Exmark Lazer Z XS manual Position Discharge Chute, Service Engine Service Hydraulic OIL

Page 22

MOTION

CONTROL LEVER

MOUNT PLATE TO

THE REAR & OUTSIDE

OF ARM SHAFT

LEVERS IN

ALIGNMENT

FIGURE 4

FIGURE 5

CONTROL ARM SHAFT

LEVER ALIGNMENT

b)If the ends of the levers hit against each other, while in the drive position (levers rotated in as far as possible), make adjustments by moving the levers outwards to the neutral lock position and carefully bend them outward. Move them back to the drive position and check for clearance, repeat if necessary.

3.6POSITION DISCHARGE CHUTE.

Loosen two (2) 5/16” nyloc nuts attaching discharge chute. Lower the discharge chute into position. Retighten nyloc nuts until chute is snug but can pivot freely.

3.7SERVICE ENGINE.

Engine is shipped with oil; check oil level and if necessary and fill to the appropriate level with oil as specified in Engine Owner’s Manual.

3.8SERVICE HYDRAULIC OIL

The machine is shipped with hydraulic oil in the reservoir. Run the machine for approximately 15 minutes to allow any extra air to purge out of the hydraulic system. Check hydraulic reservoir and if necessary fill the reservoir to the appropriate level with Mobil 1 15W-50 synthetic motor oil. Replace hydraulic reservoir cap and tighten until snug. DO NOT overtighten.

NOTE: The baffle has two levels. The upper level represents the “HOT” level and the lower level represents the “COLD” level. The oil level varies with the temperature of the oil. The “HOT” level shows the level of oil when it is a 225°F (107°C). The “COLD” level shows the level of the oil when it is at 75°F (24°C). Fill to the appropriate level depending upon the temperature of the oil. For example: If the oil is about 150°F (65°C), fill to halfway between the “HOT” and “COLD” levels. If the oil is at room temperature (about 75°F (24°C)), fill only to the “COLD” level.

3.9CHECK TIRE PRESSURE.

Check tire pressure in drive tires. Proper inflation pressure for the drive tires is 10 psi (90 kPa). Adjust if necessary. Semi-Pneumatic Caster tires (without a valve stem) do not need to be inflated.

NOTE: Perform the following steps if the unit is to be driven off of the crate.

a)Remove the crating strap from the rear of the unit.

b)Inflate the rear drive tires to approximately 25 psi to lift the frame of the unit off the rear crating brackets.

c)Read Section 4 (Operation Instructions) before driving the unit off the crate bottom.

d)After removing the unit from the crate, re-set the air pressure in the drive tires to 10 psi.

-17 -

Image 22
Contents For Serial Nos 440,000 & Higher Potential Hazard Exmark Parts PLUS→ Program Operators Manual Table of Contents Safety Alert Symbol SafetyYour Safety is Involved TrainingCarbon monoxide can kill you Potential Hazard Operation Safe Zone for Mowing There is no rollover protection when the roll bar is down Maintenance and Storage Safety Signs Do not Operate Without Guard Location Rubber Heat Shield Specifications Tires Hydrostatic Ground Drive SystemCutting Deck Uncrate Mower Install Rollover Protection System Roll BAR Assembly InstructionsDimensions Torque RequirementsLower Roll BAR Installation Upper Roll BAR Installation Service BatteryMachine is shipped with a filled lead acid battery Install Seat Install Motion Control LeversPosition Discharge Chute Service Engine Service Hydraulic OILCheck Tire Pressure Controls Operation InstructionsMotion Control Positions Push the lever forward and down to disengage the brake PRE-START Operating InstructionsRotating blades under the mower deck are dangerous Transporting Periodic Maintenance Maintenance & AdjustmentsService Interval Daily Service Interval Monthly Service Interval Daily or more often in dry conditionsService Interval Daily Blade Bolt Installation Check rollover protections systems roll bar pins Service Interval 40 hrs Service Interval 40 hrService Interval Refer to chart Service Interval Once Yearly Lubrication ChartCaster Wheel Assembly Service Interval 160 hrs Service Interval After First 250 hrs Then yearly thereafter Service Interval As RequiredService Interval 500 hrs Adjustments Cutting Height PositionANTI-SCALP Roller Adjustment Swivel Adjustment Spring Compression Adjustment Self-tensioning No adjustment necessaryMule Drive Belt Adjustment Belt Guide PositioningNo adjustment necessary Brake AdjustmentThrottle Tension Reverse Indicator Adjustment Motion Control Adjustment Waste Disposal Mercury Switch DisposalCaster Adjustment Motor OIL DisposalMower Pulls Left or Right W/LEVERS Fully Forward Trouble ShootingBattery Disposal Mower Cuts UnevenlyEngine Troubleshooting Table ProblemElectrical Diagram Hydraulic Diagram Limited Warranty Exmark Turf Equipment Service Record Page See EXMARK’S Complete Line of Products for Turf Care