Exmark TTS18KA523, TTS16KA363CA, TTS16KA483CA manual Specifications, Model Numbers, Systems

Page 14

Specifications

Specifications

Model Numbers

Serial Nos: 920,000 and Higher

Manual Start Models: TTS16KA363; TTS16KA363CA; TTS16KA483; TTS16KA483CA; TTS18KA523

Electric Start Models: TTS20KAE483; TTS20KAE483CA; TTS20KAE523

Systems

Engine

•Engine Specifications: See your Engine Owner’s Manual

•Engine Oil Type: Exmark 4–Cycle Premium Engine Oil

•RPM: Full Speed: 3600 (No Load)

Idle: 1550 RPM

Fuel System

•Capacity: 5.0 gal. (18.9 L)

•Type of Fuel: Regular unleaded gasoline, 87 octane or higher; containing no more than 10% methanol or ethanol.

•Fuel Filter: Replaceable In-line

•Fuel Shut-Off Valve: 1/4 turn increments

Electrical System (Electric Start)

•Charging System: Flywheel Alternator

•Charging Capacity: 15 amps

•Battery Type: BCI Group U1

•Battery Voltage: 12 Volt

•Polarity: Negative Ground

•Fuses: Two 20 amp blade type

Operator Controls

Steering Control: Fingertip drive control levers provide independent speed control, braking and neutral to each drive wheel for moving forward or reverse, stopping, and power turning.

Transmission

Twin Hydrostatic Drive

•Two Hydro Gear variable displacement high efficiency pumps independently coupled to two high efficiency Parker/Ross wheel drive motors.

•Hydraulic Oil: Use Exmark Premium Hydro Oil.

•Hydraulic Oil Capacity: 2.4 qt. (2.2 L)

•Hydraulic Filter is replaceable cartridge type.

P/N 109-4180: 25 microns, 10 psi bypass (Summer use above 32°F (0°C))

P/N 1-523541: 40 microns, 18 psi bypass (Winter use below 32°F (0°C))

•Speeds:

–0-6.2 mph (10.0 km/hr) forward.

–0-2.2 mph (3.5 km/hr) reverse.

•Drive wheels release valves allow machine to be moved when engine is not running.

Safety Interlock System:

•Operator must have OPC (Operator Presence Control) levers held in contact with handle grips, speed control lever in neutral, and PTO disengaged to start engine. Release of OPC levers will cause the engine to stop if speed control lever is not in neutral and/or PTO is engaged.

•Park brake must be disengaged to move speed control out of neutral or engine will kill.

Wheel Drive System

Drive wheels are direct coupled to Parker wheel drive motors with 1 inch (25.4 mm) tapered shaft.

14

Page 13 Page 15
Image 14
Page 13 Page 15
Contents Turf Tracer Series California Introduction Contents Safe Operating Practices SafetySafety Alert Symbol TrainingSafety Operation Slope OperationMaintenance and Storage Safety Safety and Instructional Decals 413327 103-1977 109-3148 116-0404 117-2718 Systems SpecificationsModel Numbers Dimensions Product Overview Torque RequirementsOperation ControlsTracking Adjustment Knob Off-Run Switch Manual Start OnlyIgnition Switch Electric Start Only Park Brake LeverOpen the Fuel Shut-Off Valve Pre-StartOperating Instructions Starting the Engine Manual StartDriving the Machine Disengaging the PTOStopping the Engine Drive Lever/Neutral Lock Latch OperationDriving in Reverse Adjusting the Cutting HeightDriving Forward Adjusting the Anti-Scalp Rollers Transporting Transporting a UnitMaintenance Recommended Maintenance SchedulesProposition 65 Warning Check Battery Charge Electric Start Units OnlyCheck Engine Oil Level Service Interval As required Do Not jump start a weak battery if these conditions existReplacing the Discharge Deflector Install bushing/blade assembly into spindleCheck Mower Blades Check for Loose Hardware Check Safety Interlock SystemService Air Cleaner Check Condition Of Belts Change Engine OilCheck Tire Pressures Check Hydraulic Oil LevelChange Hydraulic System Filter Check Spark PlugsChange Fuel Filter LevelHydraulic System Air Purge Style a black finish Wheel Hub-Slotted Nut Torque SpecificationReplace Emissions Air Intake Filter Torque the slotted nut to 140-155 ft-lb 190-210 N-mMobil HTS Grease Or Food-Grade Anti-seize Inspect PTO Clutching Belt TensionThread Locking Adhesives Copper-Based Anti-seizeDeck Leveling Park Brake AdjustmentHydro Drive Linkage Adjustment Pump Drive Belt TensionAdjust Hydro Control Linkages Repeat above adjustments if necessaryDrive Lever Linkage Adjustment Tracking AdjustmentHydro Pump Spring Tension Setting Remove Engine Shrouds and Clean Cooling Fins PTO Safety SwitchClean Engine and Exhaust System Area Retighten PTO switch mounting hardwareBattery Disposal Clean Debris From MachineClean Grass Build-Up Under Deck Waste DisposalTroubleshooting Problem Possible Cause Corrective ActionTroubleshooting Schematics Electrical DiagramSchematics Hydraulic Diagram Exmark Commercial Turf Equipment Service Record Date Description of Work Done Service Done ByPage This page may be copied for personal use See EXMARK’S Complete Line of Accessories and Options
Top Page Image Contents