Exmark LZDS manual Clean Debris From Machine, Clean Grass Build-Up Under Deck, Waste Disposal

Page 49

Maintenance

Clean Debris From Machine

Service Interval: Before each use or daily

1.Stop engine, wait for all moving parts to stop, and remove key. Engage parking brake.

2.Clean off any oil, debris, or grass build-up on the machine and cutting deck, especially under deck belt shields, around the fuel tank, around engine and exhaust area.

Clean Grass Build-Up Under Deck

Service Interval: Before each use or daily

1.Stop engine, wait for all moving parts to stop, and remove key. Engage parking brake.

2.Raise deck to the transport (5 inch (12.7 cm) cutting height) position. Lift the front of unit and support unit using jack stands or equivalent support.

CAUTION

Raising the mower deck for service or maintenance relying solely on mechanical or hydraulic jacks could be dangerous. The mechanical or hydraulic jacks may not be enough support or may malfunction allowing the unit to fall, which could cause injury.

Do Not rely solely on mechanical or hydraulic jacks for support. Use adequate jack stands or equivalent support.

3.Clean out any grass build-up from underside of deck and in discharge deflector.

Waste Disposal

Motor Oil Disposal

Engine oil and hydraulic oil are both pollutants to the environment. Dispose of used oil at a certified recycling center or according to your state and local regulations.

Battery Disposal

DANGER

Battery electrolyte contains sulfuric acid, which is poisonous and can cause severe burns. Swallowing electrolyte can be fatal or if it touches skin can cause severe burns.

•Wear safety glasses to shield eyes, and rubber gloves to protect skin and clothing when handling electrolyte.

•Do Not swallow electrolyte.

•In the event of an accident, flush with water and call a doctor immediately.

Federal law states that batteries should not be placed in the garbage. Management and disposal practices must be within relevant federal, state, or local laws.

If a battery is being replaced or if the unit containing the battery is no longer operating and is being scrapped, take the battery to a local certified recycling center. If no local recycling is available return the battery to any certified battery reseller.

49

Page 48 Page 50
Image 49
Page 48 Page 50
Contents Lazer Z DS-SERIES California Introduction Contents Safety Alert Symbol SafetySafe Operating Practices TrainingOperation Slope Operation Maintenance and Storage Using the Rollover Protection System RopsSafety Safety Safety and Instructional Decals 103-0223 103-0261 103-1798 103-2076 103-7218 107-2102 109-0872 109-1214 109-1215 109-1399 109-2219 109-2263 109-2264 109-2478 109-2951 109-3148 117-2718 19426-87881 19426-87903 107-9866 Model Numbers SpecificationsSystems Hydrostatic Ground Drive System SeatTires & Wheels Cutting DeckTorque Requirements DimensionsOperation Product OverviewControls Motion Control LeversTracking Adjustment Knob Ignition SwitchBrake Lever Hour MeterPre-Start Biodiesel Ready Operating InstructionsRaise the Rollover Protection System Rops Open the Fuel Shut-Off ValveDisengaging the PTO Engaging the PTOStopping the Engine Driving Forward Driving the MachineAdjusting the Anti-Scalp Rollers Adjusting the Cutting HeightTransporting a Unit TransportingLoading a Unit Operation Recommended Maintenance Schedules MaintenanceCheck Engine Oil Level Check Battery ChargeRecommended Jump Starting Procedure Engine Block of the Stalled Check Mower BladesCheck Rollover Protections Systems Roll Bar Pins Check Safety Interlock SystemService Air Cleaner Check Seat BeltCheck Hydraulic Oil Level Change Engine OilCheck Tire Pressures Lubricate Grease Fittings Check Condition Of BeltsLubricate Caster Wheel Hubs Wheel Hub Slotted Nut Torque SpecificationLubricate Brake Handle Pivot Lubricate Brake Rod BushingsDrain Fuel Filter/Water Separator Lubricate Motion Control Bronze BushingsChange Fuel Filter/Water Separator Change Inline Fuel FilterChange Engine Coolant Check Engine Coolant LevelThread Locking Adhesives Check Spark Arrester if equippedCopper-Based Anti-seize Mobil HTS Grease Or Food-Grade Anti-seizeDielectric Grease Deck LevelingPump Drive Belt Tension Mule Drive Belt Tension AdjustmentDeck Belt Tension Parking Brake Adjustment Belt Guide AdjustmentAlternator Belt Tension Lever down Remove pin to adjust Disengaged Removing the Shim Electric Clutch AdjustmentMotion Control Linkage Adjustment Reverse Indicator AdjustmentBecause of the jumper wire being used. Run Caster Pivot Bearings Pre-Load Adjustment Motion Control Damper AdjustmentClean Engine and Exhaust System Area Clean Engine Cooling SystemClean the Radiator Clean Grass Build-Up Under Deck Clean Debris From MachineBattery Disposal Waste DisposalProblem Possible Cause Corrective Action TroubleshootingTroubleshooting Troubleshooting Electrical Diagram SchematicsElectrical Schematic Exmark Commercial Turf Equipment Page Date Description of Work Done Service Done By Service RecordPage This page may be copied for personal use See EXMARK’S Complete Line of Accessories and Options

LZDS specifications

The Exmark LZDS stands as a benchmark in the world of commercial lawn care equipment. Designed specifically for landscape professionals, the LZDS combines power, efficiency, and precision to deliver exceptional results in varied conditions. One of its hallmark features is the robust engine, engineered to handle large-scale mowing tasks without sacrificing reliability. The Exmark LZDS is equipped with a powerful Kohler Command Pro engine, which provides superior torque and smooth operation, making it ideal for tackling tough terrains.

The LZDS showcases Exmark’s signature UltraCut deck technology, which is designed to enhance cutting performance and deliver a clean, even cut. The deck comes in various sizes, allowing users to choose the perfect fit based on their specific mowing requirements. The heavy-duty construction ensures durability, while the unique design minimizes clumping and provides improved airflow, contributing to a flawless finish on every lawn.

One of the standout characteristics of the Exmark LZDS is its zero-turn capability. This feature allows for unparalleled maneuverability, enabling operators to navigate complex landscapes with ease. The intuitive controls and comfortable seating position reduce operator fatigue, allowing for longer work sessions without discomfort. The ergonomic control layout makes it easy to adjust settings on the fly, enhancing overall productivity and precision.

In addition to its mechanical advantages, the LZDS also incorporates sophisticated technologies aimed at optimizing the mowing process. The mower features a practical SmartPower system, which automatically adjusts the engine’s power output based on the load, ensuring optimal performance and fuel efficiency. This technology helps professionals achieve the best results while reducing operational costs.

Safety is a paramount consideration in the design of the LZDS, which includes features like a rollover protection system and easy-to-reach controls positioned for quick access. The mower’s durable design is complemented by easy-access maintenance points, making routine servicing straightforward.

In conclusion, the Exmark LZDS embodies the perfect fusion of innovation, power, and efficiency. With its high-performance engine, advanced cutting technology, and user-friendly features, it is tailored for professionals seeking reliable and effective solutions for lawn care. Whether it's maintaining expansive commercial properties or tackling intricate residential landscapes, the Exmark LZDS delivers outstanding performance that caters to the demanding needs of the landscaping industry.
Top Page Image Contents