Exmark LZDS manual Check Condition Of Belts, Lubricate Grease Fittings

Page 35

Maintenance

2.Check tire pressure in drive tires.

3.Inflate drive tires to 10 psi (69 kPa).

4.Semi-pneumatic caster tires do not need to be inflated.

Note: Do Not add any type of tire liner or foam fill material to the tires. Excessive loads created by foam filled tires may cause failures to the hydro drive system, frame, and other components. Foam filling tires will void the warranty.

Check Condition Of Belts

Service Interval: Every 40 hours

1.Stop engine, wait for all moving parts to stop, and remove key. Engage parking brake.

2.Unhook seat latch and tilt seat up. Remove the air detector panel on front side of the engine compartment to check pump drive belt and alternator belt.

3.Remove left and right belt shields on deck and lift up floor pan to inspect deck drive belt.

4.Check under machine to inspect the mule drive belt. Refer to Mule Drive Belt Tension Adjustment section in Adjustments.

Lubricate Grease Fittings

Note: See chart for service intervals.

1.Stop engine, wait for all moving parts to stop, and remove key. Engage parking brake.

2.Lubricate fittings with one to two pumps of NGLI grade #2 multi-purpose gun grease.

Refer to the following chart for fitting locations and lubrication schedule.

Lubrication Chart

Fitting

Initial

Number of

Service

Locations

Pumps

Places

Interval

1. Front

*0

2

*Yearly

Caster wheel

 

 

 

hubs

 

 

 

2. Front

*0

2

*Yearly

Caster

 

 

 

Pivots

 

 

 

3. Height

1

5

40 Hours

Adjustment

 

 

 

Shaft

 

 

 

Bearings

 

 

 

Lubrication Chart

Fitting

Initial

Number of

Service

Locations

Pumps

Places

Interval

4. Deck

1

1

Yearly

Drive Belt

 

 

 

Idler Arm

 

 

 

5. Brake

1

2

200 Hours

Brackets

 

 

 

6. Mule

1

1

Yearly

Drive Belt

 

 

 

Idler Arm

 

 

 

7. Pump

1

1

Yearly

Drive Belt

 

 

 

Idler Arm

 

 

 

8. Deck

1

2

40 Hours

Rear Struts

 

 

 

*See step 3 for special lubrication instructions on the front caster pivots and the Lubricate Caster Wheel Hubs section for special lubrication instructions on the front casters wheel hubs.

Number 6 (Mule Drive Belt Idler Arm) Located

Under Engine Frame

Number 7 (Pump Drive Belt Idler Arm) Located

Under Engine Frame

3.Lubricate front caster pivots once a year. Remove hex plug and cap. Thread grease zerk in hole and pump with grease until it oozes out around top bearing. Remove grease zerk and thread plug back in. Place cap back on.

35

Image 35
Contents Lazer Z DS-SERIES California Introduction Contents Training SafetySafety Alert Symbol Safe Operating PracticesOperation Slope Operation Maintenance and Storage Using the Rollover Protection System RopsSafety Safety Safety and Instructional Decals 103-0223 103-0261 103-1798 103-2076 103-7218 107-2102 109-0872 109-1214 109-1215 109-1399 109-2219 109-2263 109-2264 109-2478 109-2951 109-3148 117-2718 19426-87881 19426-87903 107-9866 Systems SpecificationsModel Numbers Cutting Deck SeatHydrostatic Ground Drive System Tires & WheelsTorque Requirements DimensionsMotion Control Levers Product OverviewOperation ControlsHour Meter Ignition SwitchTracking Adjustment Knob Brake LeverPre-Start Open the Fuel Shut-Off Valve Operating InstructionsBiodiesel Ready Raise the Rollover Protection System RopsStopping the Engine Engaging the PTODisengaging the PTO Driving Forward Driving the MachineAdjusting the Anti-Scalp Rollers Adjusting the Cutting HeightLoading a Unit TransportingTransporting a Unit Operation Recommended Maintenance Schedules MaintenanceCheck Engine Oil Level Check Battery ChargeRecommended Jump Starting Procedure Engine Block of the Stalled Check Mower BladesCheck Seat Belt Check Safety Interlock SystemCheck Rollover Protections Systems Roll Bar Pins Service Air CleanerCheck Tire Pressures Change Engine OilCheck Hydraulic Oil Level Lubricate Grease Fittings Check Condition Of BeltsLubricate Brake Rod Bushings Wheel Hub Slotted Nut Torque SpecificationLubricate Caster Wheel Hubs Lubricate Brake Handle PivotChange Inline Fuel Filter Lubricate Motion Control Bronze BushingsDrain Fuel Filter/Water Separator Change Fuel Filter/Water SeparatorChange Engine Coolant Check Engine Coolant LevelThread Locking Adhesives Check Spark Arrester if equippedDeck Leveling Mobil HTS Grease Or Food-Grade Anti-seizeCopper-Based Anti-seize Dielectric GreaseDeck Belt Tension Mule Drive Belt Tension AdjustmentPump Drive Belt Tension Alternator Belt Tension Belt Guide AdjustmentParking Brake Adjustment Lever down Remove pin to adjust Disengaged Removing the Shim Electric Clutch AdjustmentMotion Control Linkage Adjustment Reverse Indicator AdjustmentBecause of the jumper wire being used. Run Caster Pivot Bearings Pre-Load Adjustment Motion Control Damper AdjustmentClean the Radiator Clean Engine Cooling SystemClean Engine and Exhaust System Area Waste Disposal Clean Debris From MachineClean Grass Build-Up Under Deck Battery DisposalProblem Possible Cause Corrective Action TroubleshootingTroubleshooting Troubleshooting Electrical Diagram SchematicsElectrical Schematic Exmark Commercial Turf Equipment Page Date Description of Work Done Service Done By Service RecordPage This page may be copied for personal use See EXMARK’S Complete Line of Accessories and Options

LZDS specifications

The Exmark LZDS stands as a benchmark in the world of commercial lawn care equipment. Designed specifically for landscape professionals, the LZDS combines power, efficiency, and precision to deliver exceptional results in varied conditions. One of its hallmark features is the robust engine, engineered to handle large-scale mowing tasks without sacrificing reliability. The Exmark LZDS is equipped with a powerful Kohler Command Pro engine, which provides superior torque and smooth operation, making it ideal for tackling tough terrains.

The LZDS showcases Exmark’s signature UltraCut deck technology, which is designed to enhance cutting performance and deliver a clean, even cut. The deck comes in various sizes, allowing users to choose the perfect fit based on their specific mowing requirements. The heavy-duty construction ensures durability, while the unique design minimizes clumping and provides improved airflow, contributing to a flawless finish on every lawn.

One of the standout characteristics of the Exmark LZDS is its zero-turn capability. This feature allows for unparalleled maneuverability, enabling operators to navigate complex landscapes with ease. The intuitive controls and comfortable seating position reduce operator fatigue, allowing for longer work sessions without discomfort. The ergonomic control layout makes it easy to adjust settings on the fly, enhancing overall productivity and precision.

In addition to its mechanical advantages, the LZDS also incorporates sophisticated technologies aimed at optimizing the mowing process. The mower features a practical SmartPower system, which automatically adjusts the engine’s power output based on the load, ensuring optimal performance and fuel efficiency. This technology helps professionals achieve the best results while reducing operational costs.

Safety is a paramount consideration in the design of the LZDS, which includes features like a rollover protection system and easy-to-reach controls positioned for quick access. The mower’s durable design is complemented by easy-access maintenance points, making routine servicing straightforward.

In conclusion, the Exmark LZDS embodies the perfect fusion of innovation, power, and efficiency. With its high-performance engine, advanced cutting technology, and user-friendly features, it is tailored for professionals seeking reliable and effective solutions for lawn care. Whether it's maintaining expansive commercial properties or tackling intricate residential landscapes, the Exmark LZDS delivers outstanding performance that caters to the demanding needs of the landscaping industry.