Exmark LZDS manual Check Engine Oil Level, Check Battery Charge

Page 30

Maintenance

Maintenance Service

Maintenance Procedure

Interval

 

 

 

 

• Check the wheel hub slotted nut torque specifications.

Every 500 hours

• Check the wheel lug nuts.

• Change the hydraulic filter (Every 250 hours/yearly if using Mobil 1 15W50)

 

 

• Check the park brake adjustment.

 

 

Every 600 hours

• Replace the air cleaner elements. (May need more often under severe conditions. See the

Engine Owner's Manual for additional information.)

 

 

 

Every 4,000 hours

• Change engine coolant. Dex-Cool©extended life coolant (orange color)

Monthly

• Check the battery charge.

 

 

 

• Change the engine oil if operated less than 100 hours.

 

• Grease the front caster wheel hubs.

Yearly

• Grease front caster pivots.

• Grease the deck drive belt idler arm.

 

 

• Grease the mule drive belt idler arm.

 

• Grease the pump drive belt idler arm.

 

 

Periodic Maintenance

Check Engine Oil Level

Service Interval: Before each use or daily

1.Stop engine and wait for all moving parts to stop. Make sure unit is on a level surface.

2.Check with engine cold.

3.Raise radiator to gain access to dipstick.

CAUTION

If the radiator prop rod is not securely positioned in the notch the radiator may fall. Falling radiator could cause serious injury.

Be sure the prop rod is engaged securely in the notch at the far right side of the slot.

4.Clean area around dipstick. Remove dipstick and wipe oil off. Reinsert the dipstick and push it all the way down into the tube. Remove the dipstick and read the oil level.

5.If the oil level is low, wipe off the area around the oil fill cap, remove cap and fill to the “FULL” mark on the dipstick. Exmark 4-Cycle Premium Engine Oil is recommended; refer to the Engine Owner's manual for an acceptable alternative. Do Not overfill.

Important: Do Not operate the engine with the oil level below the “LOW” (or “ADD”) mark on the dipstick, or over the “FULL” mark.

Check Battery Charge

Service Interval: Monthly

WARNING

CALIFORNIA

Proposition 65 Warning

Battery posts, terminals, and related accessories contain lead and lead compounds, chemicals known to the State of California to cause cancer and reproductive harm. Wash hands after handling.

Allowing batteries to stand for an extended period of time without recharging them will result in reduced performance and service life. To preserve optimum battery performance and life, recharge batteries in storage when the open circuit voltage drops to 12.4 volts.

Note: To prevent damage due to freezing, battery should be fully charged before putting away for winter storage.

Check the voltage of the battery with a digital voltmeter. Locate the voltage reading of the battery in the table and charge the battery for the recommended time interval to bring the charge up to a full charge of 12.6 volts or greater.

Important: Make sure the negative battery cable is disconnected and the battery charger used for charging the battery has an output of 16 volts and

30

Image 30
Contents Lazer Z DS-SERIES California Introduction Contents Safe Operating Practices SafetySafety Alert Symbol TrainingOperation Slope Operation Using the Rollover Protection System Rops Maintenance and StorageSafety Safety Safety and Instructional Decals 103-0223 103-0261 103-1798 103-2076 103-7218 107-2102 109-0872 109-1214 109-1215 109-1399 109-2219 109-2263 109-2264 109-2478 109-2951 109-3148 117-2718 19426-87881 19426-87903 107-9866 Specifications Model NumbersSystems Tires & Wheels SeatHydrostatic Ground Drive System Cutting DeckDimensions Torque RequirementsControls Product OverviewOperation Motion Control LeversBrake Lever Ignition SwitchTracking Adjustment Knob Hour MeterPre-Start Raise the Rollover Protection System Rops Operating InstructionsBiodiesel Ready Open the Fuel Shut-Off ValveEngaging the PTO Disengaging the PTOStopping the Engine Driving the Machine Driving ForwardAdjusting the Cutting Height Adjusting the Anti-Scalp RollersTransporting Transporting a UnitLoading a Unit Operation Maintenance Recommended Maintenance SchedulesCheck Battery Charge Check Engine Oil LevelRecommended Jump Starting Procedure Check Mower Blades Engine Block of the StalledService Air Cleaner Check Safety Interlock SystemCheck Rollover Protections Systems Roll Bar Pins Check Seat BeltChange Engine Oil Check Hydraulic Oil LevelCheck Tire Pressures Check Condition Of Belts Lubricate Grease FittingsLubricate Brake Handle Pivot Wheel Hub Slotted Nut Torque SpecificationLubricate Caster Wheel Hubs Lubricate Brake Rod BushingsChange Fuel Filter/Water Separator Lubricate Motion Control Bronze BushingsDrain Fuel Filter/Water Separator Change Inline Fuel FilterCheck Engine Coolant Level Change Engine CoolantCheck Spark Arrester if equipped Thread Locking AdhesivesDielectric Grease Mobil HTS Grease Or Food-Grade Anti-seizeCopper-Based Anti-seize Deck LevelingMule Drive Belt Tension Adjustment Pump Drive Belt TensionDeck Belt Tension Belt Guide Adjustment Parking Brake AdjustmentAlternator Belt Tension Lever down Remove pin to adjust Disengaged Electric Clutch Adjustment Removing the ShimReverse Indicator Adjustment Motion Control Linkage AdjustmentBecause of the jumper wire being used. Run Motion Control Damper Adjustment Caster Pivot Bearings Pre-Load AdjustmentClean Engine Cooling System Clean Engine and Exhaust System AreaClean the Radiator Battery Disposal Clean Debris From MachineClean Grass Build-Up Under Deck Waste DisposalTroubleshooting Problem Possible Cause Corrective ActionTroubleshooting Troubleshooting Schematics Electrical DiagramElectrical Schematic Exmark Commercial Turf Equipment Page Service Record Date Description of Work Done Service Done ByPage This page may be copied for personal use See EXMARK’S Complete Line of Accessories and Options

LZDS specifications

The Exmark LZDS stands as a benchmark in the world of commercial lawn care equipment. Designed specifically for landscape professionals, the LZDS combines power, efficiency, and precision to deliver exceptional results in varied conditions. One of its hallmark features is the robust engine, engineered to handle large-scale mowing tasks without sacrificing reliability. The Exmark LZDS is equipped with a powerful Kohler Command Pro engine, which provides superior torque and smooth operation, making it ideal for tackling tough terrains.

The LZDS showcases Exmark’s signature UltraCut deck technology, which is designed to enhance cutting performance and deliver a clean, even cut. The deck comes in various sizes, allowing users to choose the perfect fit based on their specific mowing requirements. The heavy-duty construction ensures durability, while the unique design minimizes clumping and provides improved airflow, contributing to a flawless finish on every lawn.

One of the standout characteristics of the Exmark LZDS is its zero-turn capability. This feature allows for unparalleled maneuverability, enabling operators to navigate complex landscapes with ease. The intuitive controls and comfortable seating position reduce operator fatigue, allowing for longer work sessions without discomfort. The ergonomic control layout makes it easy to adjust settings on the fly, enhancing overall productivity and precision.

In addition to its mechanical advantages, the LZDS also incorporates sophisticated technologies aimed at optimizing the mowing process. The mower features a practical SmartPower system, which automatically adjusts the engine’s power output based on the load, ensuring optimal performance and fuel efficiency. This technology helps professionals achieve the best results while reducing operational costs.

Safety is a paramount consideration in the design of the LZDS, which includes features like a rollover protection system and easy-to-reach controls positioned for quick access. The mower’s durable design is complemented by easy-access maintenance points, making routine servicing straightforward.

In conclusion, the Exmark LZDS embodies the perfect fusion of innovation, power, and efficiency. With its high-performance engine, advanced cutting technology, and user-friendly features, it is tailored for professionals seeking reliable and effective solutions for lawn care. Whether it's maintaining expansive commercial properties or tackling intricate residential landscapes, the Exmark LZDS delivers outstanding performance that caters to the demanding needs of the landscaping industry.