Exmark Lazer Z XS manual Engine Troubleshooting Table, Problem

Page 46

e)Check that the PTO is disengaged.

f)Check that the spark plug wires are properly connected.

g)Check for loose or faulty wiring connections.

h)Check for corrosion at all wiring connections. Even minor corrosion may cause a faulty connection. Clean connector terminals thoroughly with electrical contact cleaner, apply dielectric grease and reconnect.

NOTE: When disconnecting electrical connectors DO NOT pull on the wires to separate the connectors.

NOTE: After carefully checking the above steps, attempt to start the engine. If it does not start, contact your authorized Exmark service dealer.

IMPORTANT: It is essential that all operator safety mechanisms be connected and in proper operating condition prior to mower use.

When a problem occurs, do not overlook the simple causes. For example: starting problems could be caused by an empty fuel tank.

The following table lists some of the common causes of trouble. Do not attempt to service or replace major items or any items that call for special timing of adjustments procedures (such as valves, governor, etc.). Have this work done by your Engine Service Dealer.

ENGINE TROUBLESHOOTING TABLE

	PROBLEM	NO	IMPROPER	DIRT IN	DIRTY AIR	FAULTY	ENGINE	BLOCKED	INCORRECT	DIRTY	INSUFFICIENT
		NO	IMPROPER	DIRT IN	DIRTY AIR	SPARK	ENGINE	FUEL	OIL	AIR	BATTERY
		FUEL	FUEL	FUEL LINE	FILTER	SPARK	OVERLOADED	FUEL	OIL	AIR	BATTERY
						PLUG		FILTER	LEVEL	SCREEN	CHARGE
	Will not start	X		X	X	X	X	X			X
	Hard starting	X	X	X	X	X	X	X
	Stops suddenly	X		X	X		X	X	X	X
	Lacks power		X	X	X	X	X	X	X	X
	Operates erratically		X	X	X	X	X	X		X
	Knocks or pings		X				X			X
	Skips or misfires		X	X	X	X				X
	Backfires			X	X	X	X			X
	Overheats*			X	X		X		X	X
	High fuel consumption				X	X	X			X

- 41 -

Image 46

Contents For Serial Nos 440,000 & Higher Potential Hazard Exmark Parts PLUS→ Program Operators Manual Table of Contents Safety Alert Symbol SafetyYour Safety is Involved TrainingCarbon monoxide can kill you Potential Hazard Operation Safe Zone for Mowing There is no rollover protection when the roll bar is down Maintenance and Storage Safety Signs Do not Operate Without Guard Location Rubber Heat Shield Specifications Tires Hydrostatic Ground Drive SystemCutting Deck Uncrate Mower Install Rollover Protection System Roll BAR Assembly InstructionsDimensions Torque RequirementsLower Roll BAR Installation Upper Roll BAR Installation Service BatteryMachine is shipped with a filled lead acid battery Install Seat Install Motion Control LeversPosition Discharge Chute Service Engine Service Hydraulic OILCheck Tire Pressure Controls Operation InstructionsMotion Control Positions Push the lever forward and down to disengage the brake PRE-START Operating InstructionsRotating blades under the mower deck are dangerous Transporting Periodic Maintenance Maintenance & AdjustmentsService Interval Daily Service Interval Monthly Service Interval Daily or more often in dry conditionsService Interval Daily Blade Bolt Installation Check rollover protections systems roll bar pins Service Interval 40 hrs Service Interval 40 hrService Interval Refer to chart Service Interval Once Yearly Lubrication ChartCaster Wheel Assembly Service Interval 160 hrs Service Interval After First 250 hrs Then yearly thereafter Service Interval As RequiredService Interval 500 hrs Adjustments Cutting Height PositionANTI-SCALP Roller Adjustment Swivel Adjustment Spring Compression Adjustment Self-tensioning No adjustment necessaryMule Drive Belt Adjustment Belt Guide PositioningNo adjustment necessary Brake AdjustmentThrottle Tension Reverse Indicator Adjustment Motion Control Adjustment Waste Disposal Mercury Switch DisposalCaster Adjustment Motor OIL DisposalMower Pulls Left or Right W/LEVERS Fully Forward Trouble ShootingBattery Disposal Mower Cuts UnevenlyEngine Troubleshooting Table ProblemElectrical Diagram Hydraulic Diagram Limited Warranty Exmark Turf Equipment Service Record Page See EXMARK’S Complete Line of Products for Turf Care