Exmark TTS20KAE483CA, TTS16KA363CA, TTS16KA483CA, TTS20KAE523, TTS18KA523 Transporting a Unit

Page 23

Operation

Figure 9

1.

Spring disc washer

3.

3/8 nyloc-torque to 30-35

 

(cone towards nut )

 

ft-lb (41-47 N-m)

2.

Front right anti-scalp

4.

3/8-16 whizlock nut

 

bracket shown

 

torque to 30-35 ft-lb

 

 

 

(41-47 N-m)

 

 

 

 

Transporting

Transporting a Unit

WARNING

Loading the mower onto a trailer without strong enough or properly supported ramps could be dangerous. The ramps could collapse causing the unit to fall, which could cause injury.

Use proper ramps that are secured to the truck or trailer.

Keep feet and legs out from under the unit when loading and unloading.

If necessary, use assistance when loading.

Be sure the fuel shut-off valve is closed.

Use a heavy duty trailer to transport the machine. Engage neutral lock latches and park brake, then block wheels.

Securely fasten the machine to the trailer with straps, chains, cables, or ropes.

Do Not rely solely on the parking brake to hold the machine on the trailer.

Be sure that the trailer has all necessary lighting and marking as required by law and use a safety chain.

23

Image 23
Contents Turf Tracer Series California Introduction Contents Training SafetySafety Alert Symbol Safe Operating PracticesSafety Slope Operation OperationMaintenance and Storage Safety Safety and Instructional Decals 413327 103-1977 109-3148 116-0404 117-2718 Systems SpecificationsModel Numbers Dimensions Torque Requirements Product OverviewControls OperationPark Brake Lever Off-Run Switch Manual Start OnlyIgnition Switch Electric Start Only Tracking Adjustment KnobStarting the Engine Manual Start Pre-StartOperating Instructions Open the Fuel Shut-Off ValveDrive Lever/Neutral Lock Latch Operation Disengaging the PTOStopping the Engine Driving the MachineDriving in Reverse Adjusting the Cutting HeightDriving Forward Adjusting the Anti-Scalp Rollers Transporting a Unit TransportingRecommended Maintenance Schedules MaintenanceProposition 65 Warning Check Battery Charge Electric Start Units OnlyCheck Engine Oil Level Do Not jump start a weak battery if these conditions exist Service Interval As requiredReplacing the Discharge Deflector Install bushing/blade assembly into spindleCheck Mower Blades Check for Loose Hardware Check Safety Interlock SystemService Air Cleaner Check Hydraulic Oil Level Change Engine OilCheck Tire Pressures Check Condition Of BeltsLevel Check Spark PlugsChange Fuel Filter Change Hydraulic System FilterHydraulic System Air Purge Torque the slotted nut to 140-155 ft-lb 190-210 N-m Wheel Hub-Slotted Nut Torque SpecificationReplace Emissions Air Intake Filter Style a black finishCopper-Based Anti-seize Inspect PTO Clutching Belt TensionThread Locking Adhesives Mobil HTS Grease Or Food-Grade Anti-seizePump Drive Belt Tension Park Brake AdjustmentHydro Drive Linkage Adjustment Deck LevelingRepeat above adjustments if necessary Adjust Hydro Control LinkagesDrive Lever Linkage Adjustment Tracking AdjustmentHydro Pump Spring Tension Setting Retighten PTO switch mounting hardware PTO Safety SwitchClean Engine and Exhaust System Area Remove Engine Shrouds and Clean Cooling FinsWaste Disposal Clean Debris From MachineClean Grass Build-Up Under Deck Battery DisposalProblem Possible Cause Corrective Action TroubleshootingTroubleshooting Electrical Diagram SchematicsSchematics Hydraulic Diagram Exmark Commercial Turf Equipment Date Description of Work Done Service Done By Service RecordPage This page may be copied for personal use See EXMARK’S Complete Line of Accessories and Options