Exmark Lazer Z XS manual Install Seat, Install Motion Control Levers

Page 21

CAUTION

POTENTIAL HAZARD

♦If the ignition is in the “ON” position there is potential for sparks and engagement of components.

WHAT CAN HAPPEN

♦Sparks could cause an explosion or moving parts could accidentally engage causing personal injury.

HOW TO AVOID THE HAZARD

♦Be sure ignition switch is in the “OFF” position before charging the battery.

3.3.3Connect the negative battery cables.

NOTE: If the positive cable is also disconnected, connect the positive (red) cable and the red wire to the positive terminal on the battery first, then connect the negative (black) cable and white/white wire to the negative terminal on the battery (red wire and white/white wire are only on some units). Slip insulator boot over the positive terminal.

NOTE: If time does not permit charging the battery, or if charging equipment is not available, connect the negative battery cables and run the vehicle continuously for 20 to 30 minutes to sufficiently charge the battery.

3.4INSTALL SEAT

a)Remove seat assembly from the crate.

b)Remove the four 5/16-18 whizlock nuts from the seat track studs at the bottom of the seat. Retain for use later.

c)Align the seat track studs on the bottom of the seat with the holes in the seat frame. Place seat on top of the frame and secure with the four 5/16-18 whizlock nuts remove in step b).

d)Connect the wire harness located under the seat on the left side of the mainframe to the seat switch underneath the seat.

3.5INSTALL MOTION CONTROL LEVERS.

3.5.1Loosen and remove the two (2) 3/8” x 1” bolts and spring disc washers which attach the motion control levers to the control arm shafts for shipping and the two (2) 3/8” x 1” bolts and spring disc washers which are screwed into the control arm shafts.

a)Install the left motion control lever onto the control arm shaft (See Figure 4) on the left side of the console. Place the lever (with the mounting plate towards the rear) on the outside of the control arm shaft and secure with the bolts and washers. Position the lever so the bolts are in the center of the slots on the lever mounting plate and tighten until snug. Repeat on opposite side of unit.

NOTE: There are two lever height options available. Place the levers in the top two holes to increase height of the levers, or in the bottom two holes to decrease the height of the levers.

If the levers do not align with each other, when in the neutral position, (See Figure

5)loosen the hardware and make the appropriate adjustment by sliding/tilting the lever(s) forward or backward until properly aligned and tighten hardware.

- 16 -

Page 20 Page 22
Image 21
Page 20 Page 22
Contents For Serial Nos 440,000 & Higher Potential Hazard Exmark Parts PLUS→ Program Operators Manual Table of Contents Your Safety is Involved SafetySafety Alert Symbol TrainingCarbon monoxide can kill you Potential Hazard Operation Safe Zone for Mowing There is no rollover protection when the roll bar is down Maintenance and Storage Safety Signs Do not Operate Without Guard Location Rubber Heat Shield Specifications Hydrostatic Ground Drive System TiresCutting Deck Dimensions Assembly InstructionsUncrate Mower Install Rollover Protection System Roll BAR Torque RequirementsLower Roll BAR Installation Service Battery Upper Roll BAR InstallationMachine is shipped with a filled lead acid battery Install Motion Control Levers Install SeatService Engine Service Hydraulic OIL Position Discharge ChuteCheck Tire Pressure Operation Instructions ControlsMotion Control Positions Push the lever forward and down to disengage the brake Operating Instructions PRE-STARTRotating blades under the mower deck are dangerous Transporting Maintenance & Adjustments Periodic MaintenanceService Interval Daily Service Interval Daily or more often in dry conditions Service Interval MonthlyService Interval Daily Blade Bolt Installation Check rollover protections systems roll bar pins Service Interval 40 hr Service Interval 40 hrsService Interval Refer to chart Lubrication Chart Service Interval Once YearlyCaster Wheel Assembly Service Interval 160 hrs Service Interval As Required Service Interval After First 250 hrs Then yearly thereafterService Interval 500 hrs Cutting Height Position AdjustmentsANTI-SCALP Roller Adjustment Self-tensioning No adjustment necessary Swivel Adjustment Spring Compression AdjustmentBelt Guide Positioning Mule Drive Belt AdjustmentBrake Adjustment No adjustment necessaryThrottle Tension Reverse Indicator Adjustment Motion Control Adjustment Caster Adjustment Mercury Switch DisposalWaste Disposal Motor OIL DisposalBattery Disposal Trouble ShootingMower Pulls Left or Right W/LEVERS Fully Forward Mower Cuts UnevenlyProblem Engine Troubleshooting TableElectrical Diagram Hydraulic Diagram Limited Warranty Exmark Turf Equipment Service Record Page See EXMARK’S Complete Line of Products for Turf Care
Top Page Image Contents