine.

Do not run an engine in an enclosed area without adequate ventilation.

Connect a pipe extension to the engine ex- haust pipe to direct the exhaust fumes out of the area.

Allow fresh outside air into the work area to clear the exhaust fumes out.

NOTE: Check and adjust motion control linkages with the machine parked on a hard, level surface.

Checking Motion Control Linkages:

1.1. Park machine safely. (See Parking Safely in the SAFETY section.)

SERVICE TRANSMISSION- 25

Image 27
Contents Great Dane GSRKA1934S Page Special Messages IntroductionSafety Labels Safety LabelsSafety Labels Safety-Alert SymbolSafety Labels Safety SafetyUsing a Spark Arrestor Operating SafelyChecking Mowing Area Parking Safely Avoid TippingChecking Wheel Hardware Maintenance and StorageKeep Riders Off Avoid High Pressure FluidsHandling Waste Product and Chemicals Tire SafetyPrevent Fires Handling Fuel SafelyOperator Station Controls OperatingOperating Avoid Damage to Plastic and Painted SurfacesAdjusting Cutting Height Mounting and Dismounting Machine SafelyRaising and Lowering Thigh Pad Setting Cutting Height Caster to deck mounting Upper PositonCaster to deck mounting Lower Positon Testing Safety Systems Testing PTO SwitchTesting Park Brake Switch Testing Neutral Switch StartLocking Park Brake Testing the Park Brake Using the PTOUsing Park Brake Using the ThrottleNeutral Position Using the HourmeterUsing the Motion Control Levers Forward and Reverse MotionSharp Left Turn ForwardGentle Right Turn ReverseEngaging Mower Starting EngineMowing Tips Using Pump Free-Wheel ValvesStopping the Engine Transporting Machine on a TrailerServicing Engine Service IntervalsService Intervals Mowing Travel SpeedsLubricating Mower Deck Idler Pivot Service EngineService Lubrication Lubricating Mower Deck SpindlesChanging Engine Oil and Filter Service EngineEngine Oil Checking Engine Oil LevelChecking and Cleaning Air Filter Elements Cleaning Engine Air Intake Screen and FanReplacing Fuel Filter Service TransmissionHydraulic Oil Service TransmissionChecking Hydraulic Oil Level Changing Hydraulic Oil and FilterRemoving Traction Drive Belt Cleaning Hydraulic Oil Pump Cooling FinsInstalling Traction Drive Belt Checking and Adjusting Motion Control LinkagesChecking Motion Control Linkages Checking and Adjusting Transmission Tracking Adjusting Motion Control Return to Neutral RTN LinkagesService Steering and Brakes Adjusting Forward and Reverse SpeedsAdjust Neutral Switch Adjusting Park Brake Testing Park Brake Service MowerService Steering & Brakes Service MowerRemoving Mower Deck Drive Belt Adjusting Drive Belt TensionInstalling Mower Deck Drive Belt Replacing Mower Deck Drive BeltChecking and Replacing Mower Blades Checking for Bent Mower BladesBalancing Blades Service ElectricalService Electrical Service the Battery Safely Sharpening BladesChecking the Battery Sealed Batteries Removing and Installing BatteryInstalling Replacing Fuse Service MiscellaneousUsing Booster Battery Cleaning Battery and TerminalsFilling Fuel Tank Adjusting Operator Presence SwitchService Miscellaneous Using Proper FuelRemoving Removing and Installing Rear Drive WheelsRemoving and Installing Front Caster Wheels Tightening Rear Drive Wheel HardwareServicing Caster Wheel Roller Bearings Checking Tire PressureTroubleshooting TroubleshootingCleaning and Repairing Plastic Surfaces Cleaning and Repairing Metal SurfacesElectrical System StorageMachine Park BrakeMower Deck Preparing Fuel and Engine For Storage AssemblyStorage Preparing Machine for StorageRemoving Machine From Storage SpecificationsAssembly Connect Handles Check Hydraulic Oil LevelGetting Quality Service Part Number Great Dane Quality Continues with Quality ServiceWiring Diagram Wiring DiagramHydraulic Schematic Hydraulic SchematicPage Main Frame Assembly QTY Description Hydraulic and Handle Assembly QTY Description ENGINE, Hydraulic and Mainframe Assembly HOSE, 3/8 SAE30R7 Fuel & OIL Console Components Foot PLATE/CONSOLE ComponentsPLATE, Platform TAB LH Deck Assembly PULLEY, Flat 5.0X.38 W/BRG Wheel and Strut ASSEMBLY/PUMP Components WHEEL, Front 11X4X5 SLV Mist Spindle Assembly Spindle Assembly Decal Locations D18197 M117554