Husqvarna Rider 318 manual EC Declaration of Conformity Applies to Europe only, Cutting unit Combi

Page 31

TECHNICAL DATA

Cutting unit

Combi 94

Combi 103

Combi 112

 

 

 

 

Cutting width, mm/inch

940/37

1030 / 41

1120 / 44.1

 

 

 

 

Cutting heights, 7 positions, mm/inch

25-75/0.98-2.95

25-75/0.98-2.95

25-75/0.98-2.95

 

 

 

 

Blade length, mm/inch

358/14.09

388/15.28

420 / 16,5

 

 

 

 

Blade

 

 

 

 

 

 

 

Part number

5796525-10

5041882-10

5041881-10

 

 

 

 

IMPORTANT INFORMATION When the service life of this product has been served and it is no longer used it should be returned to the dealer or to an applicable station for recycling.

IMPORTANT INFORMATION We reserve the right to change specifications and designs without prior notice so as to implement improvements.

Note that no legal claims are valid on the basis of information in this manual.

Use only genuine parts for repairs. The warranty is not valid if non genuine parts are used.

EC Declaration of Conformity (Applies to Europe only)

Husqvarna AB, SE-561 82 Huskvarna, Sweden, tel.: +46-36-146500, hereby declares that Husqvarna Rider 318 and Rider 320 AWD from 2014’s serial numbers and onwards (the year is clearly stated in plain text on the rating plate with subsequent serial number), complies with the requirements of the COUNCIL’S DIRECTIVE:

of May 17, 2006 ”relating to machinery” 2006/42/EC.

of December 15, 2004 ”relating to electromagnetic compatibility” 2004/108/EC.

of May 8, 2000 ”relating to the noise emissions in the environment” 2000/14/EC.

The following harmonised standards have been applied: EN ISO 12100-2, ISO 5395

Notified body: 0404, SMP Svensk Maskinprovning AB, Box 7035, SE-750 07 Uppsala, has issued reports regarding the assessment of conformity according to annex VI of the COUNCIL’S DIRECTIVE of May 8, 2000 ”relating to the noise emissions in the environment” 2000/14/EC.

The certificates have the numbers: 01/901/094, 01/901/095, 01/901/096

Huskvarna 19 may 2014

Claes Losdal, Development Manager/Garden Products

(Authorized representative for Husqvarna AB and responsible for technical documentation.)

English – 31

Page 30 Page 32
Image 31
Page 30 Page 32
Contents Rider 318 Rider 320 AWD Contents Pre-delivery service Service journalAfter the first 8 hours Introduction Symbols KEY to SymbolsKEY to Symbols Location of the controls What is WHAT?General use Safety InstructionsSafety instructions Insure your RiderThis is what you do Driving on slopesChildren MaintenanceTransport Presentation Release lever Rider SeatFueling Release leverStarting a cold engine DrivingBefore starting Start the engineStop the engine Starting the engine with a weak batteryConnecting the jump leads Driving the RiderMaintenance schedule MaintenanceChecking and adjusting the steering wires CleaningRemoving of the machine hoods Can result in reduced braking ability Adjusting the parking brake RiderAdjusting the parking brake Rider 320 AWD Checking and adjusting of throttle wireCool before starting to replace the air filter Replacement of fuel filterReplacing the air filter Checking the fuel pump’s air filterChecking the tyre pressure Check the safety systemIgnition system Main fuseTrapping your hand Fitting the cutting headRemoving the cutting unit Adjusting the parallelism of the cutting unitChecking the cutting unit’s parallelism Replacing the cutting unit belts Placing in the service position Service position for the cutting unitRestoring from service position Combi 103, Combi Checking the bladesReplacing the blades Removing the BioClip plugReplacing the engine oil LubricationChecking the engine’s oil level Changing the oil filterChecking the transmission oil level Lubricating the belt adjusterGeneral lubrication Troubleshooting schedule Guard ServiceStorage Winter storageTechnical Data Cutting unit Combi EC Declaration of Conformity Applies to Europe onlyBlade Original instructions 1156985-26 ´z+X§T¶6X¨ ´z+X§T¶6X¨
Top Page Image Contents