Exmark Lazer Z XS manual Adjustments, Cutting Height Position

Page 37

5.1.24Fuel Tank – mounting hardware specification.

When installing the nuts on the fuel tank studs, fully tighten the nyloc nut and back off 1/2 turn. This allows for normal fuel tank expansion and contraction with changes in temperature and fuel levels.

5.1.25Thread locking adhesives such as “Loctite 242” or “Fel-Pro, Pro-Lock Nut Type” are used on the following fasteners:

a)Pump drive sheave set screws.

b)Square head setscrews on Hydro pump control arms.

c)Sheave retaining bolt in the end of engine crankshaft.

d)Caster wheel spacer nuts

e)Fuel tank bulkhead fitting nuts.

Adhesives such as “Loctite RC/609 or RC/680” or “Fel-Pro Pro-Lock Retaining I or Retaining II” are used on the following:

a)Fuel tank studs, where studs are inserted into tank.

5.1.26Mobil HTS grease (or food-grade antisieze) is used in the following locations:

a)Between the cutter housing spindle and bearings.

b)Between the cutter housing spindle and sheave.

c)Under top cutter housing bearing guard.

d)Between jackshaft and bearings and jackshaft and sheaves.

5.1.27Dielectric grease is used on all blade type electrical connections to prevent corrosion and loss of contact.

5.2 ADJUSTMENTS

IMPORTANT: Disengage PTO, shut off engine, wait for all moving parts to stop, and remove key before servicing, cleaning, or making any adjustments to the unit.

5.2.1Cutting Height Adjustment.

a)Stop machine and move drive levers out to neutral lock position.

b)Disengage PTO.

c)Raise the deck lever to the transport position (also the 5” (12.7 cm) cutting height position). See Figure 9.

The deck can be raised by pulling the deck lever up and/or by pushing on the deck lift assist lever.

NOTE: When changing cutting height positions, always come to a complete stop and disengage the PTO.

FIGURE 9

CUTTING HEIGHT POSITION

d)Insert height adjustment pin into hole corresponding to desired cutting height and install hairpin cotter. See decal on the side of deck lift plate.

- 32 -

Image 37
Contents For Serial Nos 440,000 & Higher Potential Hazard Exmark Parts PLUS→ Program Operators Manual Table of Contents Your Safety is Involved SafetySafety Alert Symbol TrainingCarbon monoxide can kill you Potential Hazard Operation Safe Zone for Mowing There is no rollover protection when the roll bar is down Maintenance and Storage Safety Signs Do not Operate Without Guard Location Rubber Heat Shield Specifications Tires Hydrostatic Ground Drive SystemCutting Deck Dimensions Assembly InstructionsUncrate Mower Install Rollover Protection System Roll BAR Torque RequirementsLower Roll BAR Installation Upper Roll BAR Installation Service BatteryMachine is shipped with a filled lead acid battery Install Motion Control Levers Install SeatPosition Discharge Chute Service Engine Service Hydraulic OILCheck Tire Pressure Controls Operation InstructionsMotion Control Positions Push the lever forward and down to disengage the brake Operating Instructions PRE-STARTRotating blades under the mower deck are dangerous Transporting Periodic Maintenance Maintenance & AdjustmentsService Interval Daily Service Interval Daily or more often in dry conditions Service Interval MonthlyService Interval Daily Blade Bolt Installation Check rollover protections systems roll bar pins Service Interval 40 hrs Service Interval 40 hrService Interval Refer to chart Service Interval Once Yearly Lubrication ChartCaster Wheel Assembly Service Interval 160 hrs Service Interval After First 250 hrs Then yearly thereafter Service Interval As RequiredService Interval 500 hrs Cutting Height Position AdjustmentsANTI-SCALP Roller Adjustment Self-tensioning No adjustment necessary Swivel Adjustment Spring Compression AdjustmentBelt Guide Positioning Mule Drive Belt AdjustmentNo adjustment necessary Brake AdjustmentThrottle Tension Reverse Indicator Adjustment Motion Control Adjustment Caster Adjustment Mercury Switch DisposalWaste Disposal Motor OIL DisposalBattery Disposal Trouble ShootingMower Pulls Left or Right W/LEVERS Fully Forward Mower Cuts UnevenlyProblem Engine Troubleshooting TableElectrical Diagram Hydraulic Diagram Limited Warranty Exmark Turf Equipment Service Record Page See EXMARK’S Complete Line of Products for Turf Care