Manuals / 3M / Household Appliance / Pet Fence

3M 39600 manual Ref. No, 3M Part No, Description

Models: 39600

1 70

Download 70 pages 16.15 Kb

Page 68

Figure 6166

Ref. No.	3M Part No.	Description
6166-1	78-8100-1218-3	Housing – Wire
6166-2	78-8060-7758-8	Fairlead – /20
6166-3	26-1003-7963-0	Screw – Soc Hd, M8 x 16
6166-4	78-8076-4636-5	Strap – Wire
6166-5	78-8010-7163-6	Screw – Hex Hd, M5 x 10
6166-6	78-8005-5741-1	Washer – Flat, M5
6166-7	78-8010-7417-6	Nut – Hex, M5
6166-8	78-8060-7631-7	Connector – 3/8 Inch
6166-9	78-8060-8154-9	Sleeving – 0,90 MT
6166-10	78-8060-8029-3	Clamp – 140 x 3,5
6166-11	78-8100-1219-1	Cover – Housing
6166-12	78-8010-7157-8	Screw – Hex Hd, M4 x 10
6166-13	78-8017-9018-5	Washer – Plain, M4

63

Image 68

3M 39600 manual Ref. No, 3M Part No, Description

Contents

Adjustable Case Sealer with Instructions and Parts ListImportant Safety Information 3M-MaticReplacement Parts and Service Information To Our Customers3M/Tape Dispenser Parts 241 Venture DriveReplacement Parts And Service Information SERVICE, REPLACEMENT PARTS AND ADDITIONAL MANUALSTo Our Customers AVAILABLE DIRECT FROMTable of Contents Section I - 800a Adjustable Case Sealer800a, Type Adjustable Case Sealer Instruction ManualSection II - AccuGlide II STD 2 Inch Taping Heads Table of Contents ContinuedPage 3M-MaticTM 800a Adjustable Case Sealer, Type Description800a Contents Important Safeguards This safety alert symbol identifies important messages in this manualFigure 1-1 - Knife Warning Label Figure 1-2 - Electrical Warning LabelThe Safety Instructions label, shown in Figure 1-5 - Safety Instructions LabelFigure 1-4 - Stop and Off/On Labels Figure 1-6 - Operating Notice LabelFigure 1-10 - Pinch Point Caution Label Figure 1-8 - Knife Warning LabelFigure 1-9 - Tape Threading Label THIS PAGE IS BLANK 1. Power Requirements 2. Operating Rate3. Operating Conditions 4. TapeSpecifications Continued 9. Box Weight and Size Capacities WeightBox Size Box Length In Direction Of Seal Must Be Greater Than Box HeightMaximum Machine DimensionsMinimum THIS PAGE IS BLANK Installation and Set-Up Receiving And HandlingMachine Set-Up WARNING - Follow this step carefully as spring pressure isInstallation and Set-Up Continued Figure 2-1 - 800a Frame Set-UpWARNING - Keep hands/fingers away from tape cut-off knife under CAUTION - Machine weighs approximately 159 kg 350 pounds uncratedTAPE DRUM BRACKET Lower Taping Head WARNING - To prevent shock and fire hazard Position extension Operation Figure 3-1 - Case Sealer Components, Left Front View2. Turn electrical supply off when machine is not in use Electrical On/Off SwitchEmergency Stop Switch WARNINGSBox Size Set-Up Figure 3-2 - Side Drive Belts Figure 3-3 - Upper Taping Headwhen machine is running Figure 3-5 - Check AdjustmentCAUTION - Be sure all packaging materials and tools are removed from the machine before operatingBox Sealing Maintenance WARNING - Turn off electrical power supply and disconnectCleaning Figure 4-1 - Frame Lubrication Points Knife Replacement, Taping HeadWARNING - The following procedure must be performed by could resultCircuit Breaker Drive BeltsFigure 4-3 - Box Drive Assembly, Infeed End Figure 4-4 - Box Drive Belt Tension Adjustment, Top Viewcould result Drive Belt Tension AdjustmentsTaping Head Adjustments THIS PAGE IS BLANK Special Set-Up Procedure WARNING - Turn off electrical power and disconnect power cord fromChanging Tape Leg Length WARNINGSSpecial Set-Up Procedure Continued WARNING - Turn off electrical power and disconnect power cord fromDrive Belt Assembly Height Figure 5-2 - Drive Belt Assembly, DisassemblyWARNING - Turn off electrical power and disconnect power cord from Box Height RangeOuter Column - Re-Positioning up or severe injury or equipment damage could resultSpecial Set-Up Procedure Continued Figure 5-4 - Upper Frame RemovalFigure 5-5 - Crank/Chain Guards Figure 5-6 - Chain RemovalFigure 5-7 - Column Spacers/Columns Troubleshooting Troubleshooting GuideProblem CauseTHIS PAGE IS BLANK dangerous voltages. Severe injury or equipment damage could result Electrical DiagramFigure 7 - Electrical Diagram THIS PAGE IS BLANK 800a Adjustable Case Sealer, Type Spare Parts/ToolsSpare Parts Tool KitPart Number Options/AccessoriesOption/Accessory With AccuGlide II STD 2 Inch Taping Heads Replacement Parts Illustrations and Parts List800a Adjustable Case Sealer, Type THIS PAGE IS BLANK 800a Adjustable Case Sealer W/AccuGlide II STD 2 Inch Taping Heads 800a Assembly800a Adjustable Case Sealer Description Ref. No3M Part No 800a Adjustable Case Sealer Description Ref. No3M Part No 800a Adjustable Case Sealer Description Ref. No3M Part No 800a Adjustable Case Sealer Description Ref. No3M Part No 800a Adjustable Case Sealer Figure 6162/1 of Figure 6162 page 1 of Ref. No3M Part No Description800a Adjustable Case Sealer Figure 6162/2 of Figure 6162 page 2 of Ref. No3M Part No Description800a Adjustable Case Sealer Figure 6163/1 of Figure 6163 page 1 of Ref. No3M Part No Description800a Adjustable Case Sealer Figure 6163/2 of Figure 6163 page 2 of Ref. No3M Part No Description800a Adjustable Case Sealer Figure 6164/1 of Figure 6164 page 1 of Ref. No3M Part No Description800a Adjustable Case Sealer Figure 6164/2 of Figure 6164 page 2 of Ref. No3M Part No Description800a Adjustable Case Sealer Description Ref. No3M Part No 800a Adjustable Case Sealer Description Ref. No3M Part No 800a Adjustable Case Sealer Safety and Information Labels 800a Safety and Information Labels Ref. No3M Part No Description