Exmark LZDS manual Engaging the PTO, Disengaging the PTO, Stopping the Engine

Page 24

Operation

7.Turn ignition switch to the “ON” position. Depress the glow plug switch and the glow plug light will turn on. Hold switch as required by chart below. Turn the ignition switch to the “START” position. Release the ignition switch as soon as the engine starts.

Glow Plug Chart

Ambient Temperature

Hold Glow Plugs On

Above 50°F (10°C)

NO NEED

50°F (10°C) to 23°F (-5°C)

Approximately 5 seconds

Below 23°F (-5°C)

Approximately 10 seconds

 

 

Limit of continuous use

20 seconds

 

 

The glow plug light, located near the glow plug switch, will illuminate when the switch is depressed. The glow plug light indicates the glow plugs are preheating the combustion chamber.

Important: Do Not crank the engine continuously for more then ten seconds at a time. If the engine does not start, allow a 30 second cool-down period between starting attempts. Failure to follow these guidelines can burn out the starter motor and/or fuel solenoid.

8.Move the throttle to the “SLOW” (if in “MIDWAY”) and let the engine warm up a few minutes before moving the throttle to the “FAST” position.

Engaging the PTO

DANGER

The rotating blades under the mower deck are dangerous. Blade contact can cause serious injury or kill you.

Do Not put hands or feet under the mower or mower deck when the blades are engaged.

DANGER

An uncovered discharge opening will allow objects to be thrown in an operator’s or bystander’s direction. Also, contact with the blade could occur. Thrown objects or blade contact can cause serious injury or death.

Never operate the mower with the discharge deflector raised, removed, or altered unless there is a grass collection system or mulch kit in place and working properly.

The PTO push-pull switch engages the cutting blades. Be sure that all persons are clear of the mower deck and discharge area before engaging PTO.

Important: Operator must be in seat before the PTO can be engaged.

1.Set the throttle midway between the “SLOW” and “FAST” positions.

2.Pull the PTO switch outward to engage the blades.

3.Place the throttle in the “FAST” position to begin mowing.

Disengaging the PTO

1.Set the throttle midway between the “SLOW” and “FAST” positions.

2.Push the PTO switch in to disengage the blades.

Stopping the Engine

1.Bring the unit to a full stop.

2.Move the motion control levers out to the neutral lock position.

3.Engage the parking brake.

4.Place the throttle midway between the “SLOW” and “FAST” positions.

5.Disengage the PTO.

6.Allow the engine to run for a minimum of 15 seconds, then turn the ignition switch to the “OFF” position to stop the engine.

7.Remove the key to prevent children or other unauthorized persons from starting engine.

8.Close the fuel shut-off valve when the machine will not be in use for a few days, when transporting, or when the unit is parked inside a building.

24

Page 23 Page 25
Image 24
Page 23 Page 25
Contents Lazer Z DS-SERIES California Introduction Contents Safety Safety Alert SymbolSafe Operating Practices TrainingOperation Slope Operation Using the Rollover Protection System Rops Maintenance and StorageSafety Safety Safety and Instructional Decals 103-0223 103-0261 103-1798 103-2076 103-7218 107-2102 109-0872 109-1214 109-1215 109-1399 109-2219 109-2263 109-2264 109-2478 109-2951 109-3148 117-2718 19426-87881 19426-87903 107-9866 Specifications Model NumbersSystems Seat Hydrostatic Ground Drive SystemTires & Wheels Cutting DeckDimensions Torque RequirementsProduct Overview OperationControls Motion Control LeversIgnition Switch Tracking Adjustment KnobBrake Lever Hour MeterPre-Start Operating Instructions Biodiesel ReadyRaise the Rollover Protection System Rops Open the Fuel Shut-Off ValveEngaging the PTO Disengaging the PTOStopping the Engine Driving the Machine Driving ForwardAdjusting the Cutting Height Adjusting the Anti-Scalp RollersTransporting Transporting a UnitLoading a Unit Operation Maintenance Recommended Maintenance SchedulesCheck Battery Charge Check Engine Oil LevelRecommended Jump Starting Procedure Check Mower Blades Engine Block of the StalledCheck Safety Interlock System Check Rollover Protections Systems Roll Bar PinsService Air Cleaner Check Seat BeltChange Engine Oil Check Hydraulic Oil LevelCheck Tire Pressures Check Condition Of Belts Lubricate Grease FittingsWheel Hub Slotted Nut Torque Specification Lubricate Caster Wheel HubsLubricate Brake Handle Pivot Lubricate Brake Rod BushingsLubricate Motion Control Bronze Bushings Drain Fuel Filter/Water SeparatorChange Fuel Filter/Water Separator Change Inline Fuel FilterCheck Engine Coolant Level Change Engine CoolantCheck Spark Arrester if equipped Thread Locking AdhesivesMobil HTS Grease Or Food-Grade Anti-seize Copper-Based Anti-seizeDielectric Grease Deck LevelingMule Drive Belt Tension Adjustment Pump Drive Belt TensionDeck Belt Tension Belt Guide Adjustment Parking Brake AdjustmentAlternator Belt Tension Lever down Remove pin to adjust Disengaged Electric Clutch Adjustment Removing the ShimReverse Indicator Adjustment Motion Control Linkage AdjustmentBecause of the jumper wire being used. Run Motion Control Damper Adjustment Caster Pivot Bearings Pre-Load AdjustmentClean Engine Cooling System Clean Engine and Exhaust System AreaClean the Radiator Clean Debris From Machine Clean Grass Build-Up Under DeckBattery Disposal Waste DisposalTroubleshooting Problem Possible Cause Corrective ActionTroubleshooting Troubleshooting Schematics Electrical DiagramElectrical Schematic Exmark Commercial Turf Equipment Page Service Record Date Description of Work Done Service Done ByPage This page may be copied for personal use See EXMARK’S Complete Line of Accessories and Options

LZDS specifications

The Exmark LZDS stands as a benchmark in the world of commercial lawn care equipment. Designed specifically for landscape professionals, the LZDS combines power, efficiency, and precision to deliver exceptional results in varied conditions. One of its hallmark features is the robust engine, engineered to handle large-scale mowing tasks without sacrificing reliability. The Exmark LZDS is equipped with a powerful Kohler Command Pro engine, which provides superior torque and smooth operation, making it ideal for tackling tough terrains.

The LZDS showcases Exmark’s signature UltraCut deck technology, which is designed to enhance cutting performance and deliver a clean, even cut. The deck comes in various sizes, allowing users to choose the perfect fit based on their specific mowing requirements. The heavy-duty construction ensures durability, while the unique design minimizes clumping and provides improved airflow, contributing to a flawless finish on every lawn.

One of the standout characteristics of the Exmark LZDS is its zero-turn capability. This feature allows for unparalleled maneuverability, enabling operators to navigate complex landscapes with ease. The intuitive controls and comfortable seating position reduce operator fatigue, allowing for longer work sessions without discomfort. The ergonomic control layout makes it easy to adjust settings on the fly, enhancing overall productivity and precision.

In addition to its mechanical advantages, the LZDS also incorporates sophisticated technologies aimed at optimizing the mowing process. The mower features a practical SmartPower system, which automatically adjusts the engine’s power output based on the load, ensuring optimal performance and fuel efficiency. This technology helps professionals achieve the best results while reducing operational costs.

Safety is a paramount consideration in the design of the LZDS, which includes features like a rollover protection system and easy-to-reach controls positioned for quick access. The mower’s durable design is complemented by easy-access maintenance points, making routine servicing straightforward.

In conclusion, the Exmark LZDS embodies the perfect fusion of innovation, power, and efficiency. With its high-performance engine, advanced cutting technology, and user-friendly features, it is tailored for professionals seeking reliable and effective solutions for lawn care. Whether it's maintaining expansive commercial properties or tackling intricate residential landscapes, the Exmark LZDS delivers outstanding performance that caters to the demanding needs of the landscaping industry.
Top Page Image Contents