Exmark LZDS manual Check Mower Blades, Engine Block of the Stalled

Page 32

Maintenance

Figure 13

1.Positive (+) cable on discharged battery

2.Positive (+) cable on booster battery

3.Negative (–) cable on the booster battery

4.Negative (–) cable on the engine block

5.Booster battery

6.Discharged battery

7.Engine block

Figure 14

1.Install bushing in blade prior to installing bushing in spindle.

B.Install bushing/blade assembly into spindle.

4.

Connect the other end of the positive cable to the

 

positive terminal of the booster battery.

5.

Connect the black negative (–) cable to the other

 

terminal (negative) of the booster battery.

6.

MAKE THE FINAL CONNECTION ON

 

THE ENGINE BLOCK OF THE STALLED

 

VEHICLE (NOT TO THE NEGATIVE POST)

Figure 15

AWAY FROM THE BATTERY. STAND BACK.

7. Start the vehicle and remove the cables in the

reverse order of connection (the engine block

(black) connection is the first to disconnect).

Check Mower Blades

1.Use wrench here for blade installation. This nut has been torqued to 90–110 ft-lb (122–149 N-m)

2.Torque to 55-60 ft-lb (75-81 N-m) Apply lubricant to threads as needed to prevent seizing. Copper-based anti-seize preferable. Grease acceptable substitute.

Service Interval: Before each use or daily

1.Stop engine, wait for all moving parts to stop, and remove key. Engage parking brake.

2.Lift deck and secure in raised position as stated in the Clean Grass Build-Up Under Deck procedure.

3.Inspect blades and sharpen or replace as required.

4.Reinstall the blades (if they were removed) in the following order:

A.Install bushing through blade with bushing flange on bottom (grass) side of blade.

C.Apply lubricant to threads of blade bolt as needed to prevent seizing. Copper-based anti-seize preferable. Grease acceptable substitute. Install blade bolt finger tight. Place wrench on the top spindle nut then torque the blade bolts to 55-60 ft-lb (75-81 N-m).

32

Page 31 Page 33
Image 32
Page 31 Page 33
Contents Lazer Z DS-SERIES California Introduction Contents Safety Safety Alert SymbolSafe Operating Practices TrainingOperation Slope Operation Using the Rollover Protection System Rops Maintenance and StorageSafety Safety Safety and Instructional Decals 103-0223 103-0261 103-1798 103-2076 103-7218 107-2102 109-0872 109-1214 109-1215 109-1399 109-2219 109-2263 109-2264 109-2478 109-2951 109-3148 117-2718 19426-87881 19426-87903 107-9866 Systems SpecificationsModel Numbers Seat Hydrostatic Ground Drive SystemTires & Wheels Cutting DeckDimensions Torque RequirementsProduct Overview OperationControls Motion Control LeversIgnition Switch Tracking Adjustment KnobBrake Lever Hour MeterPre-Start Operating Instructions Biodiesel ReadyRaise the Rollover Protection System Rops Open the Fuel Shut-Off ValveStopping the Engine Engaging the PTODisengaging the PTO Driving the Machine Driving ForwardAdjusting the Cutting Height Adjusting the Anti-Scalp RollersLoading a Unit TransportingTransporting a Unit Operation Maintenance Recommended Maintenance SchedulesCheck Battery Charge Check Engine Oil LevelRecommended Jump Starting Procedure Check Mower Blades Engine Block of the StalledCheck Safety Interlock System Check Rollover Protections Systems Roll Bar PinsService Air Cleaner Check Seat BeltCheck Tire Pressures Change Engine OilCheck Hydraulic Oil Level Check Condition Of Belts Lubricate Grease FittingsWheel Hub Slotted Nut Torque Specification Lubricate Caster Wheel HubsLubricate Brake Handle Pivot Lubricate Brake Rod BushingsLubricate Motion Control Bronze Bushings Drain Fuel Filter/Water SeparatorChange Fuel Filter/Water Separator Change Inline Fuel FilterCheck Engine Coolant Level Change Engine CoolantCheck Spark Arrester if equipped Thread Locking AdhesivesMobil HTS Grease Or Food-Grade Anti-seize Copper-Based Anti-seizeDielectric Grease Deck LevelingDeck Belt Tension Mule Drive Belt Tension AdjustmentPump Drive Belt Tension Alternator Belt Tension Belt Guide AdjustmentParking Brake Adjustment Lever down Remove pin to adjust Disengaged Electric Clutch Adjustment Removing the ShimReverse Indicator Adjustment Motion Control Linkage AdjustmentBecause of the jumper wire being used. Run Motion Control Damper Adjustment Caster Pivot Bearings Pre-Load AdjustmentClean the Radiator Clean Engine Cooling SystemClean Engine and Exhaust System Area Clean Debris From Machine Clean Grass Build-Up Under DeckBattery Disposal Waste DisposalTroubleshooting Problem Possible Cause Corrective ActionTroubleshooting Troubleshooting Schematics Electrical DiagramElectrical Schematic Exmark Commercial Turf Equipment Page Service Record Date Description of Work Done Service Done ByPage This page may be copied for personal use See EXMARK’S Complete Line of Accessories and Options

LZDS specifications

The Exmark LZDS stands as a benchmark in the world of commercial lawn care equipment. Designed specifically for landscape professionals, the LZDS combines power, efficiency, and precision to deliver exceptional results in varied conditions. One of its hallmark features is the robust engine, engineered to handle large-scale mowing tasks without sacrificing reliability. The Exmark LZDS is equipped with a powerful Kohler Command Pro engine, which provides superior torque and smooth operation, making it ideal for tackling tough terrains.

The LZDS showcases Exmark’s signature UltraCut deck technology, which is designed to enhance cutting performance and deliver a clean, even cut. The deck comes in various sizes, allowing users to choose the perfect fit based on their specific mowing requirements. The heavy-duty construction ensures durability, while the unique design minimizes clumping and provides improved airflow, contributing to a flawless finish on every lawn.

One of the standout characteristics of the Exmark LZDS is its zero-turn capability. This feature allows for unparalleled maneuverability, enabling operators to navigate complex landscapes with ease. The intuitive controls and comfortable seating position reduce operator fatigue, allowing for longer work sessions without discomfort. The ergonomic control layout makes it easy to adjust settings on the fly, enhancing overall productivity and precision.

In addition to its mechanical advantages, the LZDS also incorporates sophisticated technologies aimed at optimizing the mowing process. The mower features a practical SmartPower system, which automatically adjusts the engine’s power output based on the load, ensuring optimal performance and fuel efficiency. This technology helps professionals achieve the best results while reducing operational costs.

Safety is a paramount consideration in the design of the LZDS, which includes features like a rollover protection system and easy-to-reach controls positioned for quick access. The mower’s durable design is complemented by easy-access maintenance points, making routine servicing straightforward.

In conclusion, the Exmark LZDS embodies the perfect fusion of innovation, power, and efficiency. With its high-performance engine, advanced cutting technology, and user-friendly features, it is tailored for professionals seeking reliable and effective solutions for lawn care. Whether it's maintaining expansive commercial properties or tackling intricate residential landscapes, the Exmark LZDS delivers outstanding performance that caters to the demanding needs of the landscaping industry.
Top Page Image Contents