Husqvarna Rider 320 AWD Adjusting the parking brake Rider, Can result in reduced braking ability

Page 18

Maintenance

3If necessary, the wires can be adjusted by tightening the adjuster nuts on each side of the steering collar. Do not over tighten the cables; they should only be drawn in towards the steering collar.

4Unscrew the belt shields and the side protectors. The protectors are fitted on both sides of the machine.

5Hold the cable, for example using an adjustable wrench, so that it does not twist. If the adjustment is only made on one side, the middle position of the steering will be affected.

6Check the wire tension on completion of the adjustment as per item 2.

7Screw on the belt shields and the side protectors. Remember to use the right screws in each mounting.

Adjusting the parking brake Rider 318

The parking brake is adjusted as follows:

1Loosen the locking nuts (1).

2Tension the cable using the adjuster screw (2) until the play in the cable is taken up.

3Tighten the locking nuts (1) after adjustment.

4The parking brake should be checked again after the adjustment has been made.

WARNING! A poorly adjusted parking brake

!can result in reduced braking ability.

Adjusting the parking brake Rider 320 AWD

Check that the parking brake is adjusted correctly by placing the machine on a slope with the front and rear axles disengaged.

Apply and lock the parking brake. When the machine does not stand still, the parking brake should be adjusted according to the following.

1 Remove the left-hand wing cover.

2 Loosen the locking nuts (1).

3Tension the cable using the adjuster screw (2) until the play in the cable is taken up.

4Tighten the locking nuts (1).

5The brake should be checked again after adjustment

6Assemble the left-hand wing cover.

Checking and adjusting of throttle wire

The throttle cable may need to be adjusted, if the engine does not respond as it should when accelerating, if it produces black smoke or maximum revs are not reached.

If doubts arise, contact your service representative.

1Loosen the clamping screw for the cable’s outer casing and move the throttle to the full throttle position.

2Pull the choke wire casing to the far right and tighten the clamping screw.

18 – English

Page 17 Page 19
Image 18
Page 17 Page 19
Contents Rider 318 Rider 320 AWD Contents Service journal Pre-delivery serviceAfter the first 8 hours Introduction KEY to Symbols SymbolsKEY to Symbols What is WHAT? Location of the controlsInsure your Rider Safety InstructionsSafety instructions General useDriving on slopes This is what you doMaintenance ChildrenTransport Presentation Release lever SeatFueling Release lever RiderStart the engine DrivingBefore starting Starting a cold engineDriving the Rider Starting the engine with a weak batteryConnecting the jump leads Stop the engineMaintenance Maintenance scheduleCleaning Checking and adjusting the steering wiresRemoving of the machine hoods Checking and adjusting of throttle wire Adjusting the parking brake RiderAdjusting the parking brake Rider 320 AWD Can result in reduced braking abilityChecking the fuel pump’s air filter Replacement of fuel filterReplacing the air filter Cool before starting to replace the air filterMain fuse Check the safety systemIgnition system Checking the tyre pressureFitting the cutting head Trapping your handAdjusting the parallelism of the cutting unit Removing the cutting unitChecking the cutting unit’s parallelism Replacing the cutting unit belts Service position for the cutting unit Placing in the service positionRestoring from service position Removing the BioClip plug Checking the bladesReplacing the blades Combi 103, CombiChanging the oil filter LubricationChecking the engine’s oil level Replacing the engine oilLubricating the belt adjuster Checking the transmission oil levelGeneral lubrication Troubleshooting schedule Winter storage ServiceStorage GuardTechnical Data EC Declaration of Conformity Applies to Europe only Cutting unit CombiBlade 1156985-26 ´z+X§T¶6X¨ ´z+X§T¶6X¨ Original instructions
Top Page Image Contents