Husqvarna LZ30, LZ30C, LZ7230, LZ6127 manual Lubricating the Cables, Shaft Bushings and Linkage

Page 51

LUBRICATION

Lubricating the Cables

If possible, grease both ends of the cables and move the controls to end stop positions when lubricating. Refit the rubber covers on the cables after lubrication. Cables with sheaths will bind if they are not lubricated regularly. If a cable binds, it can disrupt operation.

If a cable binds, remove the cable and hang it vertically. Lubricate it with light engine oil until the oil begins to escape from the bottom.

Tip: Fill a small plastic bag with oil and tape it so that it seals against the sheath and allow the cable to hang vertically from the bag overnight. If you do not succeed in lubricating the cable, it must be replaced.

Shaft Bushings and Linkage

Lubricate the bearing of the shafts and linkage for brake system and steering with oil spray or oil can.

Lubricating with the

Lubrication Schedule

Hydraulic System, Oil Level

The hydraulic oil and filter must be replaced every 300 hours, and at least once a year. Contact an authorized service workshop.

Check the oil level in the hydraulic tank daily. The level shall be about ¾"-1" (19 - 25 mm) below the top of the tank.

Check connections, hoses, and tubes for damage or leaks. Replace or repair if doubtful.

Changing Oil and Filters

Oil and filter changes for the hydraulic system should be carried out by an authorized service workshop due to the risk of impurities enter the system.

Driver’s Seat

Tip the seat.

Lubricate the front hinges using an oil can.

Lubricate the lengthways adjustment mechanism with the oil can.

Lubricate the lengthways adjustment runners with the oil can.

IMPORTANT INFORMATION

Use minimal lubrication and remove excess lubricant so that is does not come into contact with belts or belt pulley drive surfaces.

Checking the hydraulic oil

8011-565

 

WARNING!

If a leak is suspected, use a piece of cardboard or wood, NOT your hands, to check for leaks. Escaping hydraulic oil under pressure can have sufficient force to penetrate the skin, causing serious injury.

If injured by escaping fluid, see a doctor at once. Serious infection or reaction can develop if proper medical treatment is not administered immediately.

8011-571

Lubricating the lengthways adjuster under the seat

English-51

Image 51
Contents Operator Manual Page Contents English-4 Introduction Manufacturing Number Good ServiceImportant Information Symbols and DecalsRemove key before Safety Safety InstructionsGeneral Operation Never take passengers Slope Operation Personal Safety EquipmentChildren Safe Handling of Gasoline General Maintenance Or into anything. If necessary, make repairs Customer responsibilities TransportSpark Arresters Roll over Protection system RopsControls ControlsMotion Control Levers Hour meter Tracking knobParking Brake Blade switch Ignition SwitchFuses Refueling Seat adjustment lever Seat LockFuel shut off valve Choke control Throttle controlLifting Lever for the Mower Deck Accessories Cutting height lift pedalPump release valves Steering OperationOperation TrainingRoll bar and safety belt Before StartingStarting the Engine Depress the control for disengaging the mower deck Press in and turn the ignition key to the start position Mowing no choke To start an engine with a weak battery To attach jumper cablesTo remove cables, reverse order Running Mower deck’s gauge wheels should be evenly adjustedOperating on hills Mowing Tips Moving by Hand Stopping the Engine25 50 100 MaintenanceLeast Hours Once Maintenance Before After Each Daily Weekly100 300 Battery To clean battery and terminalsReplacing battery Ignition System Safety SystemSafety system Engine Cooling Air Intake Throttle CableChoke Cable Air filter housing and filter Air FilterDust cap Engine Oil Cooler Fuel Pump Air Filter Fuel FilterChecking the V-belts Deck beltTo replace deck belt Pump belt Checking Tire PressuresChecking the Parking Brake Checking the Blades Blade replacementAdjusting the Mower Deck Adjusting Cutting HeightLeveling Hardware Cleaning and WashingRemoval and installation of caster wheel Caster WheelsLubrication Schedule LubricationLubricating the Cables Shaft Bushings and LinkageLubricating with Lubrication Schedule Engine Oil Changing the Engine Oil Checking the Oil Level Oil Type Oil RecommendationsFront Wheel Bearings Mower Deck Height AdjusterThrottle and Choke Cables, Lever Bearings Front Wheel MountSteering Control Shafts Mower Deck StrutsChanging the Oil Filter Problem Cause Troubleshooting GuideEnglish-58 Service StorageWinter Storage For unit produced before Serial No Wiring DiagramsTechnical Data LZ5227 LZ6127 EngineTransmission Overall Dimensions LZ5227 Z6127Productivity LZ6130 LZ7230 Engine LZ6130C LZ7230C LZ6130 LZ7230 LZ30C LZ30Torque Specifications Conformity Certificates Conformity Certificates USA requirementsCE requirements Action Date, mtr reading, stamp, sign Service JournalService Journal Delivery ServiceAfter the First 5-8 Hours Hour Service English-71 English-72 English-73 At Least Once Each Year English-75 Warranty Statement 539 131254 R01 08/23/07