Husqvarna LZ6130C, LZ7230C manual Cutting height lift pedal, Pump release valves, Accessories

Page 25

CONTROLS

Cutting height lift pedal

On some models, there is a deck assist lift pedal to aid in maneuvering the deck lift.

IMPORTANT INFORMATION

In order to obtain an even cutting height it is important that the air pressure in all four tires is the same 15 psi (1 bar).

8011-465

Lift pedal

Pump release valves

IMPORTANT INFORMATION

Only rotate the valve ¼ to ½ turn to release the system.

Tighten the valve moderately.

Do not overtighten the valve when closing. Overtightening can damage the valve seat.

Pump release valves are located on the pumps. These valves release the system so the machine may be moved by hand when not running. Tilt the seat forward to gain access to the valves. Use a 5/8" wrench to open the valve.

Accessories

For mulching, there is a BioClip attachment available. The BioClip is mounted underneath the mower deck and includes control plates and BioClip blades.

8011-507

Pump release valve

8011-566

BioClip attachment

English-25

Image 25
Contents Operator Manual Page Contents English-4 Introduction Manufacturing Number Good ServiceImportant Information Symbols and DecalsRemove key before Safety Instructions SafetyGeneral Operation Never take passengers Slope Operation Personal Safety EquipmentChildren Safe Handling of Gasoline General Maintenance Or into anything. If necessary, make repairs Customer responsibilities TransportSpark Arresters Roll over Protection system RopsControls ControlsMotion Control Levers Tracking knob Hour meterParking Brake Ignition Switch Blade switchFuses Refueling Seat Lock Seat adjustment leverFuel shut off valve Throttle control Choke controlLifting Lever for the Mower Deck Cutting height lift pedal AccessoriesPump release valves Operation OperationTraining SteeringBefore Starting Roll bar and safety beltStarting the Engine Depress the control for disengaging the mower deck Press in and turn the ignition key to the start position Mowing no choke To attach jumper cables To start an engine with a weak batteryTo remove cables, reverse order Running Mower deck’s gauge wheels should be evenly adjustedOperating on hills Mowing Tips Moving by Hand Stopping the EngineLeast Hours Once Maintenance Before After Each MaintenanceDaily Weekly 25 50 100100 300 To clean battery and terminals BatteryReplacing battery Ignition System Safety SystemSafety system Throttle Cable Engine Cooling Air IntakeChoke Cable Air Filter Air filter housing and filterDust cap Engine Oil Cooler Fuel Pump Air Filter Fuel FilterDeck belt Checking the V-beltsTo replace deck belt Checking Tire Pressures Pump beltChecking the Parking Brake Checking the Blades Blade replacementAdjusting Cutting Height Adjusting the Mower DeckLeveling Removal and installation of caster wheel Cleaning and WashingCaster Wheels HardwareLubrication Schedule LubricationShaft Bushings and Linkage Lubricating the CablesLubricating with Lubrication Schedule Engine Oil Changing the Engine Oil Checking the Oil Level Oil Type Oil RecommendationsThrottle and Choke Cables, Lever Bearings Mower Deck Height AdjusterFront Wheel Mount Front Wheel BearingsMower Deck Struts Steering Control ShaftsChanging the Oil Filter Problem Cause Troubleshooting GuideEnglish-58 Storage ServiceWinter Storage For unit produced before Serial No Wiring DiagramsLZ5227 LZ6127 Engine Technical DataTransmission LZ5227 Z6127 Overall DimensionsProductivity LZ6130 LZ7230 Engine LZ6130C LZ7230C LZ6130 LZ7230 LZ30C LZ30Torque Specifications Conformity Certificates USA requirements Conformity CertificatesCE requirements Service Journal Service JournalDelivery Service Action Date, mtr reading, stamp, signAfter the First 5-8 Hours Hour Service English-71 English-72 English-73 At Least Once Each Year English-75 Warranty Statement 539 131254 R01 08/23/07