Exmark LZDS manual Check Engine Coolant Level, Change Engine Coolant

Page 38

Maintenance

6.Raise the rear of machine up and support with jack stands (or equivalent support) just high enough to allow drive wheels to turn freely.

7.Start engine and move throttle control ahead to full throttle position. Move the speed control levers to the full speed and run for several minutes. Shut down machine and recheck oil level.

Note: Do Not change hydraulic system oil (except for what can be drained when changing filter), unless it is felt the oil has been contaminated or been extremely hot.

Changing oil unnecessarily could damage hydraulic system by introducing contaminates into the system.

Check Engine Coolant Level

Service Interval: Before each use or daily

Note: If the engine coolant level is below the indicator line on the overflow bottle when the engine is cold, the coolant temperature gauge may not register correctly during operation and/or the warning buzzer may not sound if the engine overheats.

1.Stop engine and wait for all moving parts to stop. Make sure unit is on a level surface.

2.Check with engine cold.

3.View coolant level in overflow bottle on the left side of the engine compartment. Coolant level should be at the indicator line on the overflow bottle.

4.If the coolant level is low, open hood or raise radiator, remove the cap to the overflow bottle and fill to the indicator line. Units should only be filled with a 50/50 mix of Dex-Cool© extended life coolant and water. Dex-Cool© can be identified by its orange color.

WARNING

Engine coolant is hot and pressurized and radiator and surrounding parts are hot. Spray or steam from hot, pressurized liquid in the engine cooling system and touching a hot radiator may cause severe burns.

Allow the engine to cool completely before removing the radiator cap or servicing any component of the cooling system.

CAUTION

Engine coolant is toxic. Swallowing coolant can cause poisoning.

•Do Not swallow.

•Keep out of reach of children and pets.

Change Engine Coolant

Service Interval: Every 4,000 hours/Every 4 years (whichever comes first) Dex-Cool©extended life coolant (orange color)

1.Stop engine, wait for all moving parts to stop, and remove key. Engage parking brake. Machine must be positioned on level surface.

2.Unhook seat latch, tilt seat up and tilt hood forward to gain access to the cooling area. Do Not raise radiator, as it may not fully drain in that position.

WARNING

Engine coolant is hot and pressurized and radiator and surrounding parts are hot. Spray or steam from hot, pressurized liquid in the engine cooling system and touching a hot radiator may cause severe burns.

Allow the engine to cool completely before removing the radiator cap or servicing any component of the cooling system.

CAUTION

Engine coolant is toxic. Swallowing coolant can cause poisoning.

•Do Not swallow.

•Keep out of reach of children and pets.

3.Drain coolant when engine is cool. Coolant may be drained from the radiator by removing the drain plug in the right rear corner. The engine block may be drained by removing the rear radiator hose and/or by opening the drain cock on the right-hand side of the engine block (see Figure 17).

38

Page 37 Page 39
Image 38
Page 37 Page 39
Contents Lazer Z DS-SERIES California Introduction Contents Safe Operating Practices SafetySafety Alert Symbol TrainingOperation Slope Operation Using the Rollover Protection System Rops Maintenance and StorageSafety Safety Safety and Instructional Decals 103-0223 103-0261 103-1798 103-2076 103-7218 107-2102 109-0872 109-1214 109-1215 109-1399 109-2219 109-2263 109-2264 109-2478 109-2951 109-3148 117-2718 19426-87881 19426-87903 107-9866 Systems SpecificationsModel Numbers Tires & Wheels SeatHydrostatic Ground Drive System Cutting DeckDimensions Torque RequirementsControls Product OverviewOperation Motion Control LeversBrake Lever Ignition SwitchTracking Adjustment Knob Hour MeterPre-Start Raise the Rollover Protection System Rops Operating InstructionsBiodiesel Ready Open the Fuel Shut-Off ValveStopping the Engine Engaging the PTODisengaging the PTO Driving the Machine Driving ForwardAdjusting the Cutting Height Adjusting the Anti-Scalp RollersLoading a Unit TransportingTransporting a Unit Operation Maintenance Recommended Maintenance SchedulesCheck Battery Charge Check Engine Oil LevelRecommended Jump Starting Procedure Check Mower Blades Engine Block of the StalledService Air Cleaner Check Safety Interlock SystemCheck Rollover Protections Systems Roll Bar Pins Check Seat BeltCheck Tire Pressures Change Engine OilCheck Hydraulic Oil Level Check Condition Of Belts Lubricate Grease FittingsLubricate Brake Handle Pivot Wheel Hub Slotted Nut Torque SpecificationLubricate Caster Wheel Hubs Lubricate Brake Rod BushingsChange Fuel Filter/Water Separator Lubricate Motion Control Bronze BushingsDrain Fuel Filter/Water Separator Change Inline Fuel FilterCheck Engine Coolant Level Change Engine CoolantCheck Spark Arrester if equipped Thread Locking AdhesivesDielectric Grease Mobil HTS Grease Or Food-Grade Anti-seizeCopper-Based Anti-seize Deck LevelingDeck Belt Tension Mule Drive Belt Tension AdjustmentPump Drive Belt Tension Alternator Belt Tension Belt Guide AdjustmentParking Brake Adjustment Lever down Remove pin to adjust Disengaged Electric Clutch Adjustment Removing the ShimReverse Indicator Adjustment Motion Control Linkage AdjustmentBecause of the jumper wire being used. Run Motion Control Damper Adjustment Caster Pivot Bearings Pre-Load AdjustmentClean the Radiator Clean Engine Cooling SystemClean Engine and Exhaust System Area Battery Disposal Clean Debris From MachineClean Grass Build-Up Under Deck Waste DisposalTroubleshooting Problem Possible Cause Corrective ActionTroubleshooting Troubleshooting Schematics Electrical DiagramElectrical Schematic Exmark Commercial Turf Equipment Page Service Record Date Description of Work Done Service Done ByPage This page may be copied for personal use See EXMARK’S Complete Line of Accessories and Options

LZDS specifications

The Exmark LZDS stands as a benchmark in the world of commercial lawn care equipment. Designed specifically for landscape professionals, the LZDS combines power, efficiency, and precision to deliver exceptional results in varied conditions. One of its hallmark features is the robust engine, engineered to handle large-scale mowing tasks without sacrificing reliability. The Exmark LZDS is equipped with a powerful Kohler Command Pro engine, which provides superior torque and smooth operation, making it ideal for tackling tough terrains.

The LZDS showcases Exmark’s signature UltraCut deck technology, which is designed to enhance cutting performance and deliver a clean, even cut. The deck comes in various sizes, allowing users to choose the perfect fit based on their specific mowing requirements. The heavy-duty construction ensures durability, while the unique design minimizes clumping and provides improved airflow, contributing to a flawless finish on every lawn.

One of the standout characteristics of the Exmark LZDS is its zero-turn capability. This feature allows for unparalleled maneuverability, enabling operators to navigate complex landscapes with ease. The intuitive controls and comfortable seating position reduce operator fatigue, allowing for longer work sessions without discomfort. The ergonomic control layout makes it easy to adjust settings on the fly, enhancing overall productivity and precision.

In addition to its mechanical advantages, the LZDS also incorporates sophisticated technologies aimed at optimizing the mowing process. The mower features a practical SmartPower system, which automatically adjusts the engine’s power output based on the load, ensuring optimal performance and fuel efficiency. This technology helps professionals achieve the best results while reducing operational costs.

Safety is a paramount consideration in the design of the LZDS, which includes features like a rollover protection system and easy-to-reach controls positioned for quick access. The mower’s durable design is complemented by easy-access maintenance points, making routine servicing straightforward.

In conclusion, the Exmark LZDS embodies the perfect fusion of innovation, power, and efficiency. With its high-performance engine, advanced cutting technology, and user-friendly features, it is tailored for professionals seeking reliable and effective solutions for lawn care. Whether it's maintaining expansive commercial properties or tackling intricate residential landscapes, the Exmark LZDS delivers outstanding performance that caters to the demanding needs of the landscaping industry.
Top Page Image Contents