Exmark LZDS manual Seat, Hydrostatic Ground Drive System, Tires & Wheels, Cutting Deck

Page 18

Specifications

Moving motion control levers outward (in slots) locks the drive system in neutral.

PTO Engagement Switch: Engages electric clutch (to drive belt) which engages mower blades.

Parking Brake Lever: Engages parking brake.

Deck Height Adjustment Lever: Sets cutting height to desired position.

Deck Lift Assist Pedal: Foot pedal that assists in raising the deck.

Seat

Type: Deluxe suspension seat high back, low profile foam-in-place cushion (dampened, adjustable spring suspension) and armrests, adjustable back angle.

Mounting: Hinged to tilt up for access to hydraulic pumps, battery and other components. Held in tilted position with scissor—type links. Adjustable fore and aft seat track.

Armrests: Molded adjustable flip-up armrests.

Seat Safety Switch: Integrated seat switch. Time delay seat switch eliminates rough ground cut-outs.

Hydrostatic Ground Drive System

Hydrostatic Pumps: Two Hydro Gear PW variable displacement piston pumps.

Wheel Motors: Two Parker/Ross with 1 1/4 inch tapered shafts.

Hydraulic Oil Type: Exmark Premium Hydro oil.

Hydraulic Oil Capacity: 5.5 qt. (5.2 L)

Hydraulic Filter: Replaceable cartridge type.

P/N 103-2146: 25 microns, No bypass

Speeds:

0-12.0 mph (19.3 km/hr) forward.

0-8.0 mph (12.9 km/hr) reverse.

Drive wheel release valves allow machine to be moved when engine is not running.

Tires & Wheels

 

Drive

Front Caster

 

Pneumatic

Semi-Pneumatic

 

(Air-Filled)

 

Quantity

2

2

 

 

 

 

Drive

Front Caster

Tread Size

“Multi-Trac C/S”

Smooth

 

 

 

Size

26 x 12.00-12

13 x 6.50-6

Ply Rating

4

 

Pressure

10 psi (69 kPa)

 

 

 

 

Cutting Deck

Cutting Width:

60 inch (152.4 cm)

72 inch (182.9 cm)

Discharge: Side

Blade Size: (3 ea.)

60 inch Deck: 20.75 inches (52.7 cm)

72 inch Deck: 24.75 inches (62.9 cm)

Blade Spindles: Solid steel spindles with 1.18 inch (30 mm) I.D. bearings.

Deck Drive:

Electric clutch mounted on horizontal engine shaft. “B” Section belt (with self-tensioning idler) from electric clutch to transfer shaft mounted on deck.

Blades are driven by one “B” Section belt (w/self-tensioning idler) from transfer shaft on deck to blade spindles.

Deck:

Full floating deck is attached to out-front support frame. Six anti-scalp rollers provide maximum turf protection. Deck design allows for bagging, mulching or side discharge.

Deck Depth:

60 inch Deck: 6.0 inches (15.2 cm)

72 inch Deck: 6.0 inches (15.2 cm)

Cutting Height Adjustment:

An extra-long cushioned lever is used to adjust the cutting height from 1 inch (2.5 cm) to 5 inches (12.7 cm) in 1/4 inch (6.4 mm) increments. The cutting height adjustment handle has a transport position and all adjustments can be made while the operator remains seated. Units also have a foot operated deck lift assist lever to aid in raising the deck.

Mulching Kit: Optional.

18

Image 18
Contents Lazer Z DS-SERIES California Introduction Contents Safe Operating Practices SafetySafety Alert Symbol TrainingOperation Slope Operation Using the Rollover Protection System Rops Maintenance and StorageSafety Safety Safety and Instructional Decals 103-0223 103-0261 103-1798 103-2076 103-7218 107-2102 109-0872 109-1214 109-1215 109-1399 109-2219 109-2263 109-2264 109-2478 109-2951 109-3148 117-2718 19426-87881 19426-87903 107-9866 Specifications Model NumbersSystems Tires & Wheels SeatHydrostatic Ground Drive System Cutting DeckDimensions Torque RequirementsControls Product OverviewOperation Motion Control LeversBrake Lever Ignition SwitchTracking Adjustment Knob Hour MeterPre-Start Raise the Rollover Protection System Rops Operating InstructionsBiodiesel Ready Open the Fuel Shut-Off ValveEngaging the PTO Disengaging the PTOStopping the Engine Driving the Machine Driving ForwardAdjusting the Cutting Height Adjusting the Anti-Scalp RollersTransporting Transporting a UnitLoading a Unit Operation Maintenance Recommended Maintenance SchedulesCheck Battery Charge Check Engine Oil LevelRecommended Jump Starting Procedure Check Mower Blades Engine Block of the StalledService Air Cleaner Check Safety Interlock SystemCheck Rollover Protections Systems Roll Bar Pins Check Seat BeltChange Engine Oil Check Hydraulic Oil LevelCheck Tire Pressures Check Condition Of Belts Lubricate Grease FittingsLubricate Brake Handle Pivot Wheel Hub Slotted Nut Torque SpecificationLubricate Caster Wheel Hubs Lubricate Brake Rod BushingsChange Fuel Filter/Water Separator Lubricate Motion Control Bronze BushingsDrain Fuel Filter/Water Separator Change Inline Fuel FilterCheck Engine Coolant Level Change Engine CoolantCheck Spark Arrester if equipped Thread Locking AdhesivesDielectric Grease Mobil HTS Grease Or Food-Grade Anti-seizeCopper-Based Anti-seize Deck LevelingMule Drive Belt Tension Adjustment Pump Drive Belt TensionDeck Belt Tension Belt Guide Adjustment Parking Brake AdjustmentAlternator Belt Tension Lever down Remove pin to adjust Disengaged Electric Clutch Adjustment Removing the ShimReverse Indicator Adjustment Motion Control Linkage AdjustmentBecause of the jumper wire being used. Run Motion Control Damper Adjustment Caster Pivot Bearings Pre-Load AdjustmentClean Engine Cooling System Clean Engine and Exhaust System AreaClean the Radiator Battery Disposal Clean Debris From MachineClean Grass Build-Up Under Deck Waste DisposalTroubleshooting Problem Possible Cause Corrective ActionTroubleshooting Troubleshooting Schematics Electrical DiagramElectrical Schematic Exmark Commercial Turf Equipment Page Service Record Date Description of Work Done Service Done ByPage This page may be copied for personal use See EXMARK’S Complete Line of Accessories and Options

LZDS specifications

The Exmark LZDS stands as a benchmark in the world of commercial lawn care equipment. Designed specifically for landscape professionals, the LZDS combines power, efficiency, and precision to deliver exceptional results in varied conditions. One of its hallmark features is the robust engine, engineered to handle large-scale mowing tasks without sacrificing reliability. The Exmark LZDS is equipped with a powerful Kohler Command Pro engine, which provides superior torque and smooth operation, making it ideal for tackling tough terrains.

The LZDS showcases Exmark’s signature UltraCut deck technology, which is designed to enhance cutting performance and deliver a clean, even cut. The deck comes in various sizes, allowing users to choose the perfect fit based on their specific mowing requirements. The heavy-duty construction ensures durability, while the unique design minimizes clumping and provides improved airflow, contributing to a flawless finish on every lawn.

One of the standout characteristics of the Exmark LZDS is its zero-turn capability. This feature allows for unparalleled maneuverability, enabling operators to navigate complex landscapes with ease. The intuitive controls and comfortable seating position reduce operator fatigue, allowing for longer work sessions without discomfort. The ergonomic control layout makes it easy to adjust settings on the fly, enhancing overall productivity and precision.

In addition to its mechanical advantages, the LZDS also incorporates sophisticated technologies aimed at optimizing the mowing process. The mower features a practical SmartPower system, which automatically adjusts the engine’s power output based on the load, ensuring optimal performance and fuel efficiency. This technology helps professionals achieve the best results while reducing operational costs.

Safety is a paramount consideration in the design of the LZDS, which includes features like a rollover protection system and easy-to-reach controls positioned for quick access. The mower’s durable design is complemented by easy-access maintenance points, making routine servicing straightforward.

In conclusion, the Exmark LZDS embodies the perfect fusion of innovation, power, and efficiency. With its high-performance engine, advanced cutting technology, and user-friendly features, it is tailored for professionals seeking reliable and effective solutions for lawn care. Whether it's maintaining expansive commercial properties or tackling intricate residential landscapes, the Exmark LZDS delivers outstanding performance that caters to the demanding needs of the landscaping industry.