Manuals / 3M / Household Appliance / Pet Fence

3M 39600 manual Troubleshooting Guide, Problem, Cause, Correction

Models: 39600

1 70

Download 70 pages 16.15 Kb

Page 36

Troubleshooting

Troubleshooting

The Troubleshooting Guide lists some possible machine problems, causes and corrections. Also see Section II, "Troubleshooting", pages 15 and 16 for taping head problems.

Troubleshooting Guide
Problem	Cause	Correction
Drive belts do not convey boxes	Narrow boxes	Check machine specifications.
		Boxes are narrower than
		recommended, causing slippage
		and premature belt wear.

Worn drive belts

Top taping head does not apply enough pressure

Top flap compression rollers in too tight

Taping head applying spring holder missing

Taping head applying spring set too high

Replace drive belts

Adjust the box height adjustment with the crank

Readjust compression rollers

Replace spring holder

Reduce spring pressure

Drive belts do not turn	Worn or missing friction rings	Replace friction rings
	Drive belt tension too low	Adjust belt tension
	Electrical disconnect	Check power and electrical plug
	Circuit breaker not at correct	Set to correct current value
	setting
	Motor not turning	Evaluate problem and correct

Upper and lower applying	Machine adjusted below minimum	Set taping heads to apply 48 mm
mechanisms interfere with each		[2 inch] leg lengths
other

Drive belt break	Worn belt	Replace belt
	Excessive belt tension	Tension to 3.5 kg [7 lbs] per
		adjustment section

Squeaking noise as boxes pass	Dry column bearings	Lubricate column bearings
through machine
	Defective column bearings	Replace column bearings

Tape not centered on box seam	Tape drum not centered	Reposition tape drum
	Box flaps not of equal length	Check box specifications

31

Image 36

3M 39600 manual Troubleshooting Guide, Problem, Cause, Correction

Contents

Adjustable Case Sealer with Instructions and Parts ListImportant Safety Information 3M-MaticReplacement Parts and Service Information To Our Customers3M/Tape Dispenser Parts 241 Venture DriveReplacement Parts And Service Information SERVICE, REPLACEMENT PARTS AND ADDITIONAL MANUALSTo Our Customers AVAILABLE DIRECT FROMTable of Contents Section I - 800a Adjustable Case Sealer800a, Type Adjustable Case Sealer Instruction ManualTable of Contents Continued PageSection II - AccuGlide II STD 2 Inch Taping Heads 3M-MaticTM 800a Adjustable Case Sealer, Type Description800a Contents Important Safeguards This safety alert symbol identifies important messages in this manualFigure 1-1 - Knife Warning Label Figure 1-2 - Electrical Warning LabelThe Safety Instructions label, shown in Figure 1-5 - Safety Instructions LabelFigure 1-4 - Stop and Off/On Labels Figure 1-6 - Operating Notice LabelFigure 1-8 - Knife Warning Label Figure 1-9 - Tape Threading LabelFigure 1-10 - Pinch Point Caution Label THIS PAGE IS BLANK 1. Power Requirements 2. Operating Rate3. Operating Conditions 4. TapeSpecifications Continued 9. Box Weight and Size Capacities WeightBox Size Box Length In Direction Of Seal Must Be Greater Than Box HeightMachine Dimensions MinimumMaximum THIS PAGE IS BLANK Installation and Set-Up Receiving And HandlingMachine Set-Up WARNING - Follow this step carefully as spring pressure isInstallation and Set-Up Continued Figure 2-1 - 800a Frame Set-UpWARNING - Keep hands/fingers away from tape cut-off knife under CAUTION - Machine weighs approximately 159 kg 350 pounds uncratedTAPE DRUM BRACKET Lower Taping Head WARNING - To prevent shock and fire hazard Position extension Operation Figure 3-1 - Case Sealer Components, Left Front View2. Turn electrical supply off when machine is not in use Electrical On/Off SwitchEmergency Stop Switch WARNINGSBox Size Set-Up Figure 3-2 - Side Drive Belts Figure 3-3 - Upper Taping Headwhen machine is running Figure 3-5 - Check AdjustmentCAUTION - Be sure all packaging materials and tools are removed from the machine before operatingBox Sealing Maintenance WARNING - Turn off electrical power supply and disconnectCleaning Figure 4-1 - Frame Lubrication Points Knife Replacement, Taping HeadWARNING - The following procedure must be performed by could resultCircuit Breaker Drive BeltsFigure 4-3 - Box Drive Assembly, Infeed End Figure 4-4 - Box Drive Belt Tension Adjustment, Top ViewAdjustments Taping Head Adjustmentscould result Drive Belt Tension THIS PAGE IS BLANK Special Set-Up Procedure WARNING - Turn off electrical power and disconnect power cord fromChanging Tape Leg Length WARNINGSSpecial Set-Up Procedure Continued WARNING - Turn off electrical power and disconnect power cord fromDrive Belt Assembly Height Figure 5-2 - Drive Belt Assembly, DisassemblyWARNING - Turn off electrical power and disconnect power cord from Box Height RangeOuter Column - Re-Positioning up or severe injury or equipment damage could resultSpecial Set-Up Procedure Continued Figure 5-4 - Upper Frame RemovalFigure 5-5 - Crank/Chain Guards Figure 5-6 - Chain RemovalFigure 5-7 - Column Spacers/Columns Troubleshooting Troubleshooting GuideProblem CauseTHIS PAGE IS BLANK Electrical Diagram Figure 7 - Electrical Diagramdangerous voltages. Severe injury or equipment damage could result THIS PAGE IS BLANK 800a Adjustable Case Sealer, Type Spare Parts/ToolsSpare Parts Tool KitOptions/Accessories Option/AccessoryPart Number Replacement Parts Illustrations and Parts List 800a Adjustable Case Sealer, TypeWith AccuGlide II STD 2 Inch Taping Heads THIS PAGE IS BLANK 800a Adjustable Case Sealer W/AccuGlide II STD 2 Inch Taping Heads 800a Assembly800a Adjustable Case Sealer Ref. No 3M Part NoDescription 800a Adjustable Case Sealer Ref. No 3M Part NoDescription 800a Adjustable Case Sealer Ref. No 3M Part NoDescription 800a Adjustable Case Sealer Ref. No 3M Part NoDescription 800a Adjustable Case Sealer Figure 6162/1 of Figure 6162 page 1 of Ref. No3M Part No Description800a Adjustable Case Sealer Figure 6162/2 of Figure 6162 page 2 of Ref. No3M Part No Description800a Adjustable Case Sealer Figure 6163/1 of Figure 6163 page 1 of Ref. No3M Part No Description800a Adjustable Case Sealer Figure 6163/2 of Figure 6163 page 2 of Ref. No3M Part No Description800a Adjustable Case Sealer Figure 6164/1 of Figure 6164 page 1 of Ref. No3M Part No Description800a Adjustable Case Sealer Figure 6164/2 of Figure 6164 page 2 of Ref. No3M Part No Description800a Adjustable Case Sealer Ref. No 3M Part NoDescription 800a Adjustable Case Sealer Ref. No 3M Part NoDescription 800a Adjustable Case Sealer Safety and Information Labels 800a Safety and Information Labels Ref. No3M Part No Description