Husqvarna LZ30, LZ30C, LZ7230, LZ6127, LZ6130C, LZ7230C, LZ5227, LZ6130 manual Engine Oil Cooler

Page 43

MAINTENANCE

1.Pull the main filter (outer) filter out.

2.Remove the inner filter.

3.Clean inside the filter housing, cover housing and dust cap. Wipe dry only.

4.Reinstall or replace the inner filter with the open end first, ensuring that it enters the housing recess. Push in to the end.

5.Reinstall or replace the outer filter with the open end first so that it enters the recess. Push in to the end.

6.Replace the end cover with the rubber valve pointing downwards and secure retaining clips.

IMPORTANT INFORMATION

The end cover must be installed with the rubber valve pointing downwards or the rubber valve will not function.

Engine Oil Cooler

Clean the outside of fins with a brush.

Remove the two screws holding the cooler unit to the blower housing.

Tilt the cooler downward.

Clean the inside of the cooler with a brush or with compressed air.

Reinstall the oil cooler to the blower housing

8011-449

Removing the main filter

8011-450

Removing the inner filter

8011-472

Engine oil cooler

English-43

Page 42 Page 44
Image 43
Page 42 Page 44
Contents Operator Manual Page Contents English-4 Introduction Manufacturing Number Good ServiceImportant Information Symbols and DecalsRemove key before Safety Instructions SafetyGeneral Operation Never take passengers Slope Operation Personal Safety EquipmentChildren Safe Handling of Gasoline General Maintenance Or into anything. If necessary, make repairs Customer responsibilities TransportSpark Arresters Roll over Protection system RopsControls ControlsMotion Control Levers Tracking knob Hour meterParking Brake Ignition Switch Blade switchFuses Refueling Seat Lock Seat adjustment leverFuel shut off valve Throttle control Choke controlLifting Lever for the Mower Deck Cutting height lift pedal AccessoriesPump release valves Steering OperationOperation TrainingBefore Starting Roll bar and safety beltStarting the Engine Depress the control for disengaging the mower deck Press in and turn the ignition key to the start position Mowing no choke To attach jumper cables To start an engine with a weak batteryTo remove cables, reverse order Running Mower deck’s gauge wheels should be evenly adjustedOperating on hills Mowing Tips Moving by Hand Stopping the Engine25 50 100 MaintenanceLeast Hours Once Maintenance Before After Each Daily Weekly100 300 To clean battery and terminals BatteryReplacing battery Ignition System Safety SystemSafety system Throttle Cable Engine Cooling Air IntakeChoke Cable Air Filter Air filter housing and filterDust cap Engine Oil Cooler Fuel Pump Air Filter Fuel FilterDeck belt Checking the V-beltsTo replace deck belt Checking Tire Pressures Pump beltChecking the Parking Brake Checking the Blades Blade replacementAdjusting Cutting Height Adjusting the Mower DeckLeveling Hardware Cleaning and WashingRemoval and installation of caster wheel Caster WheelsLubrication Schedule LubricationShaft Bushings and Linkage Lubricating the CablesLubricating with Lubrication Schedule Engine Oil Changing the Engine Oil Checking the Oil Level Oil Type Oil RecommendationsFront Wheel Bearings Mower Deck Height AdjusterThrottle and Choke Cables, Lever Bearings Front Wheel MountMower Deck Struts Steering Control ShaftsChanging the Oil Filter Problem Cause Troubleshooting GuideEnglish-58 Storage ServiceWinter Storage For unit produced before Serial No Wiring DiagramsLZ5227 LZ6127 Engine Technical DataTransmission LZ5227 Z6127 Overall DimensionsProductivity LZ6130 LZ7230 Engine LZ6130C LZ7230C LZ6130 LZ7230 LZ30C LZ30Torque Specifications Conformity Certificates USA requirements Conformity CertificatesCE requirements Action Date, mtr reading, stamp, sign Service JournalService Journal Delivery ServiceAfter the First 5-8 Hours Hour Service English-71 English-72 English-73 At Least Once Each Year English-75 Warranty Statement 539 131254 R01 08/23/07
Top Page Image Contents