Exmark 4500-501 Rev A manual Specifications, Model Numbers, Systems

Page 16

Specifications

Specifications

Model Numbers

Serial Nos: 790,000 and Higher

LXS25KD605; LXS25KD665; LXS25KD725

Systems

Engine

Engine Specifications: See your Engine Owner’s Manual

RPM: Full Speed: 3850 ±50 RPM (No Load)

Idle: 1400 RPM

Fuel System

Capacity: 15.5 gal. (58.6 L)

Type of Fuel: Diesel fuel, 40 cetane or higher or biodiesel up to B20 (20% biodiesel, 80% petro diesel).

Fuel Filter: In-line 113 Micron Exmark P/N 112-7836.

Fuel Shut-Off Valve: 1/4 turn increments (“OFF”, right tank, left tank, )

Fuel gauge in left hand fuel tank.

Electrical System

Charging System: External Alternator

Charging Capacity: 60 amps

Battery Type: BCI Group 26

Battery Voltage: 12 Volt

Polarity: Negative Ground

Fuses: One 20 amp blade type; One 30 amp blade type

Safety Interlock System

PTO must be disengaged, brake engaged, and motion control levers out (neutral lock) to start engine. (It is not necessary for the operator to be in the seat to start the engine.)

Operator must be in seat when PTO is engaged, brake is disengaged, or motion control levers are moved in or engine will stop.

Engine will stop if either the left, the right, or both levers are moved from neutral lock position while brake is engaged.

Cooling System

Fan: Electric with continuous operation with engine running.

Coolant Liquid: 50/50 mix of DexCool© extended life antifreeze and water.

Coolant Capacity: 4 quarts

Operator Controls

Steering and Motion Control:

Note: Motion control levers are adjustable to two heights.

Separate levers, on each side of the console, control speed and direction of travel of the respective drive wheels.

Steering is controlled by varying the position of the levers relative to each other.

Moving motion control levers outward (in slots) locks the drive system in neutral.

PTO Engagement Switch: Engages electric clutch (to drive belt) which engages mower blades.

Parking Brake Lever: Engages parking brake.

Deck Height Adjustment Lever: Sets cutting height to desired position.

Deck Lift Assist Lever: Foot pedal that assists in raising the deck.

Seat

Type: Deluxe suspension seat high back, low profile foam-in-place cushion (dampened, adjustable spring suspension) and armrests, adjustable back angle.

16

Image 16 Contents
Lazer Z XS California Introduction Contents Safety Safety Alert SymbolSafe Operating Practices TrainingOperation Slope Operation Using the Rollover Protection System Rops Maintenance and StorageSafety Safety and Instructional Decals 103-0223 103-0261 103-1798 103-2076 103-7218 107-2102 Safety 109-2264 109-2478 109-2951 109-3148 Safety 107-9866 Model Numbers SpecificationsSystems Tires & Wheels Hydrostatic Ground Drive SystemCutting Deck Dimensions Torque RequirementsOperation Product OverviewControls Tracking Adjustment Knob PTO Engagement SwitchCoolant Temperature Gauge Hour MeterPre-Start Operating Instructions Raise the Rollover Protection System RopsOpen the Fuel Shut-Off Valve Starting the EngineEngaging the PTO Disengaging the PTOStopping the Engine Driving the MachineAdjusting the Cutting Height Driving ForwardAdjusting the Anti-Scalp Rollers Transporting a Unit TransportingLoading a Unit Operation Maintenance Recommended Maintenance SchedulesCheck Battery Charge Check Engine Oil LevelCheck Safety Interlock System Check Mower BladesCheck Rollover Protections Systems Roll Bar Pins Service Air CleanerCheck Seat Belt Check for Loose HardwareChange Engine Oil Check Hydraulic Oil LevelCheck Tire Pressures Check Condition Of BeltsLubricate Grease Fittings Lubricate Caster Wheel HubsLubricate Brake Handle Pivot Lubricate Brake Rod BushingsLubricate Motion Control Bronze Bushings Drain Fuel Filter/Water SeparatorWheel Hub Slotted Nut Torque Specification Change Fuel Filter/Water SeparatorChange Inline Fuel Filter Change Hydraulic System FilterCheck Engine Coolant Level Change Engine CoolantThread Locking Adhesives Fuel Tank Mounting Hardware SpecificationsMobil HTS Grease Or Food-Grade Anti-seize Dielectric Grease Copper-Based Anti-seizeDeck Leveling Mule Drive Belt Tension Adjustment Pump Drive Belt TensionBelt Guide Adjustment Brake Link AdjustmentDeck Belt Tension Alternator Belt TensionElectric Clutch Adjustment Brake AdjustmentReverse Indicator Adjustment Motion Control Linkage Adjustment Motion Control Damper Adjustment Caster Pivot Bearings Pre-Load AdjustmentClutch Shim Removing the Shim Feeler gauge Clean Engine Cooling System Cleaning of the RadiatorClean Debris From Machine Remove Accumulated Debris from EngineClean Grass Build-Up Under Deck Battery DisposalWaste Disposal Motor Oil DisposalTroubleshooting Problem Possible Cause Corrective ActionTroubleshooting Troubleshooting Ignition Switch ElectricalElectrical Logic Schematic Hydraulic Diagram Exmark Commercial Turf Equipment Page Page Service Record Page Page See EXMARK’S Complete Line of Accessories and Options
Related manuals
Manual 60 pages 60.11 Kb