Contents | 3Com 11.3 specs

CONTENTS

ABOUT THIS GUIDE

	Introduction	5
	How to Use This Guide		5
	Conventions	6
	Year 2000 Compliance		6

1 OVERVIEW
	NETBuilder II Systems		7
	EZBuilt Preassembled NETBuilder II System 7
	Component System		7
	NETBuilder II Chassis DPE Module 7
	Software 7
	Installation Checklist		8

2INSTALLING SOFTWARE AND BOOTING A NETBUILDER II SYSTEM

Installing Software and Performing Initial Boot		9
Booting from the Flash Memory Card 9
Prerequisites	9
Booting an EZBuilt NETBuilder II System 9
Booting a Component NETBuilder II System		10
Making a Backup of the Flash Memory Card		10
Prerequisites	10
Procedure	10

Using the Backup Flash Card 11

3CHANGING THE BOOT SOURCE

	Using the Boot Command		13
	Conﬁguring the Primary Boot Source			14
	Prerequisites	14
	Procedure	14

4 CONFIGURING BASIC SETTINGS
	Logging on to the System		17
	Setting Up IP Routing 18
	Learning About the User Interfaces			18
	Accessing the User Interface 19
	Web Link Versus Menu-Driven Versus Command-Line Interface 19
	Using the Web Link Application			19
	Web Link Interface Description			20
	Using the Menu-Driven Interface			20

Using the Command-Line Interface 21

iii

Image 3

3Com 11.3 manual Contents

Contents

New Installation for Enterprise OS Software 95052-8145 3Com CorporationBayfront Plaza Santa Clara, California Contents 3COM Corporation Limited Warranty This Guide How to UseAbout this Guide Introduction Convention Description ConventionsList conventions that are used throughout this guide Icon Alerts you to This guide apply to all software packages ﬂash memory card for ﬁrst time NETBuilder II installationsOverview Software Change the primary boot source default as needed Install System Software and Boot See ChapterInstall software from a ﬂash memory card Change the Primary Boot Source See Chapter Flash Memory Card Installing Software and Booting Netbuilder II SystemInstalling Software Performing Initial Boot Booting from NETBuilder II System Making a BackupFlash Memory Card Flash Card Using the Backup Press Reset buttons to reboot Changing the Boot Source Using the BootCommand Conﬁguring Primary Boot Source At the Enterprise OS prompt, enter Primary Boot Source menu is displayed Changing the Boot Source Configuring Basic Settings Logging on toSystem Setting Up IP Routing Learning AboutUser Interfaces Application Menu-Driven Versus of three ways Command-Line Interface Web Link Interface Description Log in as root. Type Main menu Level 1 is displayed Abbreviated Syntax Full-Form Syntax Symbol Description Symbols Full and Abbreviated Syntax Examples Can be abbreviated toCan be shortened by abbreviating it to Variations in Command Syntax Entering Service Names in Command LinesDetermining the Display of Ports and Virtual Ports Command History Substitution Using Aliases Privilege Level Strings Syntax for Assigning ValuesNumeric Values Names Port and Path Naming Restrictions Media Addresses An example of a Frame Relay address Bridge/router or tunnel switches. In the global addressingAsynchronous Transfer Mode ATM address Decimal. The Dlci identiﬁes a virtual circuit on the Frame Network Layer Addresses Addresses are the same 00003333%080002005678 For more information on Internet addresses, subnet masks,Followed by the MAC address Network from all other IPX networks. The following example Getting Help Level PasswordObtaining Network Manager Privilege Information Setting the Time and DateSetting System Administrator SETDefault -SYS SysCONtact = John Smith 408 IPX OSI Assign Internet addresses to individual ports using Assigning an IP Address to a bridge/router Port DELete -SNMP COMmunity Anycom Enable the Snmp service by entering RemoteManagerCOMmunity Configuring Basic Settings Services Technical SupportOnline Technical 408 727 Access by Analog ModemAccess by Digital Modem 847 262 Latin America Country Telephone Number Asia Paciﬁc RimEurope Europe, South Africa, and Middle East Country Telephone Number Fax Number Numerics Index Snmp Snmp 3Com Corporation Limited Warranty Disclaimer