Husqvarna LZ30, LZ30C, LZ7230, LZ6127, LZ6130C, LZ7230C, LZ5227, LZ6130 manual Motion Control Levers

Page 19

CONTROLS

Motion Control Levers

The machine’s speed and direction are continuously variable using the two steering controls. The steering controls can be moved forward or backward about a neutral position. Furthermore, there is a neutral position, which is locked if the steering controls are moved outward.

When both controls are in the neutral position (N), the machine stands still.

By moving both controls an equal amount forward or backward, the machine moves in a straight line forward or backward respectively.

In order, for example, to turn right while moving forward, move the right control towards the neutral position. The rotation of the right wheel is reduced and the machine turns to the right.

Zero turn can be achieved by moving one control backward (behind the neutral position) and carefully moving the other steering control forward from its neutral position. The rotation direction when zero turning is determined by which steering control is moved backward behind the neutral position. If the left steering control is pulled backward, the machine turns to the left. Use extra care when using this maneuver.

8011-789

Steering controls

WARNING!

The machine can turn very rapidly if one steering control is moved much further forward than the other.

1

 

2

3

4

 

 

8011-7912

1.Forward

2.Neutral

3.Neutral slot, Neutral lock

4.Reverse

Motion control lever pattern (right side)

English-19

Image 19
Contents Operator Manual Page Contents English-4 Introduction Manufacturing Number Good ServiceImportant Information Symbols and DecalsRemove key before Safety Instructions SafetyGeneral Operation Never take passengers Slope Operation Personal Safety EquipmentChildren Safe Handling of Gasoline General Maintenance Or into anything. If necessary, make repairs Customer responsibilities TransportSpark Arresters Roll over Protection system RopsControls ControlsMotion Control Levers Tracking knob Hour meterParking Brake Ignition Switch Blade switchFuses Refueling Seat Lock Seat adjustment leverFuel shut off valve Throttle control Choke controlLifting Lever for the Mower Deck Cutting height lift pedal AccessoriesPump release valves Steering OperationOperation TrainingBefore Starting Roll bar and safety beltStarting the Engine Depress the control for disengaging the mower deck Press in and turn the ignition key to the start position Mowing no choke To attach jumper cables To start an engine with a weak batteryTo remove cables, reverse order Running Mower deck’s gauge wheels should be evenly adjustedOperating on hills Mowing Tips Moving by Hand Stopping the Engine25 50 100 MaintenanceLeast Hours Once Maintenance Before After Each Daily Weekly100 300 To clean battery and terminals BatteryReplacing battery Ignition System Safety SystemSafety system Throttle Cable Engine Cooling Air IntakeChoke Cable Air Filter Air filter housing and filterDust cap Engine Oil Cooler Fuel Pump Air Filter Fuel FilterDeck belt Checking the V-beltsTo replace deck belt Checking Tire Pressures Pump beltChecking the Parking Brake Checking the Blades Blade replacementAdjusting Cutting Height Adjusting the Mower DeckLeveling Hardware Cleaning and WashingRemoval and installation of caster wheel Caster WheelsLubrication Schedule LubricationShaft Bushings and Linkage Lubricating the CablesLubricating with Lubrication Schedule Engine Oil Changing the Engine Oil Checking the Oil Level Oil Type Oil RecommendationsFront Wheel Bearings Mower Deck Height AdjusterThrottle and Choke Cables, Lever Bearings Front Wheel MountMower Deck Struts Steering Control ShaftsChanging the Oil Filter Problem Cause Troubleshooting GuideEnglish-58 Storage ServiceWinter Storage For unit produced before Serial No Wiring DiagramsLZ5227 LZ6127 Engine Technical DataTransmission LZ5227 Z6127 Overall DimensionsProductivity LZ6130 LZ7230 Engine LZ6130C LZ7230C LZ6130 LZ7230 LZ30C LZ30Torque Specifications Conformity Certificates USA requirements Conformity CertificatesCE requirements Action Date, mtr reading, stamp, sign Service JournalService Journal Delivery ServiceAfter the First 5-8 Hours Hour Service English-71 English-72 English-73 At Least Once Each Year English-75 Warranty Statement 539 131254 R01 08/23/07