Exmark LZDS manual Specifications, Model Numbers, Systems

Page 17

Specifications

Specifications

Model Numbers

Serial Nos: 312,000,000 and Higher

LZDS902K605; LZDS902K725

Systems

Engine

Engine Specifications: See your Engine Owner’s Manual

Engine Oil Type: Exmark 4–Cycle Premium Engine Oil

RPM: Full Speed: 3850 ±50 RPM (PTO not

engaged) Idle: 1400 ±100 RPM

Fuel System

Capacity: 15.5 gal. (58.6 L)

Type of Fuel: Diesel fuel, 40 cetane or higher or biodiesel up to B20 (20% biodiesel, 80% petro diesel).

Fuel Filter: In-line 113 Micron Exmark P/N 112-7836.

Fuel Shut-Off Valve: 1/4 turn increments (“OFF”, right tank, left tank, )

Fuel gauge in left hand fuel tank.

Operator must be in seat when PTO is engaged, brake is disengaged, or motion control levers are moved in or engine will stop.

Engine will stop if either the left, the right, or both levers are moved from neutral lock position while brake is engaged.

Engine Overheat Protection System

PTO will disengage, an alarm will sound, and the coolant temperature gauge will be in the red area when the engine temperature reaches an overheat condition. The PTO will not re-engage until the engine has cooled and the PTO switch is manually shut-off and re-engaged.

Note: If the engine coolant level is below the indicator line on the overflow bottle when the engine is cold, the coolant temperature gauge may not register correctly during operation and/or the warning buzzer may not sound if the engine overheats. Refer to Check Engine Coolant Level in Maintenance.

Electrical System

Charging System: External Alternator

Charging Capacity: 60 amps

Battery Type: BCI Group 26

Recommended Minimum Battery CCA: 540 CCA

Battery Voltage: 12 Volt

Polarity: Negative Ground

Fuses: One 20 amp blade type; One 30 amp blade type

Safety Interlock System

PTO must be disengaged, brake engaged, and motion control levers out (neutral lock) to start engine. (It is not necessary for the operator to be in the seat to start the engine.)

Cooling System

Fan: Electric with continuous operation with engine running.

Coolant Liquid: 50/50 mix of DexCool© extended life antifreeze and water.

Coolant Capacity: 4 quarts

Operator Controls

Steering and Motion Control:

Note: Motion control levers are adjustable to two heights.

Separate levers, on each side of the console, control speed and direction of travel of the respective drive wheels.

Steering is controlled by varying the position of the levers relative to each other.

17

Image 17
Contents Lazer Z DS-SERIES California Introduction Contents Safety Alert Symbol SafetySafe Operating Practices TrainingOperation Slope Operation Maintenance and Storage Using the Rollover Protection System RopsSafety Safety Safety and Instructional Decals 103-0223 103-0261 103-1798 103-2076 103-7218 107-2102 109-0872 109-1214 109-1215 109-1399 109-2219 109-2263 109-2264 109-2478 109-2951 109-3148 117-2718 19426-87881 19426-87903 107-9866 Systems SpecificationsModel Numbers Hydrostatic Ground Drive System SeatTires & Wheels Cutting DeckTorque Requirements DimensionsOperation Product OverviewControls Motion Control LeversTracking Adjustment Knob Ignition SwitchBrake Lever Hour MeterPre-Start Biodiesel Ready Operating InstructionsRaise the Rollover Protection System Rops Open the Fuel Shut-Off ValveStopping the Engine Engaging the PTODisengaging the PTO Driving Forward Driving the MachineAdjusting the Anti-Scalp Rollers Adjusting the Cutting HeightLoading a Unit TransportingTransporting a Unit Operation Recommended Maintenance Schedules MaintenanceCheck Engine Oil Level Check Battery ChargeRecommended Jump Starting Procedure Engine Block of the Stalled Check Mower BladesCheck Rollover Protections Systems Roll Bar Pins Check Safety Interlock SystemService Air Cleaner Check Seat BeltCheck Tire Pressures Change Engine OilCheck Hydraulic Oil Level Lubricate Grease Fittings Check Condition Of BeltsLubricate Caster Wheel Hubs Wheel Hub Slotted Nut Torque SpecificationLubricate Brake Handle Pivot Lubricate Brake Rod BushingsDrain Fuel Filter/Water Separator Lubricate Motion Control Bronze BushingsChange Fuel Filter/Water Separator Change Inline Fuel FilterChange Engine Coolant Check Engine Coolant LevelThread Locking Adhesives Check Spark Arrester if equippedCopper-Based Anti-seize Mobil HTS Grease Or Food-Grade Anti-seizeDielectric Grease Deck LevelingDeck Belt Tension Mule Drive Belt Tension AdjustmentPump Drive Belt Tension Alternator Belt Tension Belt Guide AdjustmentParking Brake Adjustment Lever down Remove pin to adjust Disengaged Removing the Shim Electric Clutch AdjustmentMotion Control Linkage Adjustment Reverse Indicator AdjustmentBecause of the jumper wire being used. Run Caster Pivot Bearings Pre-Load Adjustment Motion Control Damper AdjustmentClean the Radiator Clean Engine Cooling SystemClean Engine and Exhaust System Area Clean Grass Build-Up Under Deck Clean Debris From MachineBattery Disposal Waste DisposalProblem Possible Cause Corrective Action TroubleshootingTroubleshooting Troubleshooting Electrical Diagram SchematicsElectrical Schematic Exmark Commercial Turf Equipment Page Date Description of Work Done Service Done By Service RecordPage This page may be copied for personal use See EXMARK’S Complete Line of Accessories and Options

LZDS specifications

The Exmark LZDS stands as a benchmark in the world of commercial lawn care equipment. Designed specifically for landscape professionals, the LZDS combines power, efficiency, and precision to deliver exceptional results in varied conditions. One of its hallmark features is the robust engine, engineered to handle large-scale mowing tasks without sacrificing reliability. The Exmark LZDS is equipped with a powerful Kohler Command Pro engine, which provides superior torque and smooth operation, making it ideal for tackling tough terrains.

The LZDS showcases Exmark’s signature UltraCut deck technology, which is designed to enhance cutting performance and deliver a clean, even cut. The deck comes in various sizes, allowing users to choose the perfect fit based on their specific mowing requirements. The heavy-duty construction ensures durability, while the unique design minimizes clumping and provides improved airflow, contributing to a flawless finish on every lawn.

One of the standout characteristics of the Exmark LZDS is its zero-turn capability. This feature allows for unparalleled maneuverability, enabling operators to navigate complex landscapes with ease. The intuitive controls and comfortable seating position reduce operator fatigue, allowing for longer work sessions without discomfort. The ergonomic control layout makes it easy to adjust settings on the fly, enhancing overall productivity and precision.

In addition to its mechanical advantages, the LZDS also incorporates sophisticated technologies aimed at optimizing the mowing process. The mower features a practical SmartPower system, which automatically adjusts the engine’s power output based on the load, ensuring optimal performance and fuel efficiency. This technology helps professionals achieve the best results while reducing operational costs.

Safety is a paramount consideration in the design of the LZDS, which includes features like a rollover protection system and easy-to-reach controls positioned for quick access. The mower’s durable design is complemented by easy-access maintenance points, making routine servicing straightforward.

In conclusion, the Exmark LZDS embodies the perfect fusion of innovation, power, and efficiency. With its high-performance engine, advanced cutting technology, and user-friendly features, it is tailored for professionals seeking reliable and effective solutions for lawn care. Whether it's maintaining expansive commercial properties or tackling intricate residential landscapes, the Exmark LZDS delivers outstanding performance that caters to the demanding needs of the landscaping industry.