Exmark 4500-501 Rev A manual See EXMARK’S Complete Line of Accessories and Options

Page 60

SEE EXMARK’S COMPLETE LINE OF ACCESSORIES AND OPTIONS

MID-MOUNT RIDING ACCESSORIES AND OPTIONS

CUSTOM RIDE SEAT SUSPENSION SYSTEM	OPERATOR CONTROLLED DISCHARGE
FULL SUSPENSION SEAT	ROLL OVER PROTECTION SYSTEM (ROPS)
DECK LIFT ASSIST KIT	SUN SHADE
HITCH KIT	TRASH CONTAINER
LIGHT KIT	TURF STRIPER
12V POWER PORT	ULTRA VAC COLLECTION SYSTEM
MICRO-MULCH SYSTEM	ULTRA VAC QUICK DISPOSAL SYSTEM
OUT-FRONT RIDING ACCESSORIES AND OPTIONS
CUSTOM RIDE SEAT SUSPENSION SYSTEM	SNOW BLADE
DUAL-TAIL WHEEL	SNOWBLOWER
FLOOR PAN EXTENDER	SUN SHADE
HITCH KIT	TRASH CONTAINER
LIGHT KIT	ULTRA VAC COLLECTION SYSTEM
MICRO-MULCH SYSTEM	ULTRA VAC QUICK DISPOSAL SYSTEM
ROLL OVER PROTECTION SYSTEM (ROPS)	WEATHER CAB

WALK-BEHIND ACCESSORIES AND OPTIONS

GRASS CATCHER

MICRO-MULCH SYSTEM

Place Model No. and Serial No.

Label Here (Included in the Literature

Pack) or Fill in Below

Model No.

Serial No.

TURF STRIPER

STANDON

Date Purchased

Engine Model No. and Spec. No.

Engine Serial No. (E/No)

© 2009 Exmark Mfg. Co., Inc.	Part No. 4500-501 Rev. A
Industrial Park Box 808	(402) 223-6300
Beatrice, NE 68310	Fax (402) 223-5489
All Rights Reserved	Printed in the USA

www.exmark.com

Image 60

Contents

Lazer Z XS California Introduction Contents Safety Safety Alert SymbolSafe Operating Practices TrainingOperation Slope Operation Using the Rollover Protection System Rops Maintenance and StorageSafety Safety and Instructional Decals 103-0223 103-0261 103-1798 103-2076 103-7218 107-2102 Safety 109-2264 109-2478 109-2951 109-3148 Safety 107-9866 Specifications Model NumbersSystems Hydrostatic Ground Drive System Tires & WheelsCutting Deck Dimensions Torque RequirementsProduct Overview OperationControls Tracking Adjustment Knob PTO Engagement SwitchCoolant Temperature Gauge Hour MeterPre-Start Operating Instructions Raise the Rollover Protection System RopsOpen the Fuel Shut-Off Valve Starting the EngineEngaging the PTO Disengaging the PTOStopping the Engine Driving the MachineAdjusting the Cutting Height Driving ForwardAdjusting the Anti-Scalp Rollers Transporting Transporting a UnitLoading a Unit Operation Maintenance Recommended Maintenance SchedulesCheck Battery Charge Check Engine Oil LevelCheck Safety Interlock System Check Mower BladesCheck Rollover Protections Systems Roll Bar Pins Service Air CleanerCheck Seat Belt Check for Loose HardwareChange Engine Oil Check Hydraulic Oil LevelCheck Tire Pressures Check Condition Of BeltsLubricate Grease Fittings Lubricate Caster Wheel HubsLubricate Brake Handle Pivot Lubricate Brake Rod BushingsLubricate Motion Control Bronze Bushings Drain Fuel Filter/Water SeparatorWheel Hub Slotted Nut Torque Specification Change Fuel Filter/Water SeparatorChange Inline Fuel Filter Change Hydraulic System FilterCheck Engine Coolant Level Change Engine CoolantFuel Tank Mounting Hardware Specifications Thread Locking AdhesivesMobil HTS Grease Or Food-Grade Anti-seize Copper-Based Anti-seize Dielectric GreaseDeck Leveling Mule Drive Belt Tension Adjustment Pump Drive Belt TensionBelt Guide Adjustment Brake Link AdjustmentDeck Belt Tension Alternator Belt TensionBrake Adjustment Electric Clutch AdjustmentReverse Indicator Adjustment Motion Control Linkage Adjustment Caster Pivot Bearings Pre-Load Adjustment Motion Control Damper AdjustmentClutch Shim Removing the Shim Feeler gauge Clean Engine Cooling System Cleaning of the RadiatorClean Debris From Machine Remove Accumulated Debris from EngineClean Grass Build-Up Under Deck Battery DisposalWaste Disposal Motor Oil DisposalTroubleshooting Problem Possible Cause Corrective ActionTroubleshooting Troubleshooting Ignition Switch ElectricalElectrical Logic Schematic Hydraulic Diagram Exmark Commercial Turf Equipment Page Page Service Record Page Page See EXMARK’S Complete Line of Accessories and Options

Related manuals

Manual 60 pages 60.11 Kb