Great Dane GSRKA1934S manual Storage, Electrical System

Page 40

STORAGE

Engine Will Not Start

• Park brake lever not in the proper

Or Is Hard To Start

position.

 

• OPC switch not depressed. Stand

 

on platform or adjust switch.

 

• Check that motion control levers

 

are in neutral and neutral

 

switches are correctly adjusted.

 

• PTO engaged.

 

• Stale or improper fuel/fuel level.

 

• Plugged fuel filter.

 

• Plugged air intake filter.

 

• Spark plug wires loose or

 

disconnected.

 

• Spark plugs not gapped correctly.

 

• Blown fuse.

 

• Electrical problem – dead battery.

 

• Choke adjusted incorrectly. See

 

your authorized dealer.

Engine Will Not Slow

• Carburetion problems. See your

Idle

authorized dealer.

 

• Bent or kinked throttle cable.

 

• Bent governor control.

 

• Incorrect governor idle control.

Engine Runs Rough

• Plugged fuel filter.

or Stalls

 

 

• Plugged air intake system.

 

• Fuel cap vent dirty.

 

• Stale or improper fuel/fuel level.

 

• Spark plugs not gapped correctly.

 

• Replace spark plugs.

 

• Choke adjusted incorrectly. See

 

your authorized dealer.

Engine Knocks

• Engine oil level low.

 

• Reduce load. (Slower ground

 

speed.)

 

• Fuel is bad. Fill tank with fresh

 

fuel, correct octane.

 

• Idle speed too slow.

Engine Overheats

• Clean cooling fins.

 

• Low oil level.

 

• Do not operate at slow idle.

 

Operate at fast idle.

 

• Cooling air intake screen is dirty.

 

• Plugged carburetor air intake

 

filter.

 

• Plugged air intake filter.

 

• Operating at too fast ground

 

speed for conditions.

Engine Lacks Power

• Reduce load.

 

• Plugged air intake system.

 

• Plugged fuel filter.

 

• Improper type of fuel. Drain tank

 

and fill with correct fuel.

 

• Clean cooling fins to help prevent

 

overheating.

 

• Replace spark plugs.

Engine Uses Too

• Find and correct oil leaks.

Much Oil

 

 

• Incorrect engine oil.

 

• Plugged oil filter.

 

• Plugged air intake filter.

 

• Worn engine components.

Engine Backfires

• Throttle lever should be at low

Through Muffler

idle for thirty seconds before

 

turning off machine.

High Fuel

• Improper type of fuel.

Consumption

 

 

• Plugged air intake system.

 

• Operating at too fast ground

 

speed for conditions.

 

• Improper valve clearance. See

 

your authorized dealer.

 

• Restricted air intake system.

Other Symptoms

• See engine manufacturer’s

 

owner’s manual provided with

 

your machine for additional

 

information.

Electrical System

IfCheck

Starter Will Not Work • Blown fuse.

OPC Switch faulty or not adjusted properly.

Park brake switch is faulty.

Loose or corroded battery connections.

STORAGE - 38

Image 40
Contents Great Dane GSRKA1934S Page Introduction Special MessagesSafety Labels Safety LabelsSafety-Alert Symbol Safety LabelsSafety Labels Safety SafetyOperating Safely Using a Spark ArrestorChecking Mowing Area Avoid Tipping Parking SafelyMaintenance and Storage Keep Riders OffAvoid High Pressure Fluids Checking Wheel HardwareTire Safety Prevent FiresHandling Fuel Safely Handling Waste Product and ChemicalsOperating OperatingAvoid Damage to Plastic and Painted Surfaces Operator Station ControlsMounting and Dismounting Machine Safely Adjusting Cutting HeightRaising and Lowering Thigh Pad Caster to deck mounting Upper Positon Setting Cutting HeightCaster to deck mounting Lower Positon Testing PTO Switch Testing Park Brake SwitchTesting Neutral Switch Start Testing Safety SystemsTesting the Park Brake Using the PTO Using Park BrakeUsing the Throttle Locking Park BrakeUsing the Hourmeter Using the Motion Control LeversForward and Reverse Motion Neutral PositionForward Gentle Right TurnReverse Sharp Left TurnStarting Engine Engaging MowerUsing Pump Free-Wheel Valves Stopping the EngineTransporting Machine on a Trailer Mowing TipsService Intervals Service IntervalsMowing Travel Speeds Servicing EngineService Engine Service LubricationLubricating Mower Deck Spindles Lubricating Mower Deck Idler PivotService Engine Engine OilChecking Engine Oil Level Changing Engine Oil and FilterCleaning Engine Air Intake Screen and Fan Checking and Cleaning Air Filter ElementsService Transmission Replacing Fuel FilterService Transmission Checking Hydraulic Oil LevelChanging Hydraulic Oil and Filter Hydraulic OilCleaning Hydraulic Oil Pump Cooling Fins Removing Traction Drive BeltChecking and Adjusting Motion Control Linkages Installing Traction Drive BeltChecking Motion Control Linkages Adjusting Motion Control Return to Neutral RTN Linkages Checking and Adjusting Transmission TrackingAdjusting Forward and Reverse Speeds Service Steering and BrakesAdjust Neutral Switch Service Mower Service Steering & BrakesService Mower Adjusting Park Brake Testing Park BrakeAdjusting Drive Belt Tension Installing Mower Deck Drive BeltReplacing Mower Deck Drive Belt Removing Mower Deck Drive BeltChecking for Bent Mower Blades Checking and Replacing Mower BladesService Electrical Service Electrical Service the Battery SafelySharpening Blades Balancing BladesRemoving and Installing Battery Checking the Battery Sealed BatteriesInstalling Service Miscellaneous Using Booster BatteryCleaning Battery and Terminals Replacing FuseAdjusting Operator Presence Switch Service MiscellaneousUsing Proper Fuel Filling Fuel TankRemoving and Installing Rear Drive Wheels Removing and Installing Front Caster WheelsTightening Rear Drive Wheel Hardware RemovingChecking Tire Pressure Servicing Caster Wheel Roller BearingsTroubleshooting Cleaning and Repairing Plastic SurfacesCleaning and Repairing Metal Surfaces TroubleshootingStorage Electrical SystemPark Brake MachineMower Deck Assembly StoragePreparing Machine for Storage Preparing Fuel and Engine For StorageSpecifications Assembly Connect HandlesCheck Hydraulic Oil Level Removing Machine From StorageGetting Quality Service Great Dane Quality Continues with Quality Service Part NumberWiring Diagram Wiring DiagramHydraulic Schematic Hydraulic SchematicPage Main Frame Assembly QTY Description Hydraulic and Handle Assembly QTY Description ENGINE, Hydraulic and Mainframe Assembly HOSE, 3/8 SAE30R7 Fuel & OIL Foot PLATE/CONSOLE Components Console ComponentsPLATE, Platform TAB LH Deck Assembly PULLEY, Flat 5.0X.38 W/BRG Wheel and Strut ASSEMBLY/PUMP Components WHEEL, Front 11X4X5 SLV Mist Spindle Assembly Spindle Assembly Decal Locations D18197 M117554