Bush Hog RMB 1445 manual Transporting Safety Instructions and Practices, Parts Information

Page 22
(SBM-3)
(SPBH-1)
(SGM-13)
(SGM-10)

SAFETY

SAFETY

Replace bent or broken blades with new blades. NEVER ATTEMPT TO STRAIGHTEN, WELD, OR WELD HARDFACING ON BLADES SINCE THIS WILL LIKELY CRACK OR OTHERWISE DAMAGE THE BLADE WITH SUBSEQUENT FAILURE AND POSSIBLY CAUSE SERIOUS INJURY FROM THROWN BLADES.

DO NOT weld or repair rotating mower components. Welds and other repairs may cause severe vibration and/or component failure resulting in part being thrown from the mower causing serious bodily injury. See your Authorized Dealer for proper repairs.

PARTS INFORMATION

Bush Hog mowers use balanced and matched system components for blade carriers, blades, cuttershafts, knives, knife hangers, rollers, drivetrain components, and bearings. These parts are made and tested to Bush Hog specifications. Non-genuine "will fit" parts do not consistently meet these specifications. The use of “will fit” parts may reduce mower performance, void warranties, and present a safety hazard. Use genuine Bush Hog mower parts for economy and safety.

SEE YOUR BUSH HOG DEALER

Transporting Safety Instructions and Practices

Be particularly careful when transporting the Implement with the Tractor. Turn curves or go up hills only at a low speed and using a gradual steering angle. Rear mounted implements move the center of gravity to the rear and remove weight from the front wheels. Make certain, by adding front ballast, that at least 20% of the tractor’s weight is on the front wheels to prevent rearing up, loss of steering control or Tractor tip-over. Slow down on rough or uneven surfaces to prevent loss of steering control which could result in property damage or possible injury. Do not transport unless 3-Point lift lever is fully raised and in the latched transport position. Dropping implement in transport can cause serious damage to the tractor and/or Implement and possibly cause the operator or others to be injured or killed.

(S3PT-02)

Allow sufficient clearance for the Implement to swing outward while turning. Implements carried behind the Tractor will swing outside the tire path when making turns. Contacting a solid object while turning will cause equipment damage and possible injury. (S3PT-20)

Be particularly careful in transport. The Mower has raised the center of gravity for the tractor and has increased the possibility of overturn. Turn curves or go up slopes only at low speed and using a gradual

turning angle. Slow down on rough or uneven surfaces.

RMB 1445 11/10

Safety Section 1-14

© 2010 Alamo Group Inc.

Image 22
Contents RMB Warranty Information To the Owner/Operator/DealerPage Alamo Group Ag. Division is willing to provide Table of Contents Maintenance Section Hydraulic Hoses Page Safety Section Safety Operator Safety Instructions and Practices SG-36 Wait a minute...Save a life Equipment Operation Safety Instructions and Practices Safety Stop Mowing if Passersby are Within 300 Feet Unless Safety SGM-06 SGM-08 Maintenance and Service Safety Instructions and Practices Safety Transporting Safety Instructions and Practices Parts InformationSafety Concluding Safety Instructions and Practices Decal Location Logo NFS Serial PlateName BookletInstruct NFS SER PLTMULTI-DECAL Decal Description Safety Safety Safety Safety Safety Safety Safety Federal Laws and Regulations Page Introduction Section Introduction Introduction Before Operating this Machine Assembly Section Tractor Selection Installing the Operator Guard Cab Tractor Tractor PreparationBallast Factors that affect stabilityDealer Setup Instructions Stabilizer AttachmentTOP Link Attachment Driveline Attachment Remove Transport Strap Hose RoutingTank Final Assembly ChecksOIL Requirements ISO VG SAEFitting Control Unit in CAB GearboxRemoval from Tractor Running UP ProcedureRMB 1445/1660/1865 With Flail Head only Page Operation Section Operation Operation Operator Requirements Personal Protective Equipment PPERops and Seat Belt Tractor RequirementsOperator Thrown Object Protection Tractor Lighting and SMV Emblem Tractor BallastFront End Weight Tractor Safety DevicesTractor Horsepower 3-Point HitchPower Take Off PTO Getting on and OFF the TractorBoarding the Tractor Dismounting the TractorStarting the Tractor PRE-OPERATION Inspection and Service Tractor Pre-Operation Inspection/Service Boom Unit Pre-Operation Inspection and Service Boom ARM Assembly Frame AssemblyHydraulic Line Inspection Hydraulic PUMP/OIL Reservoir Flail Head Inspection Sickle BAR Inspection Do not Operate an Unsafe Tractor or Implement Do not Operate an Unsafe Tractor or Mower Machine Controls Rotor Controls Reversing Rotation With FlailheadEngaging Drive Angle FloatRotor Operating Speed Operating Speed Forward SpeedTractor Position Parallel Motion GeometryBreakaway Action High Voltage CablesCutting Sequence Grass Cutting Driving the Tractor and Implement Starting the Tractor Brake and Differential Lock Setting Operating the Tractor and Implement Driving the Tractor and BoomOperating Instructions RMB 1445 11/10 Operation Section Bystanders/Passersby Precautions Foreign Debris HazardsEngaging the Power Take Off PTO Operating Speed and Ground Speed Operating the MowerSGM-08 Grass Flail Operating the Attached Mower HeadsSickle Bar TRACTOR, BOOM, and Attached Head Storage Shutting Down the Attached HeadTransporting the Tractor and Implement Transporting on Public Roadways Operation Hauling the Tractor and Implement Operation Troubleshooting Guide Trouble Possible Cause Possible RemedyOperation Operation Maintenance Section Maintenance LubricationPTO Shaft PTO LubricationCutting PTO Shaft Maintenance Hydraulic System Filtration MaintenanceHose Replacement Hydraulic HosesHose Warranty PTO GearboxFlailhead CablesProper Torque Values for Fasteners Hose ConnectionsMain Control Valve Maintenance Page Limited Warranty Required of the Owner Required of the OperatorRMB 1445 Rear Mount Boom Mower