Great Dane GSRKA1934S Specifications, Check Hydraulic Oil Level, Removing Machine From Storage

Page 43

SPECIFICATIONS

NOTE: The stored battery should be recharged every 90 days.

10. Charge the battery.

Check Hydraulic Oil Level

IMPORTANT: Avoid Damage! Prolonged exposure to sunlight could damage the hood surface. Store ma- chine inside or use a cover if stored outside.

11.Store the vehicle in a dry, protected place. If vehicle is stored outside, put a waterproof cover over it.

Removing Machine From Storage

A

B

1.Check tire pressure.

2.Check engine oil level.

3.Check battery electrolyte level, if your battery is not maintenance free. Charge battery if necessary.

4.Install battery.

5.On gas engines: Check spark plug gap. Install and tighten plugs to specified torque.

6.Lubricate all grease points.

7.Open fuel shut-off valve, if your machine is equipped.

8.Run the engine 5 minutes without the mower or any at- tachments running to allow oil to be distributed through- out engine.

9.Be sure all shields and guards or deflectors are in place.

Assembly

Connect Handles

The handles are disconnected and rotated forward dur- ing assembly to allow for proper fitment into the shipping container.

1. Rotate the handles up.

B

A

C

2.Connect the pump control arm (C) to the handle weldment by inserting the adjustment block (A) into the handle weldment and securing with the hairpin clip (B).

3.Set the speed control bar to desired speed and lock.

1.Clean area around dipstick cap (A).

2.Remove dipstick cap (A). Wipe dipstick clean.

NOTE: Do not tighten dipstick cap when checking oil level.

3.Insert dipstick in filler neck (B). Do not tighten cap.

4.Remove dipstick. Check oil level on dipstick. Oil level should be between the ADD and FULL marks on dip- stick.

If oil is level is below ADD mark, fill to proper level.

If oil level is above FULL mark, drain to proper level.

5.Insert dipstick. Tighten cap.

Check Engine Oil Level

1.Clean area around dipstick cap (A).

2.Remove dipstick cap (A) from tube. Wipe dipstick clean.

NOTE: Do not tighten dipstick cap when checking oil level.

3.Insert dipstick in tube. Do not tighten cap.

4.Remove dipstick. Check oil level on dipstick. Oil level should be between the ADD and FULL marks.

SPECIFICATIONS - 41

Image 43
Contents Great Dane GSRKA1934S Page Special Messages IntroductionSafety Labels Safety LabelsSafety Labels Safety-Alert SymbolSafety Labels Safety SafetyOperating Safely Using a Spark ArrestorChecking Mowing Area Parking Safely Avoid TippingChecking Wheel Hardware Maintenance and StorageKeep Riders Off Avoid High Pressure FluidsHandling Waste Product and Chemicals Tire SafetyPrevent Fires Handling Fuel SafelyOperator Station Controls OperatingOperating Avoid Damage to Plastic and Painted SurfacesMounting and Dismounting Machine Safely Adjusting Cutting HeightRaising and Lowering Thigh Pad Caster to deck mounting Upper Positon Setting Cutting HeightCaster to deck mounting Lower Positon Testing Safety Systems Testing PTO SwitchTesting Park Brake Switch Testing Neutral Switch StartLocking Park Brake Testing the Park Brake Using the PTOUsing Park Brake Using the ThrottleNeutral Position Using the HourmeterUsing the Motion Control Levers Forward and Reverse MotionSharp Left Turn ForwardGentle Right Turn ReverseEngaging Mower Starting EngineMowing Tips Using Pump Free-Wheel ValvesStopping the Engine Transporting Machine on a TrailerServicing Engine Service IntervalsService Intervals Mowing Travel SpeedsLubricating Mower Deck Idler Pivot Service EngineService Lubrication Lubricating Mower Deck SpindlesChanging Engine Oil and Filter Service EngineEngine Oil Checking Engine Oil LevelChecking and Cleaning Air Filter Elements Cleaning Engine Air Intake Screen and FanReplacing Fuel Filter Service TransmissionHydraulic Oil Service TransmissionChecking Hydraulic Oil Level Changing Hydraulic Oil and FilterRemoving Traction Drive Belt Cleaning Hydraulic Oil Pump Cooling FinsChecking and Adjusting Motion Control Linkages Installing Traction Drive BeltChecking Motion Control Linkages Checking and Adjusting Transmission Tracking Adjusting Motion Control Return to Neutral RTN LinkagesAdjusting Forward and Reverse Speeds Service Steering and BrakesAdjust Neutral Switch Adjusting Park Brake Testing Park Brake Service MowerService Steering & Brakes Service MowerRemoving Mower Deck Drive Belt Adjusting Drive Belt TensionInstalling Mower Deck Drive Belt Replacing Mower Deck Drive BeltChecking and Replacing Mower Blades Checking for Bent Mower BladesBalancing Blades Service ElectricalService Electrical Service the Battery Safely Sharpening BladesRemoving and Installing Battery Checking the Battery Sealed BatteriesInstalling Replacing Fuse Service MiscellaneousUsing Booster Battery Cleaning Battery and TerminalsFilling Fuel Tank Adjusting Operator Presence SwitchService Miscellaneous Using Proper FuelRemoving Removing and Installing Rear Drive WheelsRemoving and Installing Front Caster Wheels Tightening Rear Drive Wheel HardwareServicing Caster Wheel Roller Bearings Checking Tire PressureTroubleshooting TroubleshootingCleaning and Repairing Plastic Surfaces Cleaning and Repairing Metal SurfacesElectrical System StoragePark Brake MachineMower Deck Preparing Fuel and Engine For Storage AssemblyStorage Preparing Machine for StorageRemoving Machine From Storage SpecificationsAssembly Connect Handles Check Hydraulic Oil LevelGetting Quality Service Part Number Great Dane Quality Continues with Quality ServiceWiring Diagram Wiring DiagramHydraulic Schematic Hydraulic SchematicPage Main Frame Assembly QTY Description Hydraulic and Handle Assembly QTY Description ENGINE, Hydraulic and Mainframe Assembly HOSE, 3/8 SAE30R7 Fuel & OIL Console Components Foot PLATE/CONSOLE ComponentsPLATE, Platform TAB LH Deck Assembly PULLEY, Flat 5.0X.38 W/BRG Wheel and Strut ASSEMBLY/PUMP Components WHEEL, Front 11X4X5 SLV Mist Spindle Assembly Spindle Assembly Decal Locations D18197 M117554