Husqvarna LZ5227, LZ6130, LZ7230, LZ6127, LZ6130C, LZ7230C, LZ30, LZ30C Lubrication Schedule

Page 50

LUBRICATION

Lubrication Schedule

Lubrication schedule and Symbol Key

8011-673

12/12=	Every year	Lubricate with grease gun	Lubricate with oil can
1/52=	Every Week	Oil change	Level check
1/365=	Every day	Filter change

General

Remove the ignition key to prevent unintentional movements during lubrication. When lubricating with an oil can, it must be ﬁlled with engine oil.

When lubricating with grease, unless otherwise stated, use a high grade molybdenum disulphide grease. For daily use, the machine shall be lubricated twice weekly.

Wipe away excess grease after lubrication.

It is important to avoid getting lubricant on the belts or the drive surfaces on the belt pulleys. Should this happen, attempt to clean them with spirits. If the belt continues to slip after cleaning, it must be replaced. Gasoline or other petroleum products must not be used to clean belts.

English-50

Image 50

Contents Operator Manual Page Contents English-4 Introduction Good Service Manufacturing NumberSymbols and Decals Important InformationRemove key before General Operation SafetySafety Instructions Never take passengers Personal Safety Equipment Slope OperationChildren Safe Handling of Gasoline General Maintenance Or into anything. If necessary, make repairs Transport Customer responsibilitiesRoll over Protection system Rops Spark ArrestersControls ControlsMotion Control Levers Parking Brake Hour meterTracking knob Fuses Blade switchIgnition Switch Refueling Fuel shut off valve Seat adjustment leverSeat Lock Lifting Lever for the Mower Deck Choke controlThrottle control Pump release valves AccessoriesCutting height lift pedal Training OperationOperation SteeringStarting the Engine Roll bar and safety beltBefore Starting Depress the control for disengaging the mower deck Press in and turn the ignition key to the start position Mowing no choke To remove cables, reverse order To start an engine with a weak batteryTo attach jumper cables Mower deck’s gauge wheels should be evenly adjusted RunningOperating on hills Mowing Tips Stopping the Engine Moving by HandDaily Weekly MaintenanceLeast Hours Once Maintenance Before After Each 25 50 100100 300 Replacing battery BatteryTo clean battery and terminals Safety System Ignition SystemSafety system Choke Cable Engine Cooling Air IntakeThrottle Cable Dust cap Air ﬁlter housing and ﬁlterAir Filter Engine Oil Cooler Fuel Filter Fuel Pump Air FilterTo replace deck belt Checking the V-beltsDeck belt Checking the Parking Brake Pump beltChecking Tire Pressures Blade replacement Checking the BladesLeveling Adjusting the Mower DeckAdjusting Cutting Height Caster Wheels Cleaning and WashingRemoval and installation of caster wheel HardwareLubrication Lubrication ScheduleLubricating with Lubrication Schedule Lubricating the CablesShaft Bushings and Linkage Engine Oil Changing the Engine Oil Checking the Oil Level Oil Recommendations Oil TypeFront Wheel Mount Mower Deck Height AdjusterThrottle and Choke Cables, Lever Bearings Front Wheel BearingsChanging the Oil Filter Steering Control ShaftsMower Deck Struts Troubleshooting Guide Problem CauseEnglish-58 Winter Storage ServiceStorage Wiring Diagrams For unit produced before Serial NoTransmission Technical DataLZ5227 LZ6127 Engine Productivity Overall DimensionsLZ5227 Z6127 LZ6130 LZ7230 Engine LZ6130C LZ7230C LZ6130 LZ7230 LZ30 LZ30CTorque Speciﬁcations CE requirements Conformity CertificatesConformity Certiﬁcates USA requirements Delivery Service Service JournalService Journal Action Date, mtr reading, stamp, signAfter the First 5-8 Hours Hour Service English-71 English-72 English-73 At Least Once Each Year English-75 Warranty Statement 539 131254 R01 08/23/07