Exmark LZDS manual Recommended Maintenance Schedules

Page 29

Maintenance

Maintenance

Note: Determine the left and right sides of the machine from the normal operating position.

WARNING

While maintenance or adjustments are being made, someone could start the engine. Accidental starting of the engine could seriously injure you or other bystanders.

Remove the key from the ignition switch and engage parking brake before you do any maintenance.

WARNING

The engine can become very hot. Touching a hot engine can cause severe burns.

Allow the engine to cool completely before service or making repairs around the engine area.

Recommended Maintenance Schedule(s)

Maintenance Service

Maintenance Procedure

Interval

 

 

 

 

 

After the first 5 hours

•

Change the engine oil.

 

 

 

• Check the wheel hub slotted nut torque specifications.

After the first 100 hours

•

Check the wheel lug nuts.

 

• Check the park brake adjustment.

 

 

 

After the first 250 hours

•

Change the hydraulic filter.

 

 

 

• Check the engine oil level.

 

•

Check the mower blades.

 

• Check the safety interlock system.

 

• Check the rollover protections systems (roll bar) pins.

 

• Check the seat belt.

Before each use or daily

•

Check for loose hardware.

 

• Check engine coolant level.

 

• Clean the engine cooling system.

 

• Clean the engine and exhaust system area.

 

• Clean the grass and debris build-up from the machine and cutting deck.

 

• Clean the grass build-up from under the cutting deck.

 

 

 

• Check the hydraulic oil level.

 

• Check the tire pressures.

Every 40 hours

• Check the condition of the belts.

• Grease the height adjustment shaft bearings.

 

 

• Grease the rear deck struts.

 

• Drain fuel filter/water separator.

 

 

 

• Service the air cleaner. (May need more often under severe conditions. See the Engine

Every 50 hours

 

Owner's Manual for additional information.)

• Check spark arrester (if equipped).

 

 

• Clean the engine cooling system.

 

 

 

Every 100 hours

•

Change the engine oil. (May need more often under severe conditions.)

 

 

 

• Lubricate the brake handle pivot.

Every 160 hours

•

Lubricate the brake rod bushings.

 

• Lubricate the motion control bronze bushings.

 

 

 

Every 200 hours

•

Grease the brake brackets.

 

 

 

Every 400 hours

•

Replace the fuel filter/water separator (more often in dirty or dusty conditions).

 

 

 

29

Page 28 Page 30
Image 29
Page 28 Page 30
Contents Lazer Z DS-SERIES California Introduction Contents Safety Alert Symbol SafetySafe Operating Practices TrainingOperation Slope Operation Maintenance and Storage Using the Rollover Protection System RopsSafety Safety Safety and Instructional Decals 103-0223 103-0261 103-1798 103-2076 103-7218 107-2102 109-0872 109-1214 109-1215 109-1399 109-2219 109-2263 109-2264 109-2478 109-2951 109-3148 117-2718 19426-87881 19426-87903 107-9866 Systems SpecificationsModel Numbers Hydrostatic Ground Drive System SeatTires & Wheels Cutting DeckTorque Requirements DimensionsOperation Product OverviewControls Motion Control LeversTracking Adjustment Knob Ignition SwitchBrake Lever Hour MeterPre-Start Biodiesel Ready Operating InstructionsRaise the Rollover Protection System Rops Open the Fuel Shut-Off ValveStopping the Engine Engaging the PTODisengaging the PTO Driving Forward Driving the MachineAdjusting the Anti-Scalp Rollers Adjusting the Cutting HeightLoading a Unit TransportingTransporting a Unit Operation Recommended Maintenance Schedules MaintenanceCheck Engine Oil Level Check Battery ChargeRecommended Jump Starting Procedure Engine Block of the Stalled Check Mower BladesCheck Rollover Protections Systems Roll Bar Pins Check Safety Interlock SystemService Air Cleaner Check Seat BeltCheck Tire Pressures Change Engine OilCheck Hydraulic Oil Level Lubricate Grease Fittings Check Condition Of BeltsLubricate Caster Wheel Hubs Wheel Hub Slotted Nut Torque SpecificationLubricate Brake Handle Pivot Lubricate Brake Rod BushingsDrain Fuel Filter/Water Separator Lubricate Motion Control Bronze BushingsChange Fuel Filter/Water Separator Change Inline Fuel FilterChange Engine Coolant Check Engine Coolant LevelThread Locking Adhesives Check Spark Arrester if equippedCopper-Based Anti-seize Mobil HTS Grease Or Food-Grade Anti-seizeDielectric Grease Deck LevelingDeck Belt Tension Mule Drive Belt Tension AdjustmentPump Drive Belt Tension Alternator Belt Tension Belt Guide AdjustmentParking Brake Adjustment Lever down Remove pin to adjust Disengaged Removing the Shim Electric Clutch AdjustmentMotion Control Linkage Adjustment Reverse Indicator AdjustmentBecause of the jumper wire being used. Run Caster Pivot Bearings Pre-Load Adjustment Motion Control Damper AdjustmentClean the Radiator Clean Engine Cooling SystemClean Engine and Exhaust System Area Clean Grass Build-Up Under Deck Clean Debris From MachineBattery Disposal Waste DisposalProblem Possible Cause Corrective Action TroubleshootingTroubleshooting Troubleshooting Electrical Diagram SchematicsElectrical Schematic Exmark Commercial Turf Equipment Page Date Description of Work Done Service Done By Service RecordPage This page may be copied for personal use See EXMARK’S Complete Line of Accessories and Options

LZDS specifications

The Exmark LZDS stands as a benchmark in the world of commercial lawn care equipment. Designed specifically for landscape professionals, the LZDS combines power, efficiency, and precision to deliver exceptional results in varied conditions. One of its hallmark features is the robust engine, engineered to handle large-scale mowing tasks without sacrificing reliability. The Exmark LZDS is equipped with a powerful Kohler Command Pro engine, which provides superior torque and smooth operation, making it ideal for tackling tough terrains.

The LZDS showcases Exmark’s signature UltraCut deck technology, which is designed to enhance cutting performance and deliver a clean, even cut. The deck comes in various sizes, allowing users to choose the perfect fit based on their specific mowing requirements. The heavy-duty construction ensures durability, while the unique design minimizes clumping and provides improved airflow, contributing to a flawless finish on every lawn.

One of the standout characteristics of the Exmark LZDS is its zero-turn capability. This feature allows for unparalleled maneuverability, enabling operators to navigate complex landscapes with ease. The intuitive controls and comfortable seating position reduce operator fatigue, allowing for longer work sessions without discomfort. The ergonomic control layout makes it easy to adjust settings on the fly, enhancing overall productivity and precision.

In addition to its mechanical advantages, the LZDS also incorporates sophisticated technologies aimed at optimizing the mowing process. The mower features a practical SmartPower system, which automatically adjusts the engine’s power output based on the load, ensuring optimal performance and fuel efficiency. This technology helps professionals achieve the best results while reducing operational costs.

Safety is a paramount consideration in the design of the LZDS, which includes features like a rollover protection system and easy-to-reach controls positioned for quick access. The mower’s durable design is complemented by easy-access maintenance points, making routine servicing straightforward.

In conclusion, the Exmark LZDS embodies the perfect fusion of innovation, power, and efficiency. With its high-performance engine, advanced cutting technology, and user-friendly features, it is tailored for professionals seeking reliable and effective solutions for lawn care. Whether it's maintaining expansive commercial properties or tackling intricate residential landscapes, the Exmark LZDS delivers outstanding performance that caters to the demanding needs of the landscaping industry.
Top Page Image Contents