Exmark LZDS manual Belt Guide Adjustment, Alternator Belt Tension, Parking Brake Adjustment

Page 42

Maintenance

 

 

 

 

 

Belt Guide Adjustment

 

 

1.

Stop engine, wait for all moving parts to stop, and

 

 

 

remove key. Engage parking brake.

 

 

2.

Remove the belt shield on the right side of mower

 

 

 

deck.

 

 

3.

Note belt guide bolted to deck near the shield

 

 

 

support stud and right-hand pulley. Guide should

 

 

 

be 1/8 inch (3.2 mm) away from the belt, with

 

 

 

bolt-end of guide near end of slot (Figure 21).

 

 

4.

If adjustment is necessary, loosen the bolt securing

 

 

 

the belt guide and make proper adjustment.

 

Figure 19

 

Tighten hardware.

1. Front of unit

2.

Alignment holes

 

 

 

Figure 20

1.

Spring idler pulley

3. Right side idler pulley

 

 

(adjustable)

2.

Front of unit

 

 

 

 

Alternator Belt Tension

Stop engine, wait for all moving parts to stop and remove key. Engage parking brake.

Tilt seat and remove air deflector panel

To tighten alternator belt, loosen both upper and lower alternator mounting bolts. Rotate alternator out, away from engine and retighten hardware to secure in place.

When properly tensioned, the alternator belt will deflect 1/4 to 3/8 inch (7-9 mm) while applying 22 pounds of force to the belt midway between fan and alternator.

Figure 21

1. End of slot

2. Belt guide

 

 

Parking Brake Adjustment

Service Interval: After the first 100 hours

Every 500 hours thereafter

Check to make sure brake is adjusted properly. This procedure must be followed after the first 100 hours or when a brake component has been removed or replaced.

1.Drive the machine onto a level surface.

2.Disengage the blade control switch (PTO), move the motion control levers to the neutral locked position and set the parking brake.

3.Stop the engine, wait for all moving parts to stop, and remove the key.

4.Raise the back of the machine up and support the machine with jack stands.

42

Image 42
Contents Lazer Z DS-SERIES California Introduction Contents Safe Operating Practices SafetySafety Alert Symbol TrainingOperation Slope Operation Using the Rollover Protection System Rops Maintenance and StorageSafety Safety Safety and Instructional Decals 103-0223 103-0261 103-1798 103-2076 103-7218 107-2102 109-0872 109-1214 109-1215 109-1399 109-2219 109-2263 109-2264 109-2478 109-2951 109-3148 117-2718 19426-87881 19426-87903 107-9866 Specifications Model NumbersSystems Tires & Wheels SeatHydrostatic Ground Drive System Cutting DeckDimensions Torque RequirementsControls Product OverviewOperation Motion Control LeversBrake Lever Ignition SwitchTracking Adjustment Knob Hour MeterPre-Start Raise the Rollover Protection System Rops Operating InstructionsBiodiesel Ready Open the Fuel Shut-Off ValveEngaging the PTO Disengaging the PTOStopping the Engine Driving the Machine Driving ForwardAdjusting the Cutting Height Adjusting the Anti-Scalp RollersTransporting Transporting a UnitLoading a Unit Operation Maintenance Recommended Maintenance SchedulesCheck Battery Charge Check Engine Oil LevelRecommended Jump Starting Procedure Check Mower Blades Engine Block of the StalledService Air Cleaner Check Safety Interlock SystemCheck Rollover Protections Systems Roll Bar Pins Check Seat BeltChange Engine Oil Check Hydraulic Oil LevelCheck Tire Pressures Check Condition Of Belts Lubricate Grease FittingsLubricate Brake Handle Pivot Wheel Hub Slotted Nut Torque SpecificationLubricate Caster Wheel Hubs Lubricate Brake Rod BushingsChange Fuel Filter/Water Separator Lubricate Motion Control Bronze BushingsDrain Fuel Filter/Water Separator Change Inline Fuel FilterCheck Engine Coolant Level Change Engine CoolantCheck Spark Arrester if equipped Thread Locking AdhesivesDielectric Grease Mobil HTS Grease Or Food-Grade Anti-seizeCopper-Based Anti-seize Deck LevelingMule Drive Belt Tension Adjustment Pump Drive Belt TensionDeck Belt Tension Belt Guide Adjustment Parking Brake AdjustmentAlternator Belt Tension Lever down Remove pin to adjust Disengaged Electric Clutch Adjustment Removing the ShimReverse Indicator Adjustment Motion Control Linkage AdjustmentBecause of the jumper wire being used. Run Motion Control Damper Adjustment Caster Pivot Bearings Pre-Load AdjustmentClean Engine Cooling System Clean Engine and Exhaust System AreaClean the Radiator Battery Disposal Clean Debris From MachineClean Grass Build-Up Under Deck Waste DisposalTroubleshooting Problem Possible Cause Corrective ActionTroubleshooting Troubleshooting Schematics Electrical DiagramElectrical Schematic Exmark Commercial Turf Equipment Page Service Record Date Description of Work Done Service Done ByPage This page may be copied for personal use See EXMARK’S Complete Line of Accessories and Options

LZDS specifications

The Exmark LZDS stands as a benchmark in the world of commercial lawn care equipment. Designed specifically for landscape professionals, the LZDS combines power, efficiency, and precision to deliver exceptional results in varied conditions. One of its hallmark features is the robust engine, engineered to handle large-scale mowing tasks without sacrificing reliability. The Exmark LZDS is equipped with a powerful Kohler Command Pro engine, which provides superior torque and smooth operation, making it ideal for tackling tough terrains.

The LZDS showcases Exmark’s signature UltraCut deck technology, which is designed to enhance cutting performance and deliver a clean, even cut. The deck comes in various sizes, allowing users to choose the perfect fit based on their specific mowing requirements. The heavy-duty construction ensures durability, while the unique design minimizes clumping and provides improved airflow, contributing to a flawless finish on every lawn.

One of the standout characteristics of the Exmark LZDS is its zero-turn capability. This feature allows for unparalleled maneuverability, enabling operators to navigate complex landscapes with ease. The intuitive controls and comfortable seating position reduce operator fatigue, allowing for longer work sessions without discomfort. The ergonomic control layout makes it easy to adjust settings on the fly, enhancing overall productivity and precision.

In addition to its mechanical advantages, the LZDS also incorporates sophisticated technologies aimed at optimizing the mowing process. The mower features a practical SmartPower system, which automatically adjusts the engine’s power output based on the load, ensuring optimal performance and fuel efficiency. This technology helps professionals achieve the best results while reducing operational costs.

Safety is a paramount consideration in the design of the LZDS, which includes features like a rollover protection system and easy-to-reach controls positioned for quick access. The mower’s durable design is complemented by easy-access maintenance points, making routine servicing straightforward.

In conclusion, the Exmark LZDS embodies the perfect fusion of innovation, power, and efficiency. With its high-performance engine, advanced cutting technology, and user-friendly features, it is tailored for professionals seeking reliable and effective solutions for lawn care. Whether it's maintaining expansive commercial properties or tackling intricate residential landscapes, the Exmark LZDS delivers outstanding performance that caters to the demanding needs of the landscaping industry.