Husqvarna LZ6130C, LZ7230C, LZ7230, LZ6127, LZ5227, LZ6130 Blade switch, Ignition Switch, Fuses

Page 21

CONTROLS

Blade switch

To engage the mower deck, pull the blade switch knob out. The mower blades are disengaged when the knob is pressed down fully.

8011-510

Blade Switch

Ignition Switch

The ignition key is placed on the control panel and is used to start and stop the engine.

WARNING!

Do not run the starter for more than five seconds each time. If the engine does not start, wait 10 seconds before retrying.

Fuses

The fuses are located in a holder to the left of the hydraulic tank. They are flat pin fuses of the same type used in automobiles.

There are three fuses as well as a socket for one spare fuse.

Fuse ratings and functions:

20 A, Primary fuse.

7.5 A, Mower deck coupling.

7.5 A, Accessory outlet.

Socket for spare fuse.

8011-748

Ignition Switch

8011-746

Fuses

English-21

Image 21
Contents Operator Manual Page Contents English-4 Introduction Manufacturing Number Good ServiceImportant Information Symbols and DecalsRemove key before Safety Safety InstructionsGeneral Operation Never take passengers Slope Operation Personal Safety EquipmentChildren Safe Handling of Gasoline General Maintenance Or into anything. If necessary, make repairs Customer responsibilities TransportSpark Arresters Roll over Protection system RopsControls ControlsMotion Control Levers Hour meter Tracking knobParking Brake Blade switch Ignition SwitchFuses Refueling Seat adjustment lever Seat LockFuel shut off valve Choke control Throttle controlLifting Lever for the Mower Deck Accessories Cutting height lift pedalPump release valves Operation OperationTraining SteeringRoll bar and safety belt Before StartingStarting the Engine Depress the control for disengaging the mower deck Press in and turn the ignition key to the start position Mowing no choke To start an engine with a weak battery To attach jumper cablesTo remove cables, reverse order Running Mower deck’s gauge wheels should be evenly adjustedOperating on hills Mowing Tips Moving by Hand Stopping the EngineLeast Hours Once Maintenance Before After Each MaintenanceDaily Weekly 25 50 100100 300 Battery To clean battery and terminalsReplacing battery Ignition System Safety SystemSafety system Engine Cooling Air Intake Throttle CableChoke Cable Air filter housing and filter Air FilterDust cap Engine Oil Cooler Fuel Pump Air Filter Fuel FilterChecking the V-belts Deck beltTo replace deck belt Pump belt Checking Tire PressuresChecking the Parking Brake Checking the Blades Blade replacementAdjusting the Mower Deck Adjusting Cutting HeightLeveling Removal and installation of caster wheel Cleaning and WashingCaster Wheels HardwareLubrication Schedule LubricationLubricating the Cables Shaft Bushings and LinkageLubricating with Lubrication Schedule Engine Oil Changing the Engine Oil Checking the Oil Level Oil Type Oil RecommendationsThrottle and Choke Cables, Lever Bearings Mower Deck Height AdjusterFront Wheel Mount Front Wheel BearingsSteering Control Shafts Mower Deck StrutsChanging the Oil Filter Problem Cause Troubleshooting GuideEnglish-58 Service StorageWinter Storage For unit produced before Serial No Wiring DiagramsTechnical Data LZ5227 LZ6127 EngineTransmission Overall Dimensions LZ5227 Z6127Productivity LZ6130 LZ7230 Engine LZ6130C LZ7230C LZ6130 LZ7230 LZ30C LZ30Torque Specifications Conformity Certificates Conformity Certificates USA requirementsCE requirements Service Journal Service JournalDelivery Service Action Date, mtr reading, stamp, signAfter the First 5-8 Hours Hour Service English-71 English-72 English-73 At Least Once Each Year English-75 Warranty Statement 539 131254 R01 08/23/07