Manuals / 3M / Household Appliance / Pet Fence

3M 39600 manual Replacement Parts And Service Information, To Our Customers, Available Direct From

Models: 39600

1 70

Download 70 pages 16.15 Kb

Page 3

Image 3

Replacement Parts And Service Information

To Our Customers:

This is the 3M-Matic™/AccuGlide™/Scotch™ brand equipment you ordered. It has been set up and tested in the factory with "Scotch" brand tapes. If any problems occur when operating this equipment, and you desire a service call, or phone consultation, call, write or Fax the appropriate number listed below.

Included with each machine is an Instructions and Parts List manual.

SERVICE, REPLACEMENT PARTS AND ADDITIONAL MANUALS

AVAILABLE DIRECT FROM:

Order parts by part number, part description and quantity required. Also, when ordering parts and/or additional manuals, include machine name, number and type.

3M Packaging Systems Division

3M Center, Building 220-8W-01 St. Paul, MN 55144-1000 1-800/328 1390

"3M-Matic", "AccuGlide" and “Scotch” are trademarks of 3M, St. Paul, Minnesota 55144-1000

Printed in U.S.A.

Page 3

Image 3

3M 39600 Replacement Parts And Service Information, To Our Customers, Service, Replacement Parts And Additional Manuals

Contents

3M-Matic Adjustable Case Sealer withInstructions and Parts List Important Safety Information241 Venture Drive Replacement Parts and Service InformationTo Our Customers 3M/Tape Dispenser PartsAVAILABLE DIRECT FROM Replacement Parts And Service InformationSERVICE, REPLACEMENT PARTS AND ADDITIONAL MANUALS To Our CustomersInstruction Manual Table of ContentsSection I - 800a Adjustable Case Sealer 800a, Type Adjustable Case SealerTable of Contents Continued PageSection II - AccuGlide II STD 2 Inch Taping Heads Description 3M-MaticTM 800a Adjustable Case Sealer, Type800a Contents Figure 1-2 - Electrical Warning Label Important SafeguardsThis safety alert symbol identifies important messages in this manual Figure 1-1 - Knife Warning LabelFigure 1-6 - Operating Notice Label The Safety Instructions label, shown inFigure 1-5 - Safety Instructions Label Figure 1-4 - Stop and Off/On LabelsFigure 1-8 - Knife Warning Label Figure 1-9 - Tape Threading LabelFigure 1-10 - Pinch Point Caution Label THIS PAGE IS BLANK 4. Tape 1. Power Requirements2. Operating Rate 3. Operating ConditionsBox Length In Direction Of Seal Must Be Greater Than Box Height Specifications Continued9. Box Weight and Size Capacities Weight Box SizeMachine Dimensions MinimumMaximum THIS PAGE IS BLANK WARNING - Follow this step carefully as spring pressure is Installation and Set-UpReceiving And Handling Machine Set-UpCAUTION - Machine weighs approximately 159 kg 350 pounds uncrated Installation and Set-Up ContinuedFigure 2-1 - 800a Frame Set-Up WARNING - Keep hands/fingers away from tape cut-off knife underTAPE DRUM BRACKET Lower Taping Head WARNING - To prevent shock and fire hazard Position extension Figure 3-1 - Case Sealer Components, Left Front View OperationWARNINGS 2. Turn electrical supply off when machine is not in useElectrical On/Off Switch Emergency Stop SwitchFigure 3-2 - Side Drive Belts Figure 3-3 - Upper Taping Head Box Size Set-Upfrom the machine before operating when machine is runningFigure 3-5 - Check Adjustment CAUTION - Be sure all packaging materials and tools are removedBox Sealing Figure 4-1 - Frame Lubrication Points Knife Replacement, Taping Head MaintenanceWARNING - Turn off electrical power supply and disconnect CleaningDrive Belts WARNING - The following procedure must be performed bycould result Circuit BreakerFigure 4-4 - Box Drive Belt Tension Adjustment, Top View Figure 4-3 - Box Drive Assembly, Infeed EndAdjustments Taping Head Adjustmentscould result Drive Belt Tension THIS PAGE IS BLANK WARNINGS Special Set-Up ProcedureWARNING - Turn off electrical power and disconnect power cord from Changing Tape Leg LengthFigure 5-2 - Drive Belt Assembly, Disassembly Special Set-Up Procedure ContinuedWARNING - Turn off electrical power and disconnect power cord from Drive Belt Assembly Heightup or severe injury or equipment damage could result WARNING - Turn off electrical power and disconnect power cord fromBox Height Range Outer Column - Re-PositioningFigure 5-4 - Upper Frame Removal Special Set-Up Procedure ContinuedFigure 5-6 - Chain Removal Figure 5-5 - Crank/Chain GuardsFigure 5-7 - Column Spacers/Columns Cause TroubleshootingTroubleshooting Guide ProblemTHIS PAGE IS BLANK Electrical Diagram Figure 7 - Electrical Diagramdangerous voltages. Severe injury or equipment damage could result THIS PAGE IS BLANK Tool Kit 800a Adjustable Case Sealer, TypeSpare Parts/Tools Spare PartsOptions/Accessories Option/AccessoryPart Number Replacement Parts Illustrations and Parts List 800a Adjustable Case Sealer, TypeWith AccuGlide II STD 2 Inch Taping Heads THIS PAGE IS BLANK 800a Assembly 800a Adjustable Case Sealer W/AccuGlide II STD 2 Inch Taping Heads800a Adjustable Case Sealer Ref. No 3M Part NoDescription 800a Adjustable Case Sealer Ref. No 3M Part NoDescription 800a Adjustable Case Sealer Ref. No 3M Part NoDescription 800a Adjustable Case Sealer Ref. No 3M Part NoDescription 800a Adjustable Case Sealer Figure 6162/1 of Description Figure 6162 page 1 ofRef. No 3M Part No800a Adjustable Case Sealer Figure 6162/2 of Description Figure 6162 page 2 ofRef. No 3M Part No800a Adjustable Case Sealer Figure 6163/1 of Description Figure 6163 page 1 ofRef. No 3M Part No800a Adjustable Case Sealer Figure 6163/2 of Description Figure 6163 page 2 ofRef. No 3M Part No800a Adjustable Case Sealer Figure 6164/1 of Description Figure 6164 page 1 ofRef. No 3M Part No800a Adjustable Case Sealer Figure 6164/2 of Description Figure 6164 page 2 ofRef. No 3M Part No800a Adjustable Case Sealer Ref. No 3M Part NoDescription 800a Adjustable Case Sealer Ref. No 3M Part NoDescription 800a Adjustable Case Sealer Safety and Information Labels Description 800a Safety and Information LabelsRef. No 3M Part No