Exmark Lazer Z XS manual Service Interval Daily

Page 30

CAUTION

POTENTIAL HAZARD

Raising the mower deck for service or maintenance relying solely on mechanical or hydraulic jacks could be dangerous.

WHAT CAN HAPPEN

The mechanical or hydraulic jacks may not be enough support or may malfunction allowing the unit to fall, which could cause injury.

HOW TO AVOID THE HAZARD

DO NOT rely solely on mechanical or hydraulic jacks for support. Use adequate jack stands or equivalent support.

c)Clean out any grass build-up from underside of deck and in discharge chute.

5.1.5Check mower blades.

Service Interval: Daily

a)Stop engine, wait for all moving parts to stop, and remove key.

b)Lift deck and secure in raised position as stated in Section 5.1.4.

c)Inspect blades and sharpen or replace as required.

d)Re-install the blades (if they were removed) by placing a block of wood between the front or rear baffles and the blade then torque the blade bolts to 115-120 ft-lbs. (156-163 N-m). Be sure the spring disk washer cone is installed toward the bolt head (See Figure 7).

CAUTION

POTENTIAL HAZARD

Operating a mower deck with loose or weakened blade bolts can be dangerous.

WHAT CAN HAPPEN

A loose or weakened blade bolt could allow a blade rotating at a high speed to come out from under the deck, causing serious injury or property damage.

HOW TO AVOID THE HAZARD

Replace the blade bolt after striking a foreign object. Use only the following replacement parts:

Blade bolt – PN 103-0862

Spring disc washer – PN 103-0865

DO NOT lubricate the threads of the bolt or spindle before assembly.

Torque the blade bolt to 115-120 ft. lbs. (156-163 N-m)

- 25 -

Image 30
Contents For Serial Nos 440,000 & Higher Potential Hazard Exmark Parts PLUS→ Program Operators Manual Table of Contents Safety Alert Symbol SafetyYour Safety is Involved TrainingCarbon monoxide can kill you Potential Hazard Operation Safe Zone for Mowing There is no rollover protection when the roll bar is down Maintenance and Storage Safety Signs Do not Operate Without Guard Location Rubber Heat Shield Specifications Hydrostatic Ground Drive System TiresCutting Deck Uncrate Mower Install Rollover Protection System Roll BAR Assembly InstructionsDimensions Torque RequirementsLower Roll BAR Installation Service Battery Upper Roll BAR InstallationMachine is shipped with a filled lead acid battery Install Seat Install Motion Control LeversService Engine Service Hydraulic OIL Position Discharge ChuteCheck Tire Pressure Operation Instructions ControlsMotion Control Positions Push the lever forward and down to disengage the brake PRE-START Operating InstructionsRotating blades under the mower deck are dangerous Transporting Maintenance & Adjustments Periodic MaintenanceService Interval Daily Service Interval Monthly Service Interval Daily or more often in dry conditionsService Interval Daily Blade Bolt Installation Check rollover protections systems roll bar pins Service Interval 40 hr Service Interval 40 hrsService Interval Refer to chart Lubrication Chart Service Interval Once YearlyCaster Wheel Assembly Service Interval 160 hrs Service Interval As Required Service Interval After First 250 hrs Then yearly thereafterService Interval 500 hrs Adjustments Cutting Height PositionANTI-SCALP Roller Adjustment Swivel Adjustment Spring Compression Adjustment Self-tensioning No adjustment necessaryMule Drive Belt Adjustment Belt Guide PositioningBrake Adjustment No adjustment necessaryThrottle Tension Reverse Indicator Adjustment Motion Control Adjustment Waste Disposal Mercury Switch DisposalCaster Adjustment Motor OIL DisposalMower Pulls Left or Right W/LEVERS Fully Forward Trouble ShootingBattery Disposal Mower Cuts UnevenlyEngine Troubleshooting Table ProblemElectrical Diagram Hydraulic Diagram Limited Warranty Exmark Turf Equipment Service Record Page See EXMARK’S Complete Line of Products for Turf Care