Manuals / 3M / Household Appliance / Pet Fence

3M 39600 manual 5 - Crank/Chain Guards, 6 - Chain Removal

Models: 39600

1 70

Download 70 pages 16.15 Kb

Page 34

Image 34

Special Set-Up Procedure (Continued)

4.Remove M6 x 16 hex hd screw, special washer and drive belt width adjustment crank.

Figure 5-5.

5.Remove side covers (2) from each side of machine bed. Figure 5-5.

6.Remove chain. If necessary, slip width adjustment crank on shaft and rotate until chain master link is in convenient position for removal.

Figure 5-5 – Crank/Chain Guards

Important – Before removing chain, mark both front and rear sprockets/chain with chalk or paint to be sure sprockets/chain when re-assembled, will be in same position as before disassembly. Figure 5-6A and B. Do not rotate sprockets once chain is removed. (This would result in the right and left drive assemblies not being parallel.)

Remove chain master link and remove chain. Figure 5-6C.

Figure 5-6 – Chain Removal

Page 34

Image 34

3M 39600 manual 5 - Crank/Chain Guards, 6 - Chain Removal

Contents

Important Safety Information Adjustable Case Sealer withInstructions and Parts List 3M-Matic3M/Tape Dispenser Parts Replacement Parts and Service InformationTo Our Customers 241 Venture DriveTo Our Customers Replacement Parts And Service InformationSERVICE, REPLACEMENT PARTS AND ADDITIONAL MANUALS AVAILABLE DIRECT FROM800a, Type Adjustable Case Sealer Table of ContentsSection I - 800a Adjustable Case Sealer Instruction ManualPage Table of Contents ContinuedSection II - AccuGlide II STD 2 Inch Taping Heads 3M-MaticTM 800a Adjustable Case Sealer, Type Description800a Contents Figure 1-1 - Knife Warning Label Important SafeguardsThis safety alert symbol identifies important messages in this manual Figure 1-2 - Electrical Warning LabelFigure 1-4 - Stop and Off/On Labels The Safety Instructions label, shown inFigure 1-5 - Safety Instructions Label Figure 1-6 - Operating Notice LabelFigure 1-9 - Tape Threading Label Figure 1-8 - Knife Warning LabelFigure 1-10 - Pinch Point Caution Label THIS PAGE IS BLANK 3. Operating Conditions 1. Power Requirements2. Operating Rate 4. TapeBox Size Specifications Continued9. Box Weight and Size Capacities Weight Box Length In Direction Of Seal Must Be Greater Than Box HeightMinimum Machine DimensionsMaximum THIS PAGE IS BLANK Machine Set-Up Installation and Set-UpReceiving And Handling WARNING - Follow this step carefully as spring pressure isWARNING - Keep hands/fingers away from tape cut-off knife under Installation and Set-Up ContinuedFigure 2-1 - 800a Frame Set-Up CAUTION - Machine weighs approximately 159 kg 350 pounds uncratedTAPE DRUM BRACKET Lower Taping Head WARNING - To prevent shock and fire hazard Position extension Operation Figure 3-1 - Case Sealer Components, Left Front ViewEmergency Stop Switch 2. Turn electrical supply off when machine is not in useElectrical On/Off Switch WARNINGSBox Size Set-Up Figure 3-2 - Side Drive Belts Figure 3-3 - Upper Taping HeadCAUTION - Be sure all packaging materials and tools are removed when machine is runningFigure 3-5 - Check Adjustment from the machine before operatingBox Sealing Cleaning MaintenanceWARNING - Turn off electrical power supply and disconnect Figure 4-1 - Frame Lubrication Points Knife Replacement, Taping HeadCircuit Breaker WARNING - The following procedure must be performed bycould result Drive BeltsFigure 4-3 - Box Drive Assembly, Infeed End Figure 4-4 - Box Drive Belt Tension Adjustment, Top ViewTaping Head Adjustments Adjustmentscould result Drive Belt Tension THIS PAGE IS BLANK Changing Tape Leg Length Special Set-Up ProcedureWARNING - Turn off electrical power and disconnect power cord from WARNINGSDrive Belt Assembly Height Special Set-Up Procedure ContinuedWARNING - Turn off electrical power and disconnect power cord from Figure 5-2 - Drive Belt Assembly, DisassemblyOuter Column - Re-Positioning WARNING - Turn off electrical power and disconnect power cord fromBox Height Range up or severe injury or equipment damage could resultSpecial Set-Up Procedure Continued Figure 5-4 - Upper Frame RemovalFigure 5-5 - Crank/Chain Guards Figure 5-6 - Chain RemovalFigure 5-7 - Column Spacers/Columns Problem TroubleshootingTroubleshooting Guide CauseTHIS PAGE IS BLANK Figure 7 - Electrical Diagram Electrical Diagramdangerous voltages. Severe injury or equipment damage could result THIS PAGE IS BLANK Spare Parts 800a Adjustable Case Sealer, TypeSpare Parts/Tools Tool KitOption/Accessory Options/AccessoriesPart Number 800a Adjustable Case Sealer, Type Replacement Parts Illustrations and Parts ListWith AccuGlide II STD 2 Inch Taping Heads THIS PAGE IS BLANK 800a Adjustable Case Sealer W/AccuGlide II STD 2 Inch Taping Heads 800a Assembly800a Adjustable Case Sealer 3M Part No Ref. NoDescription 800a Adjustable Case Sealer 3M Part No Ref. NoDescription 800a Adjustable Case Sealer 3M Part No Ref. NoDescription 800a Adjustable Case Sealer 3M Part No Ref. NoDescription 800a Adjustable Case Sealer Figure 6162/1 of 3M Part No Figure 6162 page 1 ofRef. No Description800a Adjustable Case Sealer Figure 6162/2 of 3M Part No Figure 6162 page 2 ofRef. No Description800a Adjustable Case Sealer Figure 6163/1 of 3M Part No Figure 6163 page 1 ofRef. No Description800a Adjustable Case Sealer Figure 6163/2 of 3M Part No Figure 6163 page 2 ofRef. No Description800a Adjustable Case Sealer Figure 6164/1 of 3M Part No Figure 6164 page 1 ofRef. No Description800a Adjustable Case Sealer Figure 6164/2 of 3M Part No Figure 6164 page 2 ofRef. No Description800a Adjustable Case Sealer 3M Part No Ref. NoDescription 800a Adjustable Case Sealer 3M Part No Ref. NoDescription 800a Adjustable Case Sealer Safety and Information Labels 3M Part No 800a Safety and Information LabelsRef. No Description