2.10 DIMENSIONS
2.10.1 Overall Width: |
| without deck | deflector up |
| deflector down |
| |
|
|
|
|
|
|
| |
| 60” Deck |
| 54.5 in. (138.4 cm) | 61.4 in. (156.0 cm) | 72.2 in. (183.4 cm) |
| |
| 72” Deck |
| 58.5 in. (148.6 cm) | 73.2 in. (185.9 cm) | 84.3 in. (214.1 cm) |
| |
|
|
|
|
| |||
2.10.2 Overall Length: |
| Roll Bar – Up | Roll Bar - Down |
|
| ||
|
|
|
|
|
|
| |
| 60” Deck |
| 82.2 in. (208.8 cm) | 92.3 in. (234.4 cm) |
|
| |
| 72” Deck |
| 86.0 in. (218.4 cm) | 96.1 in. (244.1 cm) |
|
| |
|
|
|
|
| |||
2.10.3 Overall Height: |
| Roll Bar - Up | Roll Bar - Down |
|
| ||
|
|
|
|
|
|
| |
| 60” Deck |
| 73.7 in. (187.2 cm) | 55.6 in. (141.2 cm) |
|
| |
| 72” Deck |
| 73.7 in. (187.2 cm) | 55.6 in. (141.2 cm) |
|
| |
2.10.4 Tread Width: (center to center of tires, widthwise) |
|
|
| ||||
|
|
|
|
|
|
|
|
|
|
| Drive Wheels | Casters |
|
|
|
| 60” Deck |
| 42.8 in. (108.7 cm) | 38.9 in. (98.8 cm) |
|
| |
| 72” Deck |
| 46.8 in. (118.9 cm) | 47.6 in. (120.9 cm) |
|
| |
2.10.5 Wheel Base: (center of caster to center of drive tire) |
|
|
| ||||
|
|
|
|
|
|
| |
| 60” Deck |
| 54.0 in. (137.2 cm) |
|
|
|
|
| 72” Deck |
| 56.8 in. (144.3 cm) |
|
|
|
|
2.10.6 Curb Weight: |
|
|
|
|
| ||
|
|
|
|
|
|
| |
| 60” Deck |
| 1450 lbs. (658 kg) |
|
|
|
|
| 72” Deck |
| 1520 lbs. (689 kg) |
|
|
|
|
2.11 TORQUE REQUIREMENTS |
|
|
|
| |||
Bolt Location |
|
|
| Torque | |||
Cutter Housing Spindle Nut | |||||||
Blade Mounting Bolt | |||||||
Engine Deck/Front Frame Mount Bolts |
| ||||||
| |||||||
Engine Mounting Bolts | ....................................................... |
| |||||
Wheel Lug Nuts | |||||||
Wheel Motor Mounting Bolts |
| ||||||
Wheel Hub Slotted Nut | .............................................. | minimum 125 | |||||
Rollover Protection System (Roll Bar) Mounting Bolts |
3.ASSEMBLY INSTRUCTIONS
3.1UNCRATE MOWER
3.2INSTALL ROLLOVER PROTECTION SYSTEM (ROLL BAR)
3.2.1Disassemble roll bar from the crate.
a)Remove roll bar tubes from sides of crate.
b)Remove the two brackets used to mount the bottom of the upper roll bar tube to the crate. Remove the
3.2.2Install the two lower roll bar tubes.
a)Locate the left and right lower roll bar tubes.
b)Align lower roll bar tubes along wheel motor channels as shown in Figure 2.
-13 -