Exmark 4500-996 Rev A manual Throttle Control, Brake Lever, Hour Meter, Ignition Switch, Operation

Page 19

Throttle Control

Operation

rear, to the detent, will put the choke in the “OFF” position. Do Not run a warm engine with choke in the “ON” position.

The ignition switch is used to start and stop the engine. The switch has three positions “OFF”, “ON” and “START”. Insert key into switch and rotate clockwise to the “ON” position. Rotate clockwise to the next position to engage the starter (key must be held against spring pressure in this position). Allow the key to return to the “on” position immediately after the engine starts.

Figure 6

1.	Throttle lever	4.	Blade control switch
			(power take-off)
2.	Choke lever	5.	Ignition switch

3.Hour meter

		Figure 7
1.	Off	3. Start
2.	On

Note: Brake must be engaged, motion control levers out (neutral lock position) and PTO switch disengaged to start engine. (It is not necessary for the operator to be in the seat to start the engine.)

Throttle Control

Located on right console (red lever) (see Figure 6).

The throttle is used to control engine speed. Moving the throttle lever forward will increase engine speed and moving the throttle lever to the rear will decrease engine speed. Moving the throttle forward into the detent is full throttle.

Brake Lever

Located on left side of unit, just to the front of the LH motion control lever.

The brake lever engages a parking brake on the drive wheels.

Pull the lever up and rearward to engage the brake.

Push the lever forward and down to disengage the brake.

The unit must be tied down and brake engaged when transporting.

Hour Meter

Located on the control panel (see Figure 6 and Figure 8).

The hour meter records the number of hours that the engine has run.

Figure 8

1. LCD indicators

3. Hour/Voltage display

2.Low voltage indicator light

Ignition Switch	Fuel Shut-Off Valve
Located on right console (see Figure 6).	Located by the lower LH ROPS tube mounting.

19

Image 19

Contents For Serial Nos 312,000,000 & Higher PIONEER E-SERIESAll Rights Reserved CALIFORNIA Proposition 65 WarningModel No Serial No IntroductionContents ALERT! YOUR SAFETY IS INVOLVED SafetySafety Alert Symbol SafetyKeep away from eyes and skin Never siphon by mouth DANGERAvoid prolonged breathing of vapors Keep face away from nozzle and gas tank/container openingRemove accumulated debris from muffler and engine area OperationSlope Operation Allow engine parts, especially the muffler, to cool before touchingLower the roll bar only when absolutely necessary Using the Rollover Protection System ROPSMaintenance and Storage Do Not mow slopes when grass is wetVentilate when charging or using battery in an enclosed space Keep sparks, flames, or cigarettes away from batteryDo Not swallow electrolyte Use cardboard or paper, not your hands, to find hydraulic leaks Safety and Instructional Decals 109-6014 107-2102116-4465 PTO Switch Symbols116-6363 116-4308116-4430 109-6016Reverse Model Numbers SpecificationsSpecifications Safety Interlock SystemCutting Deck Tires & WheelsSeat Hydrostatic Ground Drive SystemOverall Width DimensionsCurb Weight Torque RequirementsMotion Control Levers Product OverviewControls OperationHour Meter Ignition SwitchThrottle Control Brake LeverDrive Wheel Release Valves PTO Engagement SwitchDo Not tow machine Transport Lock Pre-StartOperating Instructions Deck Lift PedalStarting the Engine Open the Fuel Shut-Off ValveEngaging the PTO Driving the Machine Use caution when making turnsDisengaging the PTO Stopping the EngineDriving in Reverse Adjusting the Cutting HeightDo Not drive a unit on a public street or roadway Adjusting the Anti-Scalp RollersTransporting Transporting a UnitLoading a Unit Use extreme caution when operating a unit on a rampRecommended Maintenance Schedules MaintenanceMaintenance Service Interval Before each use or daily Periodic MaintenanceCheck Battery Charge Recommended Jump Starting ProcedureShield the eyes and face from the batteries at all times Do Not jump start a weak battery if these conditions existCheck Mower Blades Batteries contain acid and produce explosive gases1. Spindle 2. Blade 3. Blade drive washer Check Safety Interlock SystemSERVICE DEALER 4. Blade bolt washer assembly - Torque to 50-60 ft-lbCheck Seat Belt Service Air CleanerService Interval After the first 5 hours Check Rollover Protections Systems Roll Bar KnobsCheck Tire Pressures Service Interval Every 50 hoursNote See chart for service intervals Service Interval Every 200 hoursChange Hydraulic System Filter and Fluid Service Interval Every 500 hoursService Interval After the first 100 hours Replace Emissions Air Intake FilterCopper-Based Anti-seize Do Not refuel or run engine unless spark arrester is installedCheck Spark Arrester if equipped Thread Locking AdhesivesBlade Slope AdjustmentsAdjusting the Blade Slope Deck LevelingPump Drive Belt Tension Adjusting the Parking BrakeDeck Belt Tension Adjusting the height Motion Control Handle AdjustmentAdjusting the Tilt Motion Control Linkage Adjustment Full Forward Tracking Adjustment8. Tighten nuts Adjusting the Seat Ride SuspensionElectric Clutch Adjustment No adjustment necessaryClean Hydro Fan Cooling Fins CleaningClean Engine and Exhaust System Area Remove Engine Shrouds and Clean Cooling Finsrecycling center or according to your state and local regulations Battery DisposalTroubleshooting TroubleshootingCutting blades is/are bent or unbalanced see Drive Wheel Release Valves sectionSchematics SchematicsElectrical Diagram Electrical Logic Schematic General Warranty Conditions and Products Covered Pioneer E-Series Turf Equipment1 Year Limited Commercial Warranty 4 Year or 500 Hours Limited Consumer WarrantyPage Page Description of Work Done Service RecordService Done By DatePage This page may be copied for personal use WALK-BEHIND ACCESSORIES AND OPTIONS SEE EXMARK’S COMPLETE LINE OF ACCESSORIES AND OPTIONSMID-MOUNT RIDING ACCESSORIES AND OPTIONS OUT-FRONT RIDING ACCESSORIES AND OPTIONS