Exmark Lazer Z XS manual Service Battery, Upper Roll BAR Installation

Page 20

FIGURE 3

UPPER ROLL BAR INSTALLATION

3.3 SERVICE BATTERY

WARNING: Battery posts, terminals, and related accessories contain lead compounds, chemicals known to the State of California to cause cancer and reproductive harm. Wash hands after handling.

The machine is shipped with a filled lead acid battery.

3.3.1Unhook seat latch and tilt seat up to gain access to the battery.

DANGER

POTENTIAL HAZARD

Charging the battery may produce explosive gasses

WHAT CAN HAPPEN

Battery gasses can explode causing serious injury.

HOW TO AVOID THE HAZARD

Keep sparks, flames, or cigarettes away from battery.

Ventilate when charging or using battery in an enclosed space.

Make sure venting path of battery is always open once battery is filled with acid.

3.3.2Check the voltage of the battery with a digital voltmeter. Locate the voltage reading of the battery in the table below and charge the battery for the recommended time interval to bring the charge up to a full charge of 12.6 volts or greater.

IMPORTANT: Make sure the negative battery cables are disconnected and the battery charger used for charging the battery has an output of 16 volts and 7 amps or less to avoid damaging the battery (see the following chart for recommended charger settings).

Voltage

Percent

 

Maximum

 

Charging Interval

Reading

Charge

 

Charger Settings

 

 

 

 

12.6 or greater

100%

 

16 volts/7 amps

No Charging Required

12.4 – 12.6

75

– 100%

 

16 volts/7 amps

30 Minutes

12.2 – 12.4

50

– 75%

 

16 volts/7 amps

1

Hour

12.0 – 12.2

25

– 50%

 

14.4 volts/4 amps

2

Hours

11.7 – 12.0

0 – 25%

 

14.4 volts/4 amps

3

Hours

11.7 or less

0%

 

14.4 volts/2 amps

6

Hours or More

 

 

 

- 15 -

 

 

Image 20
Contents For Serial Nos 440,000 & Higher Potential Hazard Exmark Parts PLUS→ Program Operators Manual Table of Contents Safety Your Safety is InvolvedSafety Alert Symbol TrainingCarbon monoxide can kill you Potential Hazard Operation Safe Zone for Mowing There is no rollover protection when the roll bar is down Maintenance and Storage Safety Signs Do not Operate Without Guard Location Rubber Heat Shield Specifications Cutting Deck Hydrostatic Ground Drive SystemTires Assembly Instructions DimensionsUncrate Mower Install Rollover Protection System Roll BAR Torque RequirementsLower Roll BAR Installation Machine is shipped with a filled lead acid battery Service BatteryUpper Roll BAR Installation Install Seat Install Motion Control LeversCheck Tire Pressure Service Engine Service Hydraulic OILPosition Discharge Chute Motion Control Positions Operation InstructionsControls Push the lever forward and down to disengage the brake PRE-START Operating InstructionsRotating blades under the mower deck are dangerous Transporting Service Interval Daily Maintenance & AdjustmentsPeriodic Maintenance Service Interval Monthly Service Interval Daily or more often in dry conditionsService Interval Daily Blade Bolt Installation Check rollover protections systems roll bar pins Service Interval Refer to chart Service Interval 40 hrService Interval 40 hrs Caster Wheel Assembly Lubrication ChartService Interval Once Yearly Service Interval 160 hrs Service Interval 500 hrs Service Interval As RequiredService Interval After First 250 hrs Then yearly thereafter Adjustments Cutting Height PositionANTI-SCALP Roller Adjustment Swivel Adjustment Spring Compression Adjustment Self-tensioning No adjustment necessaryMule Drive Belt Adjustment Belt Guide PositioningThrottle Tension Brake AdjustmentNo adjustment necessary Reverse Indicator Adjustment Motion Control Adjustment Mercury Switch Disposal Caster AdjustmentWaste Disposal Motor OIL DisposalTrouble Shooting Battery DisposalMower Pulls Left or Right W/LEVERS Fully Forward Mower Cuts UnevenlyEngine Troubleshooting Table ProblemElectrical Diagram Hydraulic Diagram Limited Warranty Exmark Turf Equipment Service Record Page See EXMARK’S Complete Line of Products for Turf Care