Exmark TTS16KA363CA manual Check Engine Oil Level, Check Battery Charge Electric Start Units Only

Page 25

Maintenance

Maintenance Service

Maintenance Procedure

Interval

 

 

 

 

• Change the hydraulic filter (Every 250 hours/yearly if using Mobil 1 15W50)

Every 500 hours

• Replace the emissions air intake filter.

 

• Check wheel hub-slotted torque specification.

Monthly

• Check the battery charge.

• Grease the PTO engagement bellcrank.

 

 

 

Periodic Maintenance

Check Engine Oil Level

Service Interval: Before each use or daily

1.Stop engine and wait for all moving parts to stop. Make sure unit is on a level surface.

2.Check with engine cold.

3.Clean area around dipstick. Remove dipstick and wipe oil off. Reinsert the dipstick and push it all the way down into the tube. Do Not screw into place. Remove the dipstick and read the oil level.

4.If the oil level is low, wipe off the area around the oil fill cap, remove cap and fill to the “FULL” mark on the dipstick. Exmark 4-Cycle Premium Engine Oil is recommended; refer to the Engine Owner’s manual for an acceptable alternative. Do Not overfill.

Important: Do Not operate the engine with the oil level below the “LOW” (or “ADD”) mark on the dipstick, or over the “FULL” mark.

Check Battery Charge (Electric Start Units Only)

Service Interval: Monthly

WARNING

CALIFORNIA

Proposition 65 Warning

Battery posts, terminals, and related accessories contain lead and lead compounds, chemicals known to the State of California to cause cancer and reproductive harm. Wash hands after handling.

Allowing batteries to stand for an extended period of time without recharging them will result in reduced

performance and service life. To preserve optimum battery performance and life, recharge batteries in storage when the open circuit voltage drops to 12.4 volts.

Note: To prevent damage due to freezing, battery should be fully charged before putting away for winter storage.

Check the voltage of the battery with a digital voltmeter. Locate the voltage reading of the battery in the table and charge the battery for the recommended time interval to bring the charge up to a full charge of 12.6 volts or greater.

Important: Make sure the negative battery cables are disconnected and the battery charger used for charging the battery has an output of 16 volts and 7 amps or less to avoid damaging the battery (see chart for recommended charger settings).

Voltage

Percent

Maximum

Charging

Reading

Charge

Charger

Interval

 

 

Settings

 

12.6 or

100%

16 volts/7

No

greater

 

amps

Charging

 

 

 

Required

12.4 – 12.6

75–100%

16 volts/7

30 Minutes

 

 

amps

 

12.2 – 12.4

50–75%

16 volts/7

1 Hour

 

 

amps

 

12.0–12.2

25–50%

14.4 volts/4

2 Hours

 

 

amps

 

11.7–12.0

0–25%

14.4 volts/4

3 Hours

 

 

amps

 

11.7 or less

0%

14.4 volts/2

6 Hours or

 

 

amps

More

25

Image 25
Contents Turf Tracer Series California Introduction Contents Safety Alert Symbol SafetySafe Operating Practices TrainingSafety Slope Operation OperationMaintenance and Storage Safety Safety and Instructional Decals 413327 103-1977 109-3148 116-0404 117-2718 Model Numbers SpecificationsSystems Dimensions Torque Requirements Product OverviewControls OperationIgnition Switch Electric Start Only Off-Run Switch Manual Start OnlyTracking Adjustment Knob Park Brake LeverOperating Instructions Pre-StartOpen the Fuel Shut-Off Valve Starting the Engine Manual StartStopping the Engine Disengaging the PTODriving the Machine Drive Lever/Neutral Lock Latch OperationDriving Forward Adjusting the Cutting HeightDriving in Reverse Adjusting the Anti-Scalp Rollers Transporting a Unit TransportingRecommended Maintenance Schedules MaintenanceCheck Engine Oil Level Check Battery Charge Electric Start Units OnlyProposition 65 Warning Do Not jump start a weak battery if these conditions exist Service Interval As requiredCheck Mower Blades Install bushing/blade assembly into spindleReplacing the Discharge Deflector Service Air Cleaner Check Safety Interlock SystemCheck for Loose Hardware Check Tire Pressures Change Engine OilCheck Condition Of Belts Check Hydraulic Oil LevelChange Fuel Filter Check Spark PlugsChange Hydraulic System Filter LevelHydraulic System Air Purge Replace Emissions Air Intake Filter Wheel Hub-Slotted Nut Torque SpecificationStyle a black finish Torque the slotted nut to 140-155 ft-lb 190-210 N-mThread Locking Adhesives Inspect PTO Clutching Belt TensionMobil HTS Grease Or Food-Grade Anti-seize Copper-Based Anti-seizeHydro Drive Linkage Adjustment Park Brake AdjustmentDeck Leveling Pump Drive Belt TensionRepeat above adjustments if necessary Adjust Hydro Control LinkagesHydro Pump Spring Tension Setting Tracking AdjustmentDrive Lever Linkage Adjustment Clean Engine and Exhaust System Area PTO Safety SwitchRemove Engine Shrouds and Clean Cooling Fins Retighten PTO switch mounting hardwareClean Grass Build-Up Under Deck Clean Debris From MachineBattery Disposal Waste DisposalProblem Possible Cause Corrective Action TroubleshootingTroubleshooting Electrical Diagram SchematicsSchematics Hydraulic Diagram Exmark Commercial Turf Equipment Date Description of Work Done Service Done By Service RecordPage This page may be copied for personal use See EXMARK’S Complete Line of Accessories and Options